* [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
@ 2019-05-20 15:27 Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 01/14] Marvell/Library: MvGpioLib: Extend GPIO pin description Marcin Wojtas
` (14 more replies)
0 siblings, 15 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
Hi,
Thank you for thorough review of v1. I submit second
version of the Armada7k8k PCIE support. I addressed
all comments. There is no functional change to initial
patchset, but mostly clean-up and improvements - please
refer to the changelog below.
The patches are available in the github:
https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/commits/pcie-upstream-r20190520
I'm looking forward to your comments or remarks.
Best regards,
Marcin
Changelog:
v1->v2:
*All
- s/PcieBaseAddress/PcieDbiAdress/
*2/14
- fix alignment in comment
* 3/14
- add CONST** to library callback
* 4/14
- add missing reset GPIO to McBin description
* 5/15
- add CONST** to protocol callback
* 6/14
- cleanup all casting in file
- use MAX_UINTx macros
- add Linaro copyright
- use MmioWrite8 instead of volatile in PciExpressReadBuffer
- correct commient in IgnoreBusDeviceFunction ()
- fix typo in commit message
* 7/10
- correct line endings
- use temporary variable for memory description in PciHostBridgeResourceConflict
- use MAX_UINTx macros
- add comments around stalls and MemoryFence in GPIO reset
- keep the reset active for 150ms
- assign translation values instead of asserting
*8/14
- assign gArmTokenSpaceGuid.PcdPciIoTranslation value in .dsc
* 9-11/14
- correct line endings
- remove unused methods
- extend commit messages with 32k shift description
Ard Biesheuvel (1):
Marvell/Armada7k8k: Add PciExpressLib implementation
Marcin Wojtas (13):
Marvell/Library: MvGpioLib: Extend GPIO pin description
Marvell/Library: ArmadaSoCDescLib: Add PCIE information
Marvell/Library: ArmadaBoardDescLib: Add PCIE information
Marvell/Armada7k8k: Extend board description libraries with PCIE
Marvell/Armada7k8k: MvBoardDesc: Extend protocol with PCIE support
Marvell/Armada7k8k: Implement PciHostBridgeLib
Marvell/Armada7k8k: Enable PCIE support
Marvell/Armada80x0McBin: Enable ACPI PCIE support
Marvell/Armada80x0Db: Enable ACPI PCIE support
Marvell/Armada70x0Db: Enable ACPI PCIE support
Marvell/Armada80x0McBin: DeviceTree: Use pci-host-generic driver
Marvell/Armada7k8k: Remove duplication in .dsc files
Marvell/Armada7k8: Add 'acpiview' shell command to build
Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc | 19 +-
Platform/Marvell/Armada70x0Db/Armada70x0Db.dsc | 4 +-
Platform/Marvell/Armada80x0Db/Armada80x0Db.dsc | 4 +-
Platform/SolidRun/Armada80x0McBin/Armada80x0McBin.dsc | 4 +-
Silicon/Marvell/Armada7k8k/Armada7k8k.fdf | 5 +
Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db.inf | 1 +
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db.inf | 1 +
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin.inf | 1 +
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf | 42 +
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf | 52 +
Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h | 26 +
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h | 26 +
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h | 26 +
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h | 95 ++
Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.h | 6 +
Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h | 46 +
Silicon/Marvell/Include/Library/ArmadaSoCDescLib.h | 20 +
Silicon/Marvell/Include/Library/MvGpioLib.h | 1 +
Silicon/Marvell/Include/Protocol/BoardDesc.h | 22 +
Platform/Marvell/Armada70x0Db/Armada70x0DbBoardDescLib/Armada70x0DbBoardDescLib.c | 48 +
Platform/Marvell/Armada70x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 4 +
Platform/Marvell/Armada80x0Db/Armada80x0DbBoardDescLib/Armada80x0DbBoardDescLib.c | 48 +
Platform/Marvell/Armada80x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 6 +
Platform/SolidRun/Armada80x0McBin/Armada80x0McBinBoardDescLib/Armada80x0McBinBoardDescLib.c | 54 +
Platform/SolidRun/Armada80x0McBin/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 1 +
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c | 1531 ++++++++++++++++++++
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c | 265 ++++
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c | 345 +++++
Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.c | 44 +
Silicon/Marvell/Drivers/BoardDesc/MvBoardDescDxe.c | 86 ++
Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Dsdt.asl | 108 ++
Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc | 47 +
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Dsdt.asl | 108 ++
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc | 47 +
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Dsdt.asl | 108 ++
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc | 47 +
Silicon/Marvell/Armada7k8k/DeviceTree/armada-8040-mcbin.dts | 3 +
37 files changed, 3290 insertions(+), 11 deletions(-)
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc
--
2.7.4
^ permalink raw reply [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 01/14] Marvell/Library: MvGpioLib: Extend GPIO pin description
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 02/14] Marvell/Library: ArmadaSoCDescLib: Add PCIE information Marcin Wojtas
` (13 subsequent siblings)
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
In order to avoid hardcoding the controller type when using
MV_GPIO_PIN, extend this structure with new according field.
This patch is required to properly handle PCIE slot reset
with the GPIO pin.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Include/Library/MvGpioLib.h | 1 +
Platform/Marvell/Armada70x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 4 ++++
Platform/Marvell/Armada80x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 6 ++++++
Platform/SolidRun/Armada80x0McBin/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 1 +
4 files changed, 12 insertions(+)
diff --git a/Silicon/Marvell/Include/Library/MvGpioLib.h b/Silicon/Marvell/Include/Library/MvGpioLib.h
index 6ca9e79..35d979d 100644
--- a/Silicon/Marvell/Include/Library/MvGpioLib.h
+++ b/Silicon/Marvell/Include/Library/MvGpioLib.h
@@ -47,6 +47,7 @@ typedef struct {
} MV_GPIO_DEVICE_PATH;
typedef struct {
+ MV_GPIO_DRIVER_TYPE ControllerType;
UINTN ControllerId;
UINTN PinNumber;
BOOLEAN ActiveHigh;
diff --git a/Platform/Marvell/Armada70x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c b/Platform/Marvell/Armada70x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c
index 554155e..92a14bb 100644
--- a/Platform/Marvell/Armada70x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c
+++ b/Platform/Marvell/Armada70x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c
@@ -23,21 +23,25 @@
STATIC CONST MV_GPIO_PIN mXhciVbusPins[] = {
{
+ MV_GPIO_DRIVER_TYPE_PCA95XX,
ARMADA_70x0_DB_IO_EXPANDER0,
ARMADA_70x0_DB_VBUS0_PIN,
TRUE,
},
{
+ MV_GPIO_DRIVER_TYPE_PCA95XX,
ARMADA_70x0_DB_IO_EXPANDER0,
ARMADA_70x0_DB_VBUS0_LIMIT_PIN,
TRUE,
},
{
+ MV_GPIO_DRIVER_TYPE_PCA95XX,
ARMADA_70x0_DB_IO_EXPANDER0,
ARMADA_70x0_DB_VBUS1_PIN,
TRUE,
},
{
+ MV_GPIO_DRIVER_TYPE_PCA95XX,
ARMADA_70x0_DB_IO_EXPANDER0,
ARMADA_70x0_DB_VBUS1_LIMIT_PIN,
TRUE,
diff --git a/Platform/Marvell/Armada80x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c b/Platform/Marvell/Armada80x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c
index 804339f..cde73dd 100644
--- a/Platform/Marvell/Armada80x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c
+++ b/Platform/Marvell/Armada80x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c
@@ -23,31 +23,37 @@
STATIC CONST MV_GPIO_PIN mXhciVbusPins[] = {
{
+ MV_GPIO_DRIVER_TYPE_PCA95XX,
ARMADA_80x0_DB_IO_EXPANDER0,
ARMADA_80x0_DB_VBUS0_PIN,
TRUE,
},
{
+ MV_GPIO_DRIVER_TYPE_PCA95XX,
ARMADA_80x0_DB_IO_EXPANDER0,
ARMADA_80x0_DB_VBUS0_LIMIT_PIN,
TRUE,
},
{
+ MV_GPIO_DRIVER_TYPE_PCA95XX,
ARMADA_80x0_DB_IO_EXPANDER0,
ARMADA_80x0_DB_VBUS1_PIN,
TRUE,
},
{
+ MV_GPIO_DRIVER_TYPE_PCA95XX,
ARMADA_80x0_DB_IO_EXPANDER0,
ARMADA_80x0_DB_VBUS1_LIMIT_PIN,
TRUE,
},
{
+ MV_GPIO_DRIVER_TYPE_PCA95XX,
ARMADA_80x0_DB_IO_EXPANDER1,
ARMADA_80x0_DB_VBUS2_PIN,
TRUE,
},
{
+ MV_GPIO_DRIVER_TYPE_PCA95XX,
ARMADA_80x0_DB_IO_EXPANDER1,
ARMADA_80x0_DB_VBUS2_LIMIT_PIN,
TRUE,
diff --git a/Platform/SolidRun/Armada80x0McBin/NonDiscoverableInitLib/NonDiscoverableInitLib.c b/Platform/SolidRun/Armada80x0McBin/NonDiscoverableInitLib/NonDiscoverableInitLib.c
index c9e8872..f4e7246 100644
--- a/Platform/SolidRun/Armada80x0McBin/NonDiscoverableInitLib/NonDiscoverableInitLib.c
+++ b/Platform/SolidRun/Armada80x0McBin/NonDiscoverableInitLib/NonDiscoverableInitLib.c
@@ -22,6 +22,7 @@
#include "NonDiscoverableInitLib.h"
STATIC CONST MV_GPIO_PIN mXhciVbusPin = {
+ MV_GPIO_DRIVER_TYPE_SOC_CONTROLLER,
MV_GPIO_CP0_CONTROLLER1,
ARMADA_80x0_MCBIN_VBUS0_PIN,
TRUE,
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 02/14] Marvell/Library: ArmadaSoCDescLib: Add PCIE information
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 01/14] Marvell/Library: MvGpioLib: Extend GPIO pin description Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 03/14] Marvell/Library: ArmadaBoardDescLib: " Marcin Wojtas
` (12 subsequent siblings)
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
This patch introduces new library callback (ArmadaSoCPcieGet ()),
which dynamically allocates and fills array with all available PCIE
controllers' base addresses. It is needed for the configuration of PCIE,
whose support will be added in the upcoming patches.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.h | 6 +++
Silicon/Marvell/Include/Library/ArmadaSoCDescLib.h | 20 +++++++++
Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.c | 44 ++++++++++++++++++++
3 files changed, 70 insertions(+)
diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.h b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.h
index 74883fd..0296d43 100644
--- a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.h
+++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.h
@@ -76,6 +76,12 @@
#define MV_SOC_MDIO_ID(Cp) (Cp)
//
+// Platform description of PCIE
+//
+#define MV_SOC_PCIE_PER_CP_COUNT 3
+#define MV_SOC_PCIE_BASE(Index) (0x600000 + ((Index) * 0x20000))
+
+//
// Platform description of PP2 NIC
//
#define MV_SOC_PP2_BASE(Cp) MV_SOC_CP_BASE (Cp)
diff --git a/Silicon/Marvell/Include/Library/ArmadaSoCDescLib.h b/Silicon/Marvell/Include/Library/ArmadaSoCDescLib.h
index cd9c9f2..6432916 100644
--- a/Silicon/Marvell/Include/Library/ArmadaSoCDescLib.h
+++ b/Silicon/Marvell/Include/Library/ArmadaSoCDescLib.h
@@ -185,6 +185,26 @@ ArmadaSoCDescXhciGet (
IN OUT UINTN *DescCount
);
+/**
+ This function returns the total number of PCIE controllers and an array
+ with their base addresses.
+
+ @param[in out] **PcieDbiAddresses Array containing PCIE controllers' base
+ adresses.
+ @param[in out] *Count Total amount of available PCIE controllers.
+
+ @retval EFI_SUCCESS The data were obtained successfully.
+ @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a
+ lack of resources.
+
+**/
+EFI_STATUS
+EFIAPI
+ArmadaSoCPcieGet (
+ IN OUT EFI_PHYSICAL_ADDRESS **PcieDbiAddresses,
+ IN OUT UINTN *Count
+ );
+
//
// PP2 NIC devices SoC description
//
diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.c b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.c
index b637966..5947601 100644
--- a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.c
+++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.c
@@ -272,6 +272,50 @@ ArmadaSoCDescAhciGet (
return EFI_SUCCESS;
}
+/**
+ This function returns the total number of PCIE controllers and an array
+ with their base addresses.
+
+ @param[in out] **PcieBaseAddresses Array containing PCIE controllers' base
+ adresses.
+ @param[in out] *Count Total amount of available PCIE controllers.
+
+ @retval EFI_SUCCESS The data were obtained successfully.
+ @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a
+ lack of resources.
+
+**/
+EFI_STATUS
+EFIAPI
+ArmadaSoCPcieGet (
+ IN OUT EFI_PHYSICAL_ADDRESS **PcieBaseAddresses,
+ IN OUT UINTN *Count
+ )
+{
+ UINTN CpCount, CpIndex, Index;
+ EFI_PHYSICAL_ADDRESS *BaseAddress;
+
+ CpCount = FixedPcdGet8 (PcdMaxCpCount);
+
+ *Count = CpCount * MV_SOC_PCIE_PER_CP_COUNT;
+ BaseAddress = AllocateZeroPool (*Count * sizeof (EFI_PHYSICAL_ADDRESS));
+ if (BaseAddress == NULL) {
+ DEBUG ((DEBUG_ERROR, "%a: Cannot allocate memory\n", __FUNCTION__));
+ return EFI_OUT_OF_RESOURCES;
+ }
+
+ *PcieBaseAddresses = BaseAddress;
+
+ for (CpIndex = 0; CpIndex < CpCount; CpIndex++) {
+ for (Index = 0; Index < MV_SOC_PCIE_PER_CP_COUNT; Index++) {
+ *BaseAddress = MV_SOC_CP_BASE (CpIndex) + MV_SOC_PCIE_BASE (Index);
+ BaseAddress++;
+ }
+ }
+
+ return EFI_SUCCESS;
+}
+
EFI_STATUS
EFIAPI
ArmadaSoCDescPp2Get (
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 03/14] Marvell/Library: ArmadaBoardDescLib: Add PCIE information
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 01/14] Marvell/Library: MvGpioLib: Extend GPIO pin description Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 02/14] Marvell/Library: ArmadaSoCDescLib: Add PCIE information Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 04/14] Marvell/Armada7k8k: Extend board description libraries with PCIE Marcin Wojtas
` (11 subsequent siblings)
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
Introduce new callback that can provide information
about PCIE controller per-board description.
A new structure is defined containing base addresses,
windows/bus configuration and reset GPIO usage indication.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h | 46 ++++++++++++++++++++
1 file changed, 46 insertions(+)
diff --git a/Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h b/Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h
index a6d39c4..2ad19aa 100644
--- a/Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h
+++ b/Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h
@@ -9,6 +9,7 @@
#define __ARMADA_BOARD_DESC_LIB_H__
#include <Library/ArmadaSoCDescLib.h>
+#include <Library/MvGpioLib.h>
//
// COMPHY controllers per-board description
@@ -105,6 +106,51 @@ typedef struct {
} MV_BOARD_XHCI_DESC;
//
+// PCIE controllers description
+//
+typedef struct {
+ EFI_PHYSICAL_ADDRESS PcieDbiAddress;
+ EFI_PHYSICAL_ADDRESS ConfigSpaceAddress;
+ BOOLEAN HaveResetGpio;
+ MV_GPIO_PIN PcieResetGpio;
+ UINT64 PcieBusMin;
+ UINT64 PcieBusMax;
+ UINT64 PcieIoTranslation;
+ UINT64 PcieIoWinBase;
+ UINT64 PcieIoWinSize;
+ UINT64 PcieMmio32Translation;
+ UINT64 PcieMmio32WinBase;
+ UINT64 PcieMmio32WinSize;
+ UINT64 PcieMmio64Translation;
+ UINT64 PcieMmio64WinBase;
+ UINT64 PcieMmio64WinSize;
+} MV_PCIE_CONTROLLER;
+
+typedef struct {
+ MV_PCIE_CONTROLLER CONST *PcieControllers;
+ UINTN PcieControllerCount;
+} MV_BOARD_PCIE_DESCRIPTION;
+
+/**
+ Return the number and description of PCIE controllers used on the platform.
+
+ @param[in out] **PcieControllers Array containing PCIE controllers'
+ description.
+ @param[in out] *PcieControllerCount Amount of used PCIE controllers.
+
+ @retval EFI_SUCCESS The data were obtained successfully.
+ @retval EFI_NOT_FOUND None of the controllers is used.
+ @retval other Return error status.
+
+**/
+EFI_STATUS
+EFIAPI
+ArmadaBoardPcieControllerGet (
+ IN OUT MV_PCIE_CONTROLLER CONST **PcieControllers,
+ IN OUT UINTN *PcieControllerCount
+ );
+
+//
// PP2 NIC devices per-board description
//
typedef struct {
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 04/14] Marvell/Armada7k8k: Extend board description libraries with PCIE
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (2 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 03/14] Marvell/Library: ArmadaBoardDescLib: " Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 05/14] Marvell/Armada7k8k: MvBoardDesc: Extend protocol with PCIE support Marcin Wojtas
` (10 subsequent siblings)
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
This patch extends ArmadaBoardDescLib libraries for all
existing Armada7k8k-based platforms with PCIE.
It introduces ArmadaBoardPcieControllerGet routine with
per-board PCIE controllers description.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Platform/Marvell/Armada70x0Db/Armada70x0DbBoardDescLib/Armada70x0DbBoardDescLib.c | 48 +++++++++++++++++
Platform/Marvell/Armada80x0Db/Armada80x0DbBoardDescLib/Armada80x0DbBoardDescLib.c | 48 +++++++++++++++++
Platform/SolidRun/Armada80x0McBin/Armada80x0McBinBoardDescLib/Armada80x0McBinBoardDescLib.c | 54 ++++++++++++++++++++
3 files changed, 150 insertions(+)
diff --git a/Platform/Marvell/Armada70x0Db/Armada70x0DbBoardDescLib/Armada70x0DbBoardDescLib.c b/Platform/Marvell/Armada70x0Db/Armada70x0DbBoardDescLib/Armada70x0DbBoardDescLib.c
index dbd434f..ae13e0a 100644
--- a/Platform/Marvell/Armada70x0Db/Armada70x0DbBoardDescLib/Armada70x0DbBoardDescLib.c
+++ b/Platform/Marvell/Armada70x0Db/Armada70x0DbBoardDescLib/Armada70x0DbBoardDescLib.c
@@ -40,6 +40,54 @@ ArmadaBoardGpioExpanderGet (
}
//
+// PCIE
+//
+STATIC
+MV_PCIE_CONTROLLER mPcieController[] = {
+ { /* PCIE2 @0xF2640000 */
+ .PcieDbiAddress = 0xF2640000,
+ .ConfigSpaceAddress = 0xE0000000,
+ .HaveResetGpio = FALSE,
+ .PcieResetGpio = { 0 },
+ .PcieBusMin = 0,
+ .PcieBusMax = 0xFE,
+ .PcieIoTranslation = 0xEFF00000,
+ .PcieIoWinBase = 0x0,
+ .PcieIoWinSize = 0x10000,
+ .PcieMmio32Translation = 0,
+ .PcieMmio32WinBase = 0xC0000000,
+ .PcieMmio32WinSize = 0x20000000,
+ .PcieMmio64Translation = 0,
+ .PcieMmio64WinBase = 0x800000000,
+ .PcieMmio64WinSize = 0x100000000,
+ }
+};
+
+/**
+ Return the number and description of PCIE controllers used on the platform.
+
+ @param[in out] **PcieControllers Array containing PCIE controllers'
+ description.
+ @param[in out] *PcieControllerCount Amount of used PCIE controllers.
+
+ @retval EFI_SUCCESS The data were obtained successfully.
+ @retval other Return error status.
+
+**/
+EFI_STATUS
+EFIAPI
+ArmadaBoardPcieControllerGet (
+ IN OUT MV_PCIE_CONTROLLER CONST **PcieControllers,
+ IN OUT UINTN *PcieControllerCount
+ )
+{
+ *PcieControllers = mPcieController;
+ *PcieControllerCount = ARRAY_SIZE (mPcieController);
+
+ return EFI_SUCCESS;
+}
+
+//
// Order of devices in SdMmcDescTemplate has to be in par with ArmadaSoCDescLib
//
STATIC
diff --git a/Platform/Marvell/Armada80x0Db/Armada80x0DbBoardDescLib/Armada80x0DbBoardDescLib.c b/Platform/Marvell/Armada80x0Db/Armada80x0DbBoardDescLib/Armada80x0DbBoardDescLib.c
index f083c94..144009c 100644
--- a/Platform/Marvell/Armada80x0Db/Armada80x0DbBoardDescLib/Armada80x0DbBoardDescLib.c
+++ b/Platform/Marvell/Armada80x0Db/Armada80x0DbBoardDescLib/Armada80x0DbBoardDescLib.c
@@ -46,6 +46,54 @@ ArmadaBoardGpioExpanderGet (
}
//
+// PCIE
+//
+STATIC
+MV_PCIE_CONTROLLER mPcieController[] = {
+ { /* PCIE0 @0xF2600000 */
+ .PcieDbiAddress = 0xF2600000,
+ .ConfigSpaceAddress = 0xE0000000,
+ .HaveResetGpio = FALSE,
+ .PcieResetGpio = { 0 },
+ .PcieBusMin = 0,
+ .PcieBusMax = 0xFE,
+ .PcieIoTranslation = 0xEFF00000,
+ .PcieIoWinBase = 0x0,
+ .PcieIoWinSize = 0x10000,
+ .PcieMmio32Translation = 0,
+ .PcieMmio32WinBase = 0xC0000000,
+ .PcieMmio32WinSize = 0x20000000,
+ .PcieMmio64Translation = 0,
+ .PcieMmio64WinBase = 0x800000000,
+ .PcieMmio64WinSize = 0x100000000,
+ }
+};
+
+/**
+ Return the number and description of PCIE controllers used on the platform.
+
+ @param[in out] **PcieControllers Array containing PCIE controllers'
+ description.
+ @param[in out] *PcieControllerCount Amount of used PCIE controllers.
+
+ @retval EFI_SUCCESS The data were obtained successfully.
+ @retval other Return error status.
+
+**/
+EFI_STATUS
+EFIAPI
+ArmadaBoardPcieControllerGet (
+ IN OUT MV_PCIE_CONTROLLER CONST **PcieControllers,
+ IN OUT UINTN *PcieControllerCount
+ )
+{
+ *PcieControllers = mPcieController;
+ *PcieControllerCount = ARRAY_SIZE (mPcieController);
+
+ return EFI_SUCCESS;
+}
+
+//
// Order of devices in SdMmcDescTemplate has to be in par with ArmadaSoCDescLib
//
STATIC
diff --git a/Platform/SolidRun/Armada80x0McBin/Armada80x0McBinBoardDescLib/Armada80x0McBinBoardDescLib.c b/Platform/SolidRun/Armada80x0McBin/Armada80x0McBinBoardDescLib/Armada80x0McBinBoardDescLib.c
index 3b69074..ebe7386 100644
--- a/Platform/SolidRun/Armada80x0McBin/Armada80x0McBinBoardDescLib/Armada80x0McBinBoardDescLib.c
+++ b/Platform/SolidRun/Armada80x0McBin/Armada80x0McBinBoardDescLib/Armada80x0McBinBoardDescLib.c
@@ -33,6 +33,60 @@ ArmadaBoardGpioExpanderGet (
}
//
+// PCIE
+//
+STATIC
+MV_PCIE_CONTROLLER mPcieController[] = {
+ { /* PCIE0 @0xF2600000 */
+ .PcieDbiAddress = 0xF2600000,
+ .ConfigSpaceAddress = 0xE0000000,
+ .HaveResetGpio = TRUE,
+ .PcieResetGpio =
+ {
+ MV_GPIO_DRIVER_TYPE_SOC_CONTROLLER,
+ MV_GPIO_CP0_CONTROLLER1,
+ 20,
+ FALSE
+ },
+ .PcieBusMin = 0,
+ .PcieBusMax = 0xFE,
+ .PcieIoTranslation = 0xEFF00000,
+ .PcieIoWinBase = 0x0,
+ .PcieIoWinSize = 0x10000,
+ .PcieMmio32Translation = 0,
+ .PcieMmio32WinBase = 0xC0000000,
+ .PcieMmio32WinSize = 0x20000000,
+ .PcieMmio64Translation = 0,
+ .PcieMmio64WinBase = 0x800000000,
+ .PcieMmio64WinSize = 0x100000000,
+ }
+};
+
+/**
+ Return the number and description of PCIE controllers used on the platform.
+
+ @param[in out] **PcieControllers Array containing PCIE controllers'
+ description.
+ @param[in out] *PcieControllerCount Amount of used PCIE controllers.
+
+ @retval EFI_SUCCESS The data were obtained successfully.
+ @retval other Return error status.
+
+**/
+EFI_STATUS
+EFIAPI
+ArmadaBoardPcieControllerGet (
+ IN OUT MV_PCIE_CONTROLLER CONST **PcieControllers,
+ IN OUT UINTN *PcieControllerCount
+ )
+{
+ *PcieControllers = mPcieController;
+ *PcieControllerCount = ARRAY_SIZE (mPcieController);
+
+ return EFI_SUCCESS;
+}
+
+//
// Order of devices in SdMmcDescTemplate has to be in par with ArmadaSoCDescLib
//
STATIC
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 05/14] Marvell/Armada7k8k: MvBoardDesc: Extend protocol with PCIE support
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (3 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 04/14] Marvell/Armada7k8k: Extend board description libraries with PCIE Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation Marcin Wojtas
` (9 subsequent siblings)
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
Introduce new callback that can provide information about PCIE
controllers, which are used on the platform. According ArmadaSoCDescLib
ArmadaBoardDescLib routines are used for obtaining required data.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Include/Protocol/BoardDesc.h | 22 +++++
Silicon/Marvell/Drivers/BoardDesc/MvBoardDescDxe.c | 86 ++++++++++++++++++++
2 files changed, 108 insertions(+)
diff --git a/Silicon/Marvell/Include/Protocol/BoardDesc.h b/Silicon/Marvell/Include/Protocol/BoardDesc.h
index 02905ea..48f6d9d 100644
--- a/Silicon/Marvell/Include/Protocol/BoardDesc.h
+++ b/Silicon/Marvell/Include/Protocol/BoardDesc.h
@@ -90,6 +90,27 @@ EFI_STATUS
IN OUT MV_BOARD_XHCI_DESC **XhciDesc
);
+/**
+ Return the description of PCIE controllers used on the platform.
+
+ @param[in out] *This Pointer to board description protocol.
+ @param[in out] **PcieDescription Array containing PCIE controllers'
+ description.
+
+ @retval EFI_SUCCESS The data were obtained successfully.
+ @retval EFI_NOT_FOUND None of the controllers is used.
+ @retval EFI_INVALID_PARAMETER Description wrongly defined.
+ @retval EFI_OUT_OF_RESOURCES Lack of resources.
+ @retval Other Return error status.
+
+**/
+typedef
+EFI_STATUS
+(EFIAPI *MV_BOARD_PCIE_DESCRIPTION_GET) (
+ IN MARVELL_BOARD_DESC_PROTOCOL *This,
+ IN OUT MV_BOARD_PCIE_DESCRIPTION CONST **PcieDescription
+ );
+
typedef
EFI_STATUS
(EFIAPI *MV_BOARD_DESC_PP2_GET) (
@@ -121,6 +142,7 @@ struct _MARVELL_BOARD_DESC_PROTOCOL {
MV_BOARD_DESC_XHCI_GET BoardDescXhciGet;
MV_BOARD_DESC_FREE BoardDescFree;
MV_BOARD_GPIO_DESCRIPTION_GET GpioDescriptionGet;
+ MV_BOARD_PCIE_DESCRIPTION_GET PcieDescriptionGet;
};
#endif // __MARVELL_BOARD_DESC_PROTOCOL_H__
diff --git a/Silicon/Marvell/Drivers/BoardDesc/MvBoardDescDxe.c b/Silicon/Marvell/Drivers/BoardDesc/MvBoardDescDxe.c
index 973c362..042db28 100644
--- a/Silicon/Marvell/Drivers/BoardDesc/MvBoardDescDxe.c
+++ b/Silicon/Marvell/Drivers/BoardDesc/MvBoardDescDxe.c
@@ -36,6 +36,7 @@ SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
MV_BOARD_DESC *mBoardDescInstance;
STATIC MV_BOARD_GPIO_DESCRIPTION *mGpioDescription;
+STATIC MV_BOARD_PCIE_DESCRIPTION *mPcieDescription;
STATIC
EFI_STATUS
@@ -444,6 +445,90 @@ MvBoardDescXhciGet (
return EFI_SUCCESS;
}
+/**
+ Return the description of PCIE controllers used on the platform.
+
+ @param[in out] *This Pointer to board description protocol.
+ @param[in out] **PcieDescription Array containing PCIE controllers'
+ description.
+
+ @retval EFI_SUCCESS The data were obtained successfully.
+ @retval EFI_NOT_FOUND None of the controllers is used.
+ @retval EFI_INVALID_PARAMETER Description wrongly defined.
+ @retval EFI_OUT_OF_RESOURCES Lack of resources.
+ @retval Other Return error status.
+
+**/
+STATIC
+EFI_STATUS
+MvBoardPcieDescriptionGet (
+ IN MARVELL_BOARD_DESC_PROTOCOL *This,
+ IN OUT MV_BOARD_PCIE_DESCRIPTION CONST **PcieDescription
+ )
+{
+ UINTN SoCPcieControllerCount, BoardPcieControllerCount, SoCIndex, BoardIndex;
+ EFI_PHYSICAL_ADDRESS *PcieDbiAddresses;
+ MV_PCIE_CONTROLLER CONST *PcieControllers;
+ EFI_STATUS Status;
+
+ /* Use existing structure if already created. */
+ if (mPcieDescription != NULL) {
+ *PcieDescription = mPcieDescription;
+ return EFI_SUCCESS;
+ }
+
+ /* Get SoC data about all available PCIE controllers. */
+ Status = ArmadaSoCPcieGet (&PcieDbiAddresses, &SoCPcieControllerCount);
+ if (EFI_ERROR (Status)) {
+ return Status;
+ }
+
+ /* Get per-board information about all used PCIE controllers. */
+ Status = ArmadaBoardPcieControllerGet (&PcieControllers,
+ &BoardPcieControllerCount);
+ if (EFI_ERROR (Status)) {
+ return Status;
+ }
+
+ /* Sanity check of the board description. */
+ if (BoardPcieControllerCount > SoCPcieControllerCount) {
+ DEBUG ((DEBUG_ERROR, "%a: Too many controllers described\n", __FUNCTION__));
+ return EFI_INVALID_PARAMETER;
+ }
+
+ for (BoardIndex = 0; BoardIndex < BoardPcieControllerCount; BoardIndex++) {
+ for (SoCIndex = 0; SoCIndex < SoCPcieControllerCount; SoCIndex++) {
+ if (PcieControllers[BoardIndex].PcieDbiAddress ==
+ PcieDbiAddresses[SoCIndex]) {
+ /* Match found */
+ break;
+ }
+ }
+ if (SoCIndex == SoCPcieControllerCount) {
+ DEBUG ((DEBUG_ERROR,
+ "%a: Controller #%d base address invalid: 0x%x\n",
+ __FUNCTION__,
+ BoardIndex,
+ PcieControllers[BoardIndex].PcieDbiAddress));
+ return EFI_INVALID_PARAMETER;
+ }
+ }
+
+ /* Allocate and fill board description. */
+ mPcieDescription = AllocateZeroPool (sizeof (MV_BOARD_PCIE_DESCRIPTION));
+ if (mPcieDescription == NULL) {
+ DEBUG ((DEBUG_ERROR, "%a: Cannot allocate memory\n", __FUNCTION__));
+ return EFI_OUT_OF_RESOURCES;
+ }
+
+ mPcieDescription->PcieControllers = PcieControllers;
+ mPcieDescription->PcieControllerCount = BoardPcieControllerCount;
+
+ *PcieDescription = mPcieDescription;
+
+ return EFI_SUCCESS;
+}
+
STATIC
EFI_STATUS
MvBoardDescPp2Get (
@@ -621,6 +706,7 @@ MvBoardDescInitProtocol (
BoardDescProtocol->BoardDescXhciGet = MvBoardDescXhciGet;
BoardDescProtocol->BoardDescFree = MvBoardDescFree;
BoardDescProtocol->GpioDescriptionGet = MvBoardGpioDescriptionGet;
+ BoardDescProtocol->PcieDescriptionGet = MvBoardPcieDescriptionGet;
return EFI_SUCCESS;
}
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (4 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 05/14] Marvell/Armada7k8k: MvBoardDesc: Extend protocol with PCIE support Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-24 12:50 ` Ard Biesheuvel
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 07/14] Marvell/Armada7k8k: Implement PciHostBridgeLib Marcin Wojtas
` (8 subsequent siblings)
14 siblings, 1 reply; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
From: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Implement a special version of PciExpressLib that takes the quirky
nature of the Synopsys Designware PCIe IP into account. In particular,
we need to ignore config space accesses to all devices on the first
bus except device 0, because the broadcast nature of type 0 configuration
cycles will result in whatever device is in the slot to appear at each
of the 32 device positions.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf | 42 +
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c | 1531 ++++++++++++++++++++
2 files changed, 1573 insertions(+)
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
new file mode 100644
index 0000000..a66ef28
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
@@ -0,0 +1,42 @@
+## @file
+#
+# Copyright (c) 2017, Linaro, Ltd. All rights reserved.<BR>
+# Copyright (c) 2019, Marvell International Ltd. All rights reserved.<BR>
+#
+# This program and the accompanying materials
+# are licensed and made available under the terms and conditions of the BSD License
+# which accompanies this distribution. The full text of the license may be found at
+# http://opensource.org/licenses/bsd-license.php.
+# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+#
+#
+##
+
+[Defines]
+ INF_VERSION = 0x0001001B
+ BASE_NAME = Armada7k8kPciExpressLib
+ FILE_GUID = f0926204-3061-40ed-8261-2aeccc7914c9
+ MODULE_TYPE = BASE
+ VERSION_STRING = 1.0
+ LIBRARY_CLASS = PciExpressLib
+
+[Sources]
+ PciExpressLib.c
+
+[Packages]
+ ArmPkg/ArmPkg.dec
+ MdePkg/MdePkg.dec
+
+[LibraryClasses]
+ BaseLib
+ DebugLib
+ IoLib
+ PcdLib
+
+[Pcd]
+ gEfiMdePkgTokenSpaceGuid.PcdPciExpressBaseAddress ## CONSUMES
+
+[FixedPcd]
+ gArmTokenSpaceGuid.PcdPciBusMin
+ gArmTokenSpaceGuid.PcdPciBusMax
diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
new file mode 100644
index 0000000..e88cc7b
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
@@ -0,0 +1,1531 @@
+/** @file
+
+ Copyright (c) 2006 - 2012, Intel Corporation. All rights reserved.<BR>
+ Copyright (c) 2017, Linaro, Ltd. All rights reserved.<BR>
+ Copyright (c) 2019, Marvell International Ltd. All rights reserved.<BR>
+
+ This program and the accompanying materials
+ are licensed and made available under the terms and conditions of the BSD License
+ which accompanies this distribution. The full text of the license may be found at
+ http://opensource.org/licenses/bsd-license.php.
+
+ THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+ WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+
+
+#include <Base.h>
+
+#include <Library/BaseLib.h>
+#include <Library/DebugLib.h>
+#include <Library/IoLib.h>
+#include <Library/PcdLib.h>
+#include <Library/PciExpressLib.h>
+
+/**
+ Assert the validity of a PCI address. A valid PCI address should contain 1's
+ only in the low 28 bits.
+
+ @param A The address to validate.
+
+**/
+#define ASSERT_INVALID_PCI_ADDRESS(A) \
+ ASSERT (((A) & ~0xfffffff) == 0)
+
+/**
+ Registers a PCI device so PCI configuration registers may be accessed after
+ SetVirtualAddressMap().
+
+ Registers the PCI device specified by Address so all the PCI configuration
+ registers associated with that PCI device may be accessed after SetVirtualAddressMap()
+ is called.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+
+ @retval RETURN_SUCCESS The PCI device was registered for runtime access.
+ @retval RETURN_UNSUPPORTED An attempt was made to call this function
+ after ExitBootServices().
+ @retval RETURN_UNSUPPORTED The resources required to access the PCI device
+ at runtime could not be mapped.
+ @retval RETURN_OUT_OF_RESOURCES There are not enough resources available to
+ complete the registration.
+
+**/
+RETURN_STATUS
+EFIAPI
+PciExpressRegisterForRuntimeAccess (
+ IN UINTN Address
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ return RETURN_UNSUPPORTED;
+}
+
+#define ECAM_BUS_SIZE SIZE_1MB
+#define ECAM_DEV_SIZE SIZE_32KB
+
+STATIC
+BOOLEAN
+IgnoreBusDeviceFunction (
+ IN UINTN Address
+ )
+{
+ ASSERT (Address >= FixedPcdGet32 (PcdPciBusMin) * ECAM_BUS_SIZE);
+ ASSERT (Address < (FixedPcdGet32 (PcdPciBusMax) + 1) * ECAM_BUS_SIZE);
+
+ //
+ // Type 0 configuration cycles contain a b/d/f specifier, however
+ // the endpoint is unaware of its own device number and responds to all
+ // of them. The bus is responsible to ensure for assigning proper
+ // device/function. Sadly, the Synopsys IP does not implement this,
+ // and so we have to ignore config space accesses for all devices on the
+ // first bus except device 0.
+ //
+ return (Address >= (FixedPcdGet32 (PcdPciBusMin) * ECAM_BUS_SIZE +
+ ECAM_DEV_SIZE) &&
+ Address < (FixedPcdGet32 (PcdPciBusMin) + 1) * ECAM_BUS_SIZE);
+}
+
+/**
+ Gets the base address of PCI Express.
+
+ This internal functions retrieves PCI Express Base Address via a PCD entry
+ PcdPciExpressBaseAddress.
+
+ @return The base address of PCI Express.
+
+**/
+VOID *
+GetPciExpressBaseAddress (
+ VOID
+ )
+{
+ return (VOID *)(UINTN)PcdGet64 (PcdPciExpressBaseAddress);
+}
+
+/**
+ Reads an 8-bit PCI configuration register.
+
+ Reads and returns the 8-bit PCI configuration register specified by Address.
+ This function must guarantee that all PCI read and write operations are
+ serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+
+ @return The read value from the PCI configuration register.
+
+**/
+UINT8
+EFIAPI
+PciExpressRead8 (
+ IN UINTN Address
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT8;
+ }
+ return MmioRead8 ((UINTN)GetPciExpressBaseAddress () + Address);
+}
+
+/**
+ Writes an 8-bit PCI configuration register.
+
+ Writes the 8-bit PCI configuration register specified by Address with the
+ value specified by Value. Value is returned. This function must guarantee
+ that all PCI read and write operations are serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param Value The value to write.
+
+ @return The value written to the PCI configuration register.
+
+**/
+UINT8
+EFIAPI
+PciExpressWrite8 (
+ IN UINTN Address,
+ IN UINT8 Value
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT8;
+ }
+ return MmioWrite8 ((UINTN)GetPciExpressBaseAddress () + Address, Value);
+}
+
+/**
+ Performs a bitwise OR of an 8-bit PCI configuration register with
+ an 8-bit value.
+
+ Reads the 8-bit PCI configuration register specified by Address, performs a
+ bitwise OR between the read result and the value specified by
+ OrData, and writes the result to the 8-bit PCI configuration register
+ specified by Address. The value written to the PCI configuration register is
+ returned. This function must guarantee that all PCI read and write operations
+ are serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param OrData The value to OR with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT8
+EFIAPI
+PciExpressOr8 (
+ IN UINTN Address,
+ IN UINT8 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT8;
+ }
+ return MmioOr8 ((UINTN)GetPciExpressBaseAddress () + Address, OrData);
+}
+
+/**
+ Performs a bitwise AND of an 8-bit PCI configuration register with an 8-bit
+ value.
+
+ Reads the 8-bit PCI configuration register specified by Address, performs a
+ bitwise AND between the read result and the value specified by AndData, and
+ writes the result to the 8-bit PCI configuration register specified by
+ Address. The value written to the PCI configuration register is returned.
+ This function must guarantee that all PCI read and write operations are
+ serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param AndData The value to AND with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT8
+EFIAPI
+PciExpressAnd8 (
+ IN UINTN Address,
+ IN UINT8 AndData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT8;
+ }
+ return MmioAnd8 ((UINTN)GetPciExpressBaseAddress () + Address, AndData);
+}
+
+/**
+ Performs a bitwise AND of an 8-bit PCI configuration register with an 8-bit
+ value, followed a bitwise OR with another 8-bit value.
+
+ Reads the 8-bit PCI configuration register specified by Address, performs a
+ bitwise AND between the read result and the value specified by AndData,
+ performs a bitwise OR between the result of the AND operation and
+ the value specified by OrData, and writes the result to the 8-bit PCI
+ configuration register specified by Address. The value written to the PCI
+ configuration register is returned. This function must guarantee that all PCI
+ read and write operations are serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param AndData The value to AND with the PCI configuration register.
+ @param OrData The value to OR with the result of the AND operation.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT8
+EFIAPI
+PciExpressAndThenOr8 (
+ IN UINTN Address,
+ IN UINT8 AndData,
+ IN UINT8 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT8;
+ }
+ return MmioAndThenOr8 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ AndData,
+ OrData
+ );
+}
+
+/**
+ Reads a bit field of a PCI configuration register.
+
+ Reads the bit field in an 8-bit PCI configuration register. The bit field is
+ specified by the StartBit and the EndBit. The value of the bit field is
+ returned.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If StartBit is greater than 7, then ASSERT().
+ If EndBit is greater than 7, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+
+ @param Address The PCI configuration register to read.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..7.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..7.
+
+ @return The value of the bit field read from the PCI configuration register.
+
+**/
+UINT8
+EFIAPI
+PciExpressBitFieldRead8 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT8;
+ }
+ return MmioBitFieldRead8 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit
+ );
+}
+
+/**
+ Writes a bit field to a PCI configuration register.
+
+ Writes Value to the bit field of the PCI configuration register. The bit
+ field is specified by the StartBit and the EndBit. All other bits in the
+ destination PCI configuration register are preserved. The new value of the
+ 8-bit register is returned.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If StartBit is greater than 7, then ASSERT().
+ If EndBit is greater than 7, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If Value is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..7.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..7.
+ @param Value The new value of the bit field.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT8
+EFIAPI
+PciExpressBitFieldWrite8 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT8 Value
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT8;
+ }
+ return MmioBitFieldWrite8 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ Value
+ );
+}
+
+/**
+ Reads a bit field in an 8-bit PCI configuration, performs a bitwise OR, and
+ writes the result back to the bit field in the 8-bit port.
+
+ Reads the 8-bit PCI configuration register specified by Address, performs a
+ bitwise OR between the read result and the value specified by
+ OrData, and writes the result to the 8-bit PCI configuration register
+ specified by Address. The value written to the PCI configuration register is
+ returned. This function must guarantee that all PCI read and write operations
+ are serialized. Extra left bits in OrData are stripped.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If StartBit is greater than 7, then ASSERT().
+ If EndBit is greater than 7, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..7.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..7.
+ @param OrData The value to OR with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT8
+EFIAPI
+PciExpressBitFieldOr8 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT8 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT8;
+ }
+ return MmioBitFieldOr8 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ OrData
+ );
+}
+
+/**
+ Reads a bit field in an 8-bit PCI configuration register, performs a bitwise
+ AND, and writes the result back to the bit field in the 8-bit register.
+
+ Reads the 8-bit PCI configuration register specified by Address, performs a
+ bitwise AND between the read result and the value specified by AndData, and
+ writes the result to the 8-bit PCI configuration register specified by
+ Address. The value written to the PCI configuration register is returned.
+ This function must guarantee that all PCI read and write operations are
+ serialized. Extra left bits in AndData are stripped.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If StartBit is greater than 7, then ASSERT().
+ If EndBit is greater than 7, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..7.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..7.
+ @param AndData The value to AND with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT8
+EFIAPI
+PciExpressBitFieldAnd8 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT8 AndData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT8;
+ }
+ return MmioBitFieldAnd8 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ AndData
+ );
+}
+
+/**
+ Reads a bit field in an 8-bit port, performs a bitwise AND followed by a
+ bitwise OR, and writes the result back to the bit field in the
+ 8-bit port.
+
+ Reads the 8-bit PCI configuration register specified by Address, performs a
+ bitwise AND followed by a bitwise OR between the read result and
+ the value specified by AndData, and writes the result to the 8-bit PCI
+ configuration register specified by Address. The value written to the PCI
+ configuration register is returned. This function must guarantee that all PCI
+ read and write operations are serialized. Extra left bits in both AndData and
+ OrData are stripped.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If StartBit is greater than 7, then ASSERT().
+ If EndBit is greater than 7, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+ If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..7.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..7.
+ @param AndData The value to AND with the PCI configuration register.
+ @param OrData The value to OR with the result of the AND operation.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT8
+EFIAPI
+PciExpressBitFieldAndThenOr8 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT8 AndData,
+ IN UINT8 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT8;
+ }
+ return MmioBitFieldAndThenOr8 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ AndData,
+ OrData
+ );
+}
+
+/**
+ Reads a 16-bit PCI configuration register.
+
+ Reads and returns the 16-bit PCI configuration register specified by Address.
+ This function must guarantee that all PCI read and write operations are
+ serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 16-bit boundary, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+
+ @return The read value from the PCI configuration register.
+
+**/
+UINT16
+EFIAPI
+PciExpressRead16 (
+ IN UINTN Address
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT16;
+ }
+ return MmioRead16 ((UINTN)GetPciExpressBaseAddress () + Address);
+}
+
+/**
+ Writes a 16-bit PCI configuration register.
+
+ Writes the 16-bit PCI configuration register specified by Address with the
+ value specified by Value. Value is returned. This function must guarantee
+ that all PCI read and write operations are serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 16-bit boundary, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param Value The value to write.
+
+ @return The value written to the PCI configuration register.
+
+**/
+UINT16
+EFIAPI
+PciExpressWrite16 (
+ IN UINTN Address,
+ IN UINT16 Value
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT16;
+ }
+ return MmioWrite16 ((UINTN)GetPciExpressBaseAddress () + Address, Value);
+}
+
+/**
+ Performs a bitwise OR of a 16-bit PCI configuration register with
+ a 16-bit value.
+
+ Reads the 16-bit PCI configuration register specified by Address, performs a
+ bitwise OR between the read result and the value specified by
+ OrData, and writes the result to the 16-bit PCI configuration register
+ specified by Address. The value written to the PCI configuration register is
+ returned. This function must guarantee that all PCI read and write operations
+ are serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 16-bit boundary, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param OrData The value to OR with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT16
+EFIAPI
+PciExpressOr16 (
+ IN UINTN Address,
+ IN UINT16 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT16;
+ }
+ return MmioOr16 ((UINTN)GetPciExpressBaseAddress () + Address, OrData);
+}
+
+/**
+ Performs a bitwise AND of a 16-bit PCI configuration register with a 16-bit
+ value.
+
+ Reads the 16-bit PCI configuration register specified by Address, performs a
+ bitwise AND between the read result and the value specified by AndData, and
+ writes the result to the 16-bit PCI configuration register specified by
+ Address. The value written to the PCI configuration register is returned.
+ This function must guarantee that all PCI read and write operations are
+ serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 16-bit boundary, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param AndData The value to AND with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT16
+EFIAPI
+PciExpressAnd16 (
+ IN UINTN Address,
+ IN UINT16 AndData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT16;
+ }
+ return MmioAnd16 ((UINTN)GetPciExpressBaseAddress () + Address, AndData);
+}
+
+/**
+ Performs a bitwise AND of a 16-bit PCI configuration register with a 16-bit
+ value, followed a bitwise OR with another 16-bit value.
+
+ Reads the 16-bit PCI configuration register specified by Address, performs a
+ bitwise AND between the read result and the value specified by AndData,
+ performs a bitwise OR between the result of the AND operation and
+ the value specified by OrData, and writes the result to the 16-bit PCI
+ configuration register specified by Address. The value written to the PCI
+ configuration register is returned. This function must guarantee that all PCI
+ read and write operations are serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 16-bit boundary, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param AndData The value to AND with the PCI configuration register.
+ @param OrData The value to OR with the result of the AND operation.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT16
+EFIAPI
+PciExpressAndThenOr16 (
+ IN UINTN Address,
+ IN UINT16 AndData,
+ IN UINT16 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT16;
+ }
+ return MmioAndThenOr16 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ AndData,
+ OrData
+ );
+}
+
+/**
+ Reads a bit field of a PCI configuration register.
+
+ Reads the bit field in a 16-bit PCI configuration register. The bit field is
+ specified by the StartBit and the EndBit. The value of the bit field is
+ returned.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 16-bit boundary, then ASSERT().
+ If StartBit is greater than 15, then ASSERT().
+ If EndBit is greater than 15, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+
+ @param Address The PCI configuration register to read.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..15.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..15.
+
+ @return The value of the bit field read from the PCI configuration register.
+
+**/
+UINT16
+EFIAPI
+PciExpressBitFieldRead16 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT16;
+ }
+ return MmioBitFieldRead16 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit
+ );
+}
+
+/**
+ Writes a bit field to a PCI configuration register.
+
+ Writes Value to the bit field of the PCI configuration register. The bit
+ field is specified by the StartBit and the EndBit. All other bits in the
+ destination PCI configuration register are preserved. The new value of the
+ 16-bit register is returned.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 16-bit boundary, then ASSERT().
+ If StartBit is greater than 15, then ASSERT().
+ If EndBit is greater than 15, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If Value is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..15.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..15.
+ @param Value The new value of the bit field.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT16
+EFIAPI
+PciExpressBitFieldWrite16 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT16 Value
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT16;
+ }
+ return MmioBitFieldWrite16 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ Value
+ );
+}
+
+/**
+ Reads a bit field in a 16-bit PCI configuration, performs a bitwise OR, and
+ writes the result back to the bit field in the 16-bit port.
+
+ Reads the 16-bit PCI configuration register specified by Address, performs a
+ bitwise OR between the read result and the value specified by
+ OrData, and writes the result to the 16-bit PCI configuration register
+ specified by Address. The value written to the PCI configuration register is
+ returned. This function must guarantee that all PCI read and write operations
+ are serialized. Extra left bits in OrData are stripped.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 16-bit boundary, then ASSERT().
+ If StartBit is greater than 15, then ASSERT().
+ If EndBit is greater than 15, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..15.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..15.
+ @param OrData The value to OR with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT16
+EFIAPI
+PciExpressBitFieldOr16 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT16 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT16;
+ }
+ return MmioBitFieldOr16 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ OrData
+ );
+}
+
+/**
+ Reads a bit field in a 16-bit PCI configuration register, performs a bitwise
+ AND, and writes the result back to the bit field in the 16-bit register.
+
+ Reads the 16-bit PCI configuration register specified by Address, performs a
+ bitwise AND between the read result and the value specified by AndData, and
+ writes the result to the 16-bit PCI configuration register specified by
+ Address. The value written to the PCI configuration register is returned.
+ This function must guarantee that all PCI read and write operations are
+ serialized. Extra left bits in AndData are stripped.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 16-bit boundary, then ASSERT().
+ If StartBit is greater than 15, then ASSERT().
+ If EndBit is greater than 15, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..15.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..15.
+ @param AndData The value to AND with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT16
+EFIAPI
+PciExpressBitFieldAnd16 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT16 AndData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT16;
+ }
+ return MmioBitFieldAnd16 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ AndData
+ );
+}
+
+/**
+ Reads a bit field in a 16-bit port, performs a bitwise AND followed by a
+ bitwise OR, and writes the result back to the bit field in the
+ 16-bit port.
+
+ Reads the 16-bit PCI configuration register specified by Address, performs a
+ bitwise AND followed by a bitwise OR between the read result and
+ the value specified by AndData, and writes the result to the 16-bit PCI
+ configuration register specified by Address. The value written to the PCI
+ configuration register is returned. This function must guarantee that all PCI
+ read and write operations are serialized. Extra left bits in both AndData and
+ OrData are stripped.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 16-bit boundary, then ASSERT().
+ If StartBit is greater than 15, then ASSERT().
+ If EndBit is greater than 15, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+ If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..15.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..15.
+ @param AndData The value to AND with the PCI configuration register.
+ @param OrData The value to OR with the result of the AND operation.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT16
+EFIAPI
+PciExpressBitFieldAndThenOr16 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT16 AndData,
+ IN UINT16 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT16;
+ }
+ return MmioBitFieldAndThenOr16 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ AndData,
+ OrData
+ );
+}
+
+/**
+ Reads a 32-bit PCI configuration register.
+
+ Reads and returns the 32-bit PCI configuration register specified by Address.
+ This function must guarantee that all PCI read and write operations are
+ serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 32-bit boundary, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+
+ @return The read value from the PCI configuration register.
+
+**/
+UINT32
+EFIAPI
+PciExpressRead32 (
+ IN UINTN Address
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT32;
+ }
+ return MmioRead32 ((UINTN)GetPciExpressBaseAddress () + Address);
+}
+
+/**
+ Writes a 32-bit PCI configuration register.
+
+ Writes the 32-bit PCI configuration register specified by Address with the
+ value specified by Value. Value is returned. This function must guarantee
+ that all PCI read and write operations are serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 32-bit boundary, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param Value The value to write.
+
+ @return The value written to the PCI configuration register.
+
+**/
+UINT32
+EFIAPI
+PciExpressWrite32 (
+ IN UINTN Address,
+ IN UINT32 Value
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT32;
+ }
+ return MmioWrite32 ((UINTN)GetPciExpressBaseAddress () + Address, Value);
+}
+
+/**
+ Performs a bitwise OR of a 32-bit PCI configuration register with
+ a 32-bit value.
+
+ Reads the 32-bit PCI configuration register specified by Address, performs a
+ bitwise OR between the read result and the value specified by
+ OrData, and writes the result to the 32-bit PCI configuration register
+ specified by Address. The value written to the PCI configuration register is
+ returned. This function must guarantee that all PCI read and write operations
+ are serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 32-bit boundary, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param OrData The value to OR with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT32
+EFIAPI
+PciExpressOr32 (
+ IN UINTN Address,
+ IN UINT32 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT32;
+ }
+ return MmioOr32 ((UINTN)GetPciExpressBaseAddress () + Address, OrData);
+}
+
+/**
+ Performs a bitwise AND of a 32-bit PCI configuration register with a 32-bit
+ value.
+
+ Reads the 32-bit PCI configuration register specified by Address, performs a
+ bitwise AND between the read result and the value specified by AndData, and
+ writes the result to the 32-bit PCI configuration register specified by
+ Address. The value written to the PCI configuration register is returned.
+ This function must guarantee that all PCI read and write operations are
+ serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 32-bit boundary, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param AndData The value to AND with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT32
+EFIAPI
+PciExpressAnd32 (
+ IN UINTN Address,
+ IN UINT32 AndData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT32;
+ }
+return MmioAnd32 ((UINTN)GetPciExpressBaseAddress () + Address, AndData);
+}
+
+/**
+ Performs a bitwise AND of a 32-bit PCI configuration register with a 32-bit
+ value, followed a bitwise OR with another 32-bit value.
+
+ Reads the 32-bit PCI configuration register specified by Address, performs a
+ bitwise AND between the read result and the value specified by AndData,
+ performs a bitwise OR between the result of the AND operation and
+ the value specified by OrData, and writes the result to the 32-bit PCI
+ configuration register specified by Address. The value written to the PCI
+ configuration register is returned. This function must guarantee that all PCI
+ read and write operations are serialized.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 32-bit boundary, then ASSERT().
+
+ @param Address The address that encodes the PCI Bus, Device, Function and
+ Register.
+ @param AndData The value to AND with the PCI configuration register.
+ @param OrData The value to OR with the result of the AND operation.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT32
+EFIAPI
+PciExpressAndThenOr32 (
+ IN UINTN Address,
+ IN UINT32 AndData,
+ IN UINT32 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT32;
+ }
+ return MmioAndThenOr32 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ AndData,
+ OrData
+ );
+}
+
+/**
+ Reads a bit field of a PCI configuration register.
+
+ Reads the bit field in a 32-bit PCI configuration register. The bit field is
+ specified by the StartBit and the EndBit. The value of the bit field is
+ returned.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 32-bit boundary, then ASSERT().
+ If StartBit is greater than 31, then ASSERT().
+ If EndBit is greater than 31, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+
+ @param Address The PCI configuration register to read.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..31.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..31.
+
+ @return The value of the bit field read from the PCI configuration register.
+
+**/
+UINT32
+EFIAPI
+PciExpressBitFieldRead32 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT32;
+ }
+ return MmioBitFieldRead32 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit
+ );
+}
+
+/**
+ Writes a bit field to a PCI configuration register.
+
+ Writes Value to the bit field of the PCI configuration register. The bit
+ field is specified by the StartBit and the EndBit. All other bits in the
+ destination PCI configuration register are preserved. The new value of the
+ 32-bit register is returned.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 32-bit boundary, then ASSERT().
+ If StartBit is greater than 31, then ASSERT().
+ If EndBit is greater than 31, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If Value is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..31.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..31.
+ @param Value The new value of the bit field.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT32
+EFIAPI
+PciExpressBitFieldWrite32 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT32 Value
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT32;
+ }
+ return MmioBitFieldWrite32 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ Value
+ );
+}
+
+/**
+ Reads a bit field in a 32-bit PCI configuration, performs a bitwise OR, and
+ writes the result back to the bit field in the 32-bit port.
+
+ Reads the 32-bit PCI configuration register specified by Address, performs a
+ bitwise OR between the read result and the value specified by
+ OrData, and writes the result to the 32-bit PCI configuration register
+ specified by Address. The value written to the PCI configuration register is
+ returned. This function must guarantee that all PCI read and write operations
+ are serialized. Extra left bits in OrData are stripped.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 32-bit boundary, then ASSERT().
+ If StartBit is greater than 31, then ASSERT().
+ If EndBit is greater than 31, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..31.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..31.
+ @param OrData The value to OR with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT32
+EFIAPI
+PciExpressBitFieldOr32 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT32 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT32;
+ }
+ return MmioBitFieldOr32 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ OrData
+ );
+}
+
+/**
+ Reads a bit field in a 32-bit PCI configuration register, performs a bitwise
+ AND, and writes the result back to the bit field in the 32-bit register.
+
+ Reads the 32-bit PCI configuration register specified by Address, performs a
+ bitwise AND between the read result and the value specified by AndData, and
+ writes the result to the 32-bit PCI configuration register specified by
+ Address. The value written to the PCI configuration register is returned.
+ This function must guarantee that all PCI read and write operations are
+ serialized. Extra left bits in AndData are stripped.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 32-bit boundary, then ASSERT().
+ If StartBit is greater than 31, then ASSERT().
+ If EndBit is greater than 31, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..31.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..31.
+ @param AndData The value to AND with the PCI configuration register.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT32
+EFIAPI
+PciExpressBitFieldAnd32 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT32 AndData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT32;
+ }
+ return MmioBitFieldAnd32 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ AndData
+ );
+}
+
+/**
+ Reads a bit field in a 32-bit port, performs a bitwise AND followed by a
+ bitwise OR, and writes the result back to the bit field in the
+ 32-bit port.
+
+ Reads the 32-bit PCI configuration register specified by Address, performs a
+ bitwise AND followed by a bitwise OR between the read result and
+ the value specified by AndData, and writes the result to the 32-bit PCI
+ configuration register specified by Address. The value written to the PCI
+ configuration register is returned. This function must guarantee that all PCI
+ read and write operations are serialized. Extra left bits in both AndData and
+ OrData are stripped.
+
+ If Address > 0x0FFFFFFF, then ASSERT().
+ If Address is not aligned on a 32-bit boundary, then ASSERT().
+ If StartBit is greater than 31, then ASSERT().
+ If EndBit is greater than 31, then ASSERT().
+ If EndBit is less than StartBit, then ASSERT().
+ If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+ If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
+
+ @param Address The PCI configuration register to write.
+ @param StartBit The ordinal of the least significant bit in the bit field.
+ Range 0..31.
+ @param EndBit The ordinal of the most significant bit in the bit field.
+ Range 0..31.
+ @param AndData The value to AND with the PCI configuration register.
+ @param OrData The value to OR with the result of the AND operation.
+
+ @return The value written back to the PCI configuration register.
+
+**/
+UINT32
+EFIAPI
+PciExpressBitFieldAndThenOr32 (
+ IN UINTN Address,
+ IN UINTN StartBit,
+ IN UINTN EndBit,
+ IN UINT32 AndData,
+ IN UINT32 OrData
+ )
+{
+ ASSERT_INVALID_PCI_ADDRESS (Address);
+ if (IgnoreBusDeviceFunction (Address)) {
+ return MAX_UINT32;
+ }
+ return MmioBitFieldAndThenOr32 (
+ (UINTN)GetPciExpressBaseAddress () + Address,
+ StartBit,
+ EndBit,
+ AndData,
+ OrData
+ );
+}
+
+/**
+ Reads a range of PCI configuration registers into a caller supplied buffer.
+
+ Reads the range of PCI configuration registers specified by StartAddress and
+ Size into the buffer specified by Buffer. This function only allows the PCI
+ configuration registers from a single PCI function to be read. Size is
+ returned. When possible 32-bit PCI configuration read cycles are used to read
+ from StartAddress to StartAddress + Size. Due to alignment restrictions, 8-bit
+ and 16-bit PCI configuration read cycles may be used at the beginning and the
+ end of the range.
+
+ If StartAddress > 0x0FFFFFFF, then ASSERT().
+ If ((StartAddress & 0xFFF) + Size) > 0x1000, then ASSERT().
+ If Size > 0 and Buffer is NULL, then ASSERT().
+
+ @param StartAddress The starting address that encodes the PCI Bus, Device,
+ Function and Register.
+ @param Size The size in bytes of the transfer.
+ @param Buffer The pointer to a buffer receiving the data read.
+
+ @return Size read data from StartAddress.
+
+**/
+UINTN
+EFIAPI
+PciExpressReadBuffer (
+ IN UINTN StartAddress,
+ IN UINTN Size,
+ OUT VOID *Buffer
+ )
+{
+ UINTN ReturnValue;
+
+ ASSERT_INVALID_PCI_ADDRESS (StartAddress);
+ ASSERT (((StartAddress & 0xFFF) + Size) <= 0x1000);
+
+ if (Size == 0) {
+ return Size;
+ }
+
+ ASSERT (Buffer != NULL);
+
+ //
+ // Save Size for return
+ //
+ ReturnValue = Size;
+
+ if ((StartAddress & 1) != 0) {
+ //
+ // Read a byte if StartAddress is byte aligned
+ //
+ MmioWrite8 ((UINTN)Buffer, PciExpressRead8 (StartAddress));
+ StartAddress += sizeof (UINT8);
+ Size -= sizeof (UINT8);
+ Buffer = (UINT8 *)Buffer + 1;
+ }
+
+ if (Size >= sizeof (UINT16)&& (StartAddress & 2) != 0) {
+ //
+ // Read a word if StartAddress is word aligned
+ //
+ WriteUnaligned16 ((UINT16 *)Buffer, (UINT16)PciExpressRead16 (StartAddress));
+
+ StartAddress += sizeof (UINT16);
+ Size -= sizeof (UINT16);
+ Buffer = (UINT16 *)Buffer + 1;
+ }
+
+ while (Size >= sizeof (UINT32)) {
+ //
+ // Read as many double words as possible
+ //
+ WriteUnaligned32 ((UINT32 *)Buffer, (UINT32)PciExpressRead32 (StartAddress));
+
+ StartAddress += sizeof (UINT32);
+ Size -= sizeof (UINT32);
+ Buffer = (UINT32 *)Buffer + 1;
+ }
+
+ if (Size >= sizeof (UINT16)) {
+ //
+ // Read the last remaining word if exist
+ //
+ WriteUnaligned16 ((UINT16 *)Buffer, (UINT16)PciExpressRead16 (StartAddress));
+ StartAddress += sizeof (UINT16);
+ Size -= sizeof (UINT16);
+ Buffer = (UINT16 *)Buffer + 1;
+ }
+
+ if (Size >= sizeof (UINT8)) {
+ //
+ // Read the last remaining byte if exist
+ //
+ MmioWrite8 ((UINTN)Buffer, PciExpressRead8 (StartAddress));
+ }
+
+ return ReturnValue;
+}
+
+/**
+ Copies the data in a caller supplied buffer to a specified range of PCI
+ configuration space.
+
+ Writes the range of PCI configuration registers specified by StartAddress and
+ Size from the buffer specified by Buffer. This function only allows the PCI
+ configuration registers from a single PCI function to be written. Size is
+ returned. When possible 32-bit PCI configuration write cycles are used to
+ write from StartAddress to StartAddress + Size. Due to alignment restrictions,
+ 8-bit and 16-bit PCI configuration write cycles may be used at the beginning
+ and the end of the range.
+
+ If StartAddress > 0x0FFFFFFF, then ASSERT().
+ If ((StartAddress & 0xFFF) + Size) > 0x1000, then ASSERT().
+ If Size > 0 and Buffer is NULL, then ASSERT().
+
+ @param StartAddress The starting address that encodes the PCI Bus, Device,
+ Function and Register.
+ @param Size The size in bytes of the transfer.
+ @param Buffer The pointer to a buffer containing the data to write.
+
+ @return Size written to StartAddress.
+
+**/
+UINTN
+EFIAPI
+PciExpressWriteBuffer (
+ IN UINTN StartAddress,
+ IN UINTN Size,
+ IN VOID *Buffer
+ )
+{
+ UINTN ReturnValue;
+
+ ASSERT_INVALID_PCI_ADDRESS (StartAddress);
+ ASSERT (((StartAddress & 0xFFF) + Size) <= 0x1000);
+
+ if (Size == 0) {
+ return 0;
+ }
+
+ ASSERT (Buffer != NULL);
+
+ //
+ // Save Size for return
+ //
+ ReturnValue = Size;
+
+ if ((StartAddress & 1) != 0) {
+ //
+ // Write a byte if StartAddress is byte aligned
+ //
+ PciExpressWrite8 (StartAddress, *(UINT8 *)Buffer);
+ StartAddress += sizeof (UINT8);
+ Size -= sizeof (UINT8);
+ Buffer = (UINT8 *)Buffer + 1;
+ }
+
+ if (Size >= sizeof (UINT16) && (StartAddress & 2) != 0) {
+ //
+ // Write a word if StartAddress is word aligned
+ //
+ PciExpressWrite16 (StartAddress, ReadUnaligned16 ((UINT16 *)Buffer));
+ StartAddress += sizeof (UINT16);
+ Size -= sizeof (UINT16);
+ Buffer = (UINT16 *)Buffer + 1;
+ }
+
+ while (Size >= sizeof (UINT32)) {
+ //
+ // Write as many double words as possible
+ //
+ PciExpressWrite32 (StartAddress, ReadUnaligned32 ((UINT32 *)Buffer));
+ StartAddress += sizeof (UINT32);
+ Size -= sizeof (UINT32);
+ Buffer = (UINT32 *)Buffer + 1;
+ }
+
+ if (Size >= sizeof (UINT16)) {
+ //
+ // Write the last remaining word if exist
+ //
+ PciExpressWrite16 (StartAddress, ReadUnaligned16 ((UINT16 *)Buffer));
+ StartAddress += sizeof (UINT16);
+ Size -= sizeof (UINT16);
+ Buffer = (UINT16 *)Buffer + 1;
+ }
+
+ if (Size >= sizeof (UINT8)) {
+ //
+ // Write the last remaining byte if exist
+ //
+ PciExpressWrite8 (StartAddress, *(UINT8 *)Buffer);
+ }
+
+ return ReturnValue;
+}
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 07/14] Marvell/Armada7k8k: Implement PciHostBridgeLib
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (5 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 08/14] Marvell/Armada7k8k: Enable PCIE support Marcin Wojtas
` (7 subsequent siblings)
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
Add an implementation of the PciHostBridgeLib glue library that
describes the PCIe RC on this SoC so that the generic PCI host bridge
driver can attach to it.
This includes a constructor which performs the SoC specific init and
training sequences.
This patch is based on work of Ard Biesheuvel <ard.biesheuvel@linaro.org>
and Jing Hua <jinghua@marvell.com>/
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf | 52 +++
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h | 95 ++++++
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c | 265 +++++++++++++++
Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c | 345 ++++++++++++++++++++
4 files changed, 757 insertions(+)
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c
create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c
diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf
new file mode 100644
index 0000000..e46f71d
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf
@@ -0,0 +1,52 @@
+## @file
+# PCI Host Bridge Library instance for Marvell Armada 7k/8k SOC
+#
+# Copyright (c) 2017, Linaro Ltd. All rights reserved.<BR>
+# Copyright (c) 2019 Marvell International Ltd. All rights reserved.<BR>
+#
+# This program and the accompanying materials are licensed and made available
+# under the terms and conditions of the BSD License which accompanies this
+# distribution. The full text of the license may be found at
+# http://opensource.org/licenses/bsd-license.php
+# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR
+# IMPLIED.
+#
+#
+##
+
+[Defines]
+ INF_VERSION = 0x0001001B
+ BASE_NAME = Armada7k8kPciHostBridgeLib
+ FILE_GUID = 7f989c9d-02a0-4348-8aeb-ab2e1566fb18
+ MODULE_TYPE = DXE_DRIVER
+ VERSION_STRING = 1.0
+ LIBRARY_CLASS = PciHostBridgeLib|DXE_DRIVER
+ CONSTRUCTOR = Armada7k8kPciHostBridgeLibConstructor
+
+[Sources]
+ PciHostBridgeLib.c
+ PciHostBridgeLibConstructor.c
+
+[Packages]
+ ArmPkg/ArmPkg.dec
+ EmbeddedPkg/EmbeddedPkg.dec
+ MdeModulePkg/MdeModulePkg.dec
+ MdePkg/MdePkg.dec
+ Silicon/Marvell/Marvell.dec
+
+[LibraryClasses]
+ ArmLib
+ ArmadaSoCDescLib
+ DebugLib
+ DevicePathLib
+ MemoryAllocationLib
+ MvGpioLib
+ UefiBootServicesTableLib
+
+[Protocols]
+ gEmbeddedGpioProtocolGuid
+ gMarvellBoardDescProtocolGuid
+
+[Depex]
+ gMarvellPlatformInitCompleteProtocolGuid
diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h
new file mode 100644
index 0000000..8188001
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h
@@ -0,0 +1,95 @@
+/** @file
+ PCI Host Bridge Library instance for Marvell 70x0/80x0
+
+ Copyright (c) 2017, Linaro Ltd. All rights reserved.<BR>
+ Copyright (c) 2019 Marvell International Ltd. All rights reserved.<BR>
+
+ This program and the accompanying materials are licensed and made available
+ under the terms and conditions of the BSD License which accompanies this
+ distribution. The full text of the license may be found at
+ http://opensource.org/licenses/bsd-license.php.
+
+ THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, WITHOUT
+ WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+#ifndef __PCI_HOST_BRIDGE_LIB_CONSTRUCTOR_H__
+#define __PCI_HOST_BRIDGE_LIB_CONSTRUCTOR_H__
+
+#define IATU_VIEWPORT_OFF 0x900
+#define IATU_VIEWPORT_INBOUND BIT31
+#define IATU_VIEWPORT_OUTBOUND 0
+#define IATU_VIEWPORT_REGION_INDEX(Idx) ((Idx) & 7)
+
+#define IATU_REGION_CTRL_1_OFF_OUTBOUND_0 0x904
+#define IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_MEM 0x0
+#define IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_IO 0x2
+#define IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_CFG0 0x4
+#define IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_CFG1 0x5
+
+#define IATU_REGION_CTRL_2_OFF_OUTBOUND_0 0x908
+#define IATU_REGION_CTRL_2_OFF_OUTBOUND_0_REGION_EN BIT31
+#define IATU_REGION_CTRL_2_OFF_OUTBOUND_0_CFG_SHIFT_MODE BIT28
+
+#define IATU_LWR_BASE_ADDR_OFF_OUTBOUND_0 0x90C
+#define IATU_UPPER_BASE_ADDR_OFF_OUTBOUND_0 0x910
+#define IATU_LIMIT_ADDR_OFF_OUTBOUND_0 0x914
+#define IATU_LWR_TARGET_ADDR_OFF_OUTBOUND_0 0x918
+#define IATU_UPPER_TARGET_ADDR_OFF_OUTBOUND_0 0x91C
+
+#define PORT_LINK_CTRL_OFF 0x710
+#define PORT_LINK_CTRL_OFF_LINK_CAPABLE_x1 (0x01 << 16)
+#define PORT_LINK_CTRL_OFF_LINK_CAPABLE_x2 (0x03 << 16)
+#define PORT_LINK_CTRL_OFF_LINK_CAPABLE_x4 (0x07 << 16)
+#define PORT_LINK_CTRL_OFF_LINK_CAPABLE_x8 (0x0f << 16)
+#define PORT_LINK_CTRL_OFF_LINK_CAPABLE_x16 (0x1f << 16)
+#define PORT_LINK_CTRL_OFF_LINK_CAPABLE_MASK (0x3f << 16)
+
+#define GEN2_CTRL_OFF 0x80c
+#define GEN2_CTRL_OFF_NUM_OF_LANES(n) (((n) & 0x1f) << 8)
+#define GEN2_CTRL_OFF_NUM_OF_LANES_MASK (0x1f << 8)
+#define GEN2_CTRL_OFF_DIRECT_SPEED_CHANGE BIT17
+
+#define PCIE_GLOBAL_CTRL_OFFSET 0x8000
+#define PCIE_GLOBAL_APP_LTSSM_EN BIT2
+#define PCIE_GLOBAL_CTRL_DEVICE_TYPE_RC (0x4 << 4)
+#define PCIE_GLOBAL_CTRL_DEVICE_TYPE_MASK (0xF << 4)
+
+#define PCIE_GLOBAL_STATUS_REG 0x8008
+#define PCIE_GLOBAL_STATUS_RDLH_LINK_UP BIT1
+#define PCIE_GLOBAL_STATUS_PHY_LINK_UP BIT9
+
+#define PCIE_PM_STATUS 0x8014
+#define PCIE_PM_LTSSM_STAT_MASK (0x3f << 3)
+
+#define PCIE_GLOBAL_INT_MASK1_REG 0x8020
+#define PCIE_INT_A_ASSERT_MASK BIT9
+#define PCIE_INT_B_ASSERT_MASK BIT10
+#define PCIE_INT_C_ASSERT_MASK BIT11
+#define PCIE_INT_D_ASSERT_MASK BIT12
+
+#define PCIE_ARCACHE_TRC_REG 0x8050
+#define PCIE_AWCACHE_TRC_REG 0x8054
+#define PCIE_ARUSER_REG 0x805C
+#define PCIE_AWUSER_REG 0x8060
+
+#define ARCACHE_DEFAULT_VALUE 0x3511
+#define AWCACHE_DEFAULT_VALUE 0x5311
+
+#define AX_USER_DOMAIN_INNER_SHAREABLE (0x1 << 4)
+#define AX_USER_DOMAIN_OUTER_SHAREABLE (0x2 << 4)
+#define AX_USER_DOMAIN_MASK (0x3 << 4)
+
+#define PCIE_LINK_CAPABILITY 0x7C
+#define PCIE_LINK_CTL_2 0xA0
+#define TARGET_LINK_SPEED_MASK 0xF
+#define LINK_SPEED_GEN_1 0x1
+#define LINK_SPEED_GEN_2 0x2
+#define LINK_SPEED_GEN_3 0x3
+
+#define PCIE_GEN3_EQU_CTRL 0x8A8
+#define GEN3_EQU_EVAL_2MS_DISABLE BIT5
+
+#define PCIE_LINK_UP_TIMEOUT_US 40000
+
+#endif
diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c
new file mode 100644
index 0000000..58cdf83
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c
@@ -0,0 +1,265 @@
+/** @file
+ PCI Host Bridge Library instance for Marvell Armada 70x0/80x0
+
+ Copyright (c) 2017, Linaro Ltd. All rights reserved.<BR>
+ Copyright (c) 2019 Marvell International Ltd. All rights reserved.<BR>
+
+ This program and the accompanying materials are licensed and made available
+ under the terms and conditions of the BSD License which accompanies this
+ distribution. The full text of the license may be found at
+ http://opensource.org/licenses/bsd-license.php.
+
+ THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, WITHOUT
+ WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+#include <PiDxe.h>
+
+#include <Library/DebugLib.h>
+#include <Library/DevicePathLib.h>
+#include <Library/MemoryAllocationLib.h>
+#include <Library/PcdLib.h>
+#include <Library/PciHostBridgeLib.h>
+#include <Library/UefiBootServicesTableLib.h>
+
+#include <Protocol/BoardDesc.h>
+#include <Protocol/PciHostBridgeResourceAllocation.h>
+#include <Protocol/PciRootBridgeIo.h>
+
+#pragma pack(1)
+typedef struct {
+ ACPI_HID_DEVICE_PATH AcpiDevicePath;
+ EFI_DEVICE_PATH_PROTOCOL EndDevicePath;
+} EFI_PCI_ROOT_BRIDGE_DEVICE_PATH;
+#pragma pack ()
+
+STATIC EFI_PCI_ROOT_BRIDGE_DEVICE_PATH mEfiPciRootBridgeDevicePath = {
+ {
+ {
+ ACPI_DEVICE_PATH,
+ ACPI_DP,
+ {
+ (UINT8)(sizeof (ACPI_HID_DEVICE_PATH)),
+ (UINT8)((sizeof (ACPI_HID_DEVICE_PATH)) >> 8)
+ }
+ },
+ EISA_PNP_ID (0x0A08), // PCI Express
+ 0
+ },
+
+ {
+ END_DEVICE_PATH_TYPE,
+ END_ENTIRE_DEVICE_PATH_SUBTYPE,
+ {
+ END_DEVICE_PATH_LENGTH,
+ 0
+ }
+ }
+};
+
+GLOBAL_REMOVE_IF_UNREFERENCED
+CHAR16 *mPciHostBridgeLibAcpiAddressSpaceTypeStr[] = {
+ L"Mem", L"I/O", L"Bus"
+};
+
+/**
+ Return all the root bridge instances in an array.
+
+ @param Count Return the count of root bridge instances.
+
+ @return All the root bridge instances in an array.
+ The array should be passed into PciHostBridgeFreeRootBridges()
+ when it's not used.
+
+**/
+PCI_ROOT_BRIDGE *
+EFIAPI
+PciHostBridgeGetRootBridges (
+ UINTN *Count
+ )
+{
+ MV_BOARD_PCIE_DESCRIPTION CONST *BoardPcieDescription;
+ MARVELL_BOARD_DESC_PROTOCOL *BoardDescriptionProtocol;
+ MV_PCIE_CONTROLLER CONST *PcieController;
+ PCI_ROOT_BRIDGE *PciRootBridges;
+ PCI_ROOT_BRIDGE *RootBridge;
+ EFI_STATUS Status;
+ UINTN Index;
+
+ *Count = 0;
+
+ /* Obtain list of available controllers */
+ Status = gBS->LocateProtocol (&gMarvellBoardDescProtocolGuid,
+ NULL,
+ (VOID **)&BoardDescriptionProtocol);
+ if (EFI_ERROR (Status)) {
+ DEBUG ((DEBUG_ERROR,
+ "%a: Cannot locate BoardDesc protocol\n",
+ __FUNCTION__));
+ return NULL;
+ }
+
+ Status = BoardDescriptionProtocol->PcieDescriptionGet (
+ BoardDescriptionProtocol,
+ &BoardPcieDescription);
+ if (Status == EFI_NOT_FOUND) {
+ /* No controllers used on the platform, exit silently */
+ return NULL;
+ } else if (EFI_ERROR (Status)) {
+ DEBUG ((DEBUG_ERROR,
+ "%a: Cannot get Pcie board desc from BoardDesc protocol\n",
+ __FUNCTION__));
+ return NULL;
+ }
+
+ /* Assign return values */
+ PciRootBridges = AllocateZeroPool (BoardPcieDescription->PcieControllerCount *
+ sizeof (PCI_ROOT_BRIDGE));
+ if (PciRootBridges == NULL) {
+ DEBUG ((DEBUG_ERROR, "%a: Fail to allocate resources\n", __FUNCTION__));
+ return NULL;
+ }
+
+ *Count = BoardPcieDescription->PcieControllerCount;
+ RootBridge = PciRootBridges;
+
+ /* Fill information of all root bridge instances */
+ for (Index = 0; Index < *Count; Index++, RootBridge++) {
+
+ PcieController = &(BoardPcieDescription->PcieControllers[Index]);
+
+ RootBridge->Segment = 0;
+ RootBridge->Supports = 0;
+ RootBridge->Attributes = RootBridge->Supports;
+
+ RootBridge->DmaAbove4G = FALSE;
+
+#ifndef MDE_CPU_ARM
+ RootBridge->AllocationAttributes = EFI_PCI_HOST_BRIDGE_COMBINE_MEM_PMEM |
+ EFI_PCI_HOST_BRIDGE_MEM64_DECODE;
+#else
+ RootBridge->AllocationAttributes = EFI_PCI_HOST_BRIDGE_COMBINE_MEM_PMEM;
+#endif
+
+ RootBridge->Bus.Base = PcieController->PcieBusMin;
+ RootBridge->Bus.Limit = PcieController->PcieBusMax;
+ RootBridge->Io.Base = PcieController->PcieIoWinBase;
+ RootBridge->Io.Limit = PcieController->PcieIoWinBase +
+ PcieController->PcieIoWinSize - 1;
+ RootBridge->Io.Translation = MAX_UINT64 -
+ PcieController->PcieIoTranslation + 1;
+ RootBridge->Mem.Base = PcieController->PcieMmio32WinBase;
+ RootBridge->Mem.Limit = PcieController->PcieMmio32WinBase +
+ PcieController->PcieMmio32WinSize - 1;
+ RootBridge->Mem.Translation = MAX_UINT64 -
+ PcieController->PcieMmio32Translation + 1;
+#ifndef MDE_CPU_ARM
+ RootBridge->MemAbove4G.Base = PcieController->PcieMmio64WinBase;
+ RootBridge->MemAbove4G.Limit = PcieController->PcieMmio64WinBase +
+ PcieController->PcieMmio64WinSize - 1;
+ RootBridge->MemAbove4G.Translation = MAX_UINT64 -
+ PcieController->PcieMmio64Translation + 1;
+#else
+ RootBridge->MemAbove4G.Base = MAX_UINT64;
+ RootBridge->MemAbove4G.Limit = 0;
+ RootBridge->MemAbove4G.Translation = 0;
+#endif
+
+ /* No separate ranges for prefetchable and non-prefetchable BARs */
+ RootBridge->PMem.Base = MAX_UINT64;
+ RootBridge->PMem.Limit = 0;
+ RootBridge->PMemAbove4G.Base = MAX_UINT64;
+ RootBridge->PMemAbove4G.Limit = 0;
+
+
+ RootBridge->NoExtendedConfigSpace = FALSE;
+
+ RootBridge->DevicePath = (EFI_DEVICE_PATH_PROTOCOL *)&mEfiPciRootBridgeDevicePath;
+ }
+
+ return PciRootBridges;
+}
+
+/**
+ Free the root bridge instances array returned from PciHostBridgeGetRootBridges().
+
+ @param Bridges The root bridge instances array.
+ @param Count The count of the array.
+
+**/
+VOID
+EFIAPI
+PciHostBridgeFreeRootBridges (
+ PCI_ROOT_BRIDGE *Bridges,
+ UINTN Count
+ )
+{
+ FreePool (Bridges);
+}
+
+/**
+ Inform the platform that the resource conflict happens.
+
+ @param HostBridgeHandle Handle of the Host Bridge.
+ @param Configuration Pointer to PCI I/O and PCI memory resource
+ descriptors. The Configuration contains the resources
+ for all the root bridges. The resource for each root
+ bridge is terminated with END descriptor and an
+ additional END is appended indicating the end of the
+ entire resources. The resource descriptor field
+ values follow the description in
+ EFI_PCI_HOST_BRIDGE_RESOURCE_ALLOCATION_PROTOCOL
+ .SubmitResources().
+
+**/
+VOID
+EFIAPI
+PciHostBridgeResourceConflict (
+ EFI_HANDLE HostBridgeHandle,
+ VOID *Configuration
+ )
+{
+ EFI_ACPI_ADDRESS_SPACE_DESCRIPTOR *Descriptor;
+ CHAR16 *MemoryTypeDescription[] = { L"(Prefetchable)", L"" };
+ CHAR16 *MemoryType;
+ UINTN RootBridgeIndex;
+
+ DEBUG ((DEBUG_ERROR, "PciHostBridge: Resource conflict happens!\n"));
+
+ RootBridgeIndex = 0;
+ Descriptor = (EFI_ACPI_ADDRESS_SPACE_DESCRIPTOR *)Configuration;
+
+ while (Descriptor->Desc == ACPI_ADDRESS_SPACE_DESCRIPTOR) {
+
+ DEBUG ((DEBUG_ERROR, "RootBridge[%d]:\n", RootBridgeIndex++));
+
+ for (; Descriptor->Desc == ACPI_ADDRESS_SPACE_DESCRIPTOR; Descriptor++) {
+ ASSERT (Descriptor->ResType <
+ ARRAY_SIZE (mPciHostBridgeLibAcpiAddressSpaceTypeStr));
+
+ DEBUG ((DEBUG_ERROR,
+ " %s: Length/Alignment = 0x%lx / 0x%lx\n",
+ mPciHostBridgeLibAcpiAddressSpaceTypeStr[Descriptor->ResType],
+ Descriptor->AddrLen, Descriptor->AddrRangeMax));
+
+ if (Descriptor->ResType == ACPI_ADDRESS_SPACE_TYPE_MEM) {
+ if (Descriptor->SpecificFlag &
+ EFI_ACPI_MEMORY_RESOURCE_SPECIFIC_FLAG_CACHEABLE_PREFETCHABLE) {
+ MemoryType = MemoryTypeDescription[0];
+ } else {
+ MemoryType = MemoryTypeDescription[1];
+ }
+
+ DEBUG ((DEBUG_ERROR,
+ " Granularity/SpecificFlag = %ld / %02x%s\n",
+ Descriptor->AddrSpaceGranularity,
+ Descriptor->SpecificFlag,
+ MemoryType));
+ }
+ }
+ /* Skip the END descriptor for root bridge */
+ ASSERT (Descriptor->Desc == ACPI_END_TAG_DESCRIPTOR);
+ Descriptor = (EFI_ACPI_ADDRESS_SPACE_DESCRIPTOR *)(
+ (EFI_ACPI_END_TAG_DESCRIPTOR *)Descriptor + 1);
+ }
+}
diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c
new file mode 100644
index 0000000..8376756
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c
@@ -0,0 +1,345 @@
+/** @file
+ PCI Host Bridge Library instance for Marvell 70x0/80x0
+
+ Copyright (c) 2017, Linaro Ltd. All rights reserved.<BR>
+ Copyright (c) 2019 Marvell International Ltd. All rights reserved.<BR>
+
+ This program and the accompanying materials are licensed and made available
+ under the terms and conditions of the BSD License which accompanies this
+ distribution. The full text of the license may be found at
+ http://opensource.org/licenses/bsd-license.php.
+
+ THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, WITHOUT
+ WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+
+#include <PiDxe.h>
+
+#include <IndustryStandard/Pci22.h>
+
+#include <Library/ArmLib.h>
+#include <Library/BaseLib.h>
+#include <Library/DebugLib.h>
+#include <Library/IoLib.h>
+#include <Library/MvGpioLib.h>
+#include <Library/UefiBootServicesTableLib.h>
+
+#include <Protocol/BoardDesc.h>
+
+#include "PciHostBridgeLibConstructor.h"
+
+/**
+ This function configures PCIE controllers IATU windows.
+
+ @param [in] PcieDbiAddress PCIE controller base address.
+ @param [in] Index IATU window index.
+ @param [in] CpuBase Address from the CPU perspective.
+ @param [in] PciBase Target PCIE address.
+ @param [in] Size IATU window size.
+ @param [in] Type IATU window type.
+ @param [in] EnableFlags Extra configuration flags.
+
+ @retval none
+
+**/
+STATIC
+VOID
+ConfigureWindow (
+ IN EFI_PHYSICAL_ADDRESS PcieDbiAddress,
+ IN UINTN Index,
+ IN UINT64 CpuBase,
+ IN UINT64 PciBase,
+ IN UINT64 Size,
+ IN UINTN Type,
+ IN UINTN EnableFlags
+ )
+{
+ ArmDataMemoryBarrier ();
+
+ MmioWrite32 (PcieDbiAddress + IATU_VIEWPORT_OFF,
+ IATU_VIEWPORT_OUTBOUND | IATU_VIEWPORT_REGION_INDEX (Index));
+
+ ArmDataMemoryBarrier ();
+
+ MmioWrite32 (PcieDbiAddress + IATU_LWR_BASE_ADDR_OFF_OUTBOUND_0,
+ (UINT32)(CpuBase & MAX_UINT32));
+ MmioWrite32 (PcieDbiAddress + IATU_UPPER_BASE_ADDR_OFF_OUTBOUND_0,
+ (UINT32)(CpuBase >> 32));
+ MmioWrite32 (PcieDbiAddress + IATU_LIMIT_ADDR_OFF_OUTBOUND_0,
+ (UINT32)(CpuBase + Size - 1));
+ MmioWrite32 (PcieDbiAddress + IATU_LWR_TARGET_ADDR_OFF_OUTBOUND_0,
+ (UINT32)(PciBase & MAX_UINT32));
+ MmioWrite32 (PcieDbiAddress + IATU_UPPER_TARGET_ADDR_OFF_OUTBOUND_0,
+ (UINT32)(PciBase >> 32));
+ MmioWrite32 (PcieDbiAddress + IATU_REGION_CTRL_1_OFF_OUTBOUND_0,
+ Type);
+ MmioWrite32 (PcieDbiAddress + IATU_REGION_CTRL_2_OFF_OUTBOUND_0,
+ IATU_REGION_CTRL_2_OFF_OUTBOUND_0_REGION_EN | EnableFlags);
+}
+
+/**
+ Perform PCIE slot reset using external GPIO pin.
+
+ @param [in] PcieDbiAddress PCIE controller base address.
+
+ @retval none
+
+**/
+STATIC
+VOID
+WaitForLink (
+ IN EFI_PHYSICAL_ADDRESS PcieDbiAddress
+ )
+{
+ UINT32 Mask;
+ UINT32 Status;
+ UINT32 Timeout;
+
+ if (!(MmioRead32 (PcieDbiAddress + PCIE_PM_STATUS) & PCIE_PM_LTSSM_STAT_MASK)) {
+ DEBUG ((DEBUG_INIT, "%a: no PCIE device detected\n", __FUNCTION__));
+ return;
+ }
+
+ /* Wait for the link to establish itself. */
+ DEBUG ((DEBUG_INIT, "%a: waiting for PCIE link\n", __FUNCTION__));
+
+ Mask = PCIE_GLOBAL_STATUS_RDLH_LINK_UP | PCIE_GLOBAL_STATUS_PHY_LINK_UP;
+ Timeout = PCIE_LINK_UP_TIMEOUT_US / 10;
+ do {
+ Status = MmioRead32 (PcieDbiAddress + PCIE_GLOBAL_STATUS_REG);
+ if ((Status & Mask) == Mask) {
+ DEBUG ((DEBUG_ERROR, "pcie@0x%x link UP\n", PcieDbiAddress));
+ break;
+ }
+ /* Wait 10us between each link status check. */
+ gBS->Stall (10);
+ } while (Timeout--);
+}
+
+/**
+ Perform PCIE slot reset using external GPIO pin.
+
+ @param [in] *PcieResetGpio GPIO pin description.
+
+ @retval EFI_SUCEESS PCIE slot reset succeeded.
+ @retval Other Return error status.
+
+**/
+STATIC
+EFI_STATUS
+ResetPcieSlot (
+ IN MV_GPIO_PIN CONST *PcieResetGpio
+ )
+{
+ EMBEDDED_GPIO_MODE Mode;
+ EMBEDDED_GPIO_PIN GpioPin;
+ EMBEDDED_GPIO *GpioProtocol;
+ EFI_STATUS Status;
+
+ /* Get GPIO protocol. */
+ Status = MvGpioGetProtocol (PcieResetGpio->ControllerType, &GpioProtocol);
+ if (EFI_ERROR (Status)) {
+ DEBUG ((DEBUG_ERROR, "%a: Unable to find GPIO protocol\n", __FUNCTION__));
+ return Status;
+ }
+
+ GpioPin = GPIO (PcieResetGpio->ControllerId, PcieResetGpio->PinNumber),
+
+ /* Activate reset. */
+ Mode = PcieResetGpio->ActiveHigh ? GPIO_MODE_OUTPUT_1 : GPIO_MODE_OUTPUT_0;
+ Status = GpioProtocol->Set (GpioProtocol, GpioPin, Mode);
+
+ /*
+ * According to the PCIE specification, the reset signal must be active
+ * for minimum 100ms. To be on a safe side, use 150ms delay.
+ */
+ MemoryFence ();
+ gBS->Stall (150 * 1000);
+
+ /* Dectivate reset. */
+ Mode = PcieResetGpio->ActiveHigh ? GPIO_MODE_OUTPUT_0 : GPIO_MODE_OUTPUT_1;
+ Status = GpioProtocol->Set (GpioProtocol, GpioPin, Mode);
+
+ /*
+ * The controller cannot be configured (e.g. the clocks have to establish)
+ * during 20ms period after the reset is deactivated.
+ */
+ MemoryFence ();
+ gBS->Stall (20 * 1000);
+
+ return EFI_SUCCESS;
+}
+
+/**
+ Obtain resources and perform a low-level PCIE controllers
+ configuration.
+
+ @param [in] ImageHandle The image handle.
+ @param [in] *SystemTable The system table.
+
+ @retval EFI_SUCEESS PCIE configuration successful.
+ @retval Other Return error status.
+
+**/
+EFI_STATUS
+EFIAPI
+Armada7k8kPciHostBridgeLibConstructor (
+ IN EFI_HANDLE ImageHandle,
+ IN EFI_SYSTEM_TABLE *SystemTable
+ )
+{
+ MV_BOARD_PCIE_DESCRIPTION CONST *BoardPcieDescription;
+ MARVELL_BOARD_DESC_PROTOCOL *BoardDescriptionProtocol;
+ MV_PCIE_CONTROLLER CONST *PcieController;
+ EFI_PHYSICAL_ADDRESS PcieDbiAddress;
+ EFI_STATUS Status;
+ UINTN Index;
+
+ /* Obtain list of available controllers */
+ Status = gBS->LocateProtocol (&gMarvellBoardDescProtocolGuid,
+ NULL,
+ (VOID **)&BoardDescriptionProtocol);
+ if (EFI_ERROR (Status)) {
+ DEBUG ((DEBUG_ERROR,
+ "%a: Cannot locate BoardDesc protocol\n",
+ __FUNCTION__));
+ return EFI_DEVICE_ERROR;
+ }
+
+ Status = BoardDescriptionProtocol->PcieDescriptionGet (
+ BoardDescriptionProtocol,
+ &BoardPcieDescription);
+ if (Status == EFI_NOT_FOUND) {
+ /* No controllers used on the platform, exit silently */
+ return EFI_SUCCESS;
+ } else if (EFI_ERROR (Status)) {
+ DEBUG ((DEBUG_ERROR,
+ "%a: Cannot get Pcie board desc from BoardDesc protocol\n",
+ __FUNCTION__));
+ return EFI_DEVICE_ERROR;
+ }
+
+ for (Index = 0; Index < BoardPcieDescription->PcieControllerCount; Index++) {
+
+ PcieController = &(BoardPcieDescription->PcieControllers[Index]);
+
+ ASSERT (PcieController->PcieBusMin == 0);
+ ASSERT (PcieController->ConfigSpaceAddress % SIZE_256MB == 0);
+
+ if (PcieController->HaveResetGpio == TRUE) {
+ /* Reset PCIE slot */
+ Status = ResetPcieSlot (&PcieController->PcieResetGpio);
+ if (EFI_ERROR (Status)) {
+ DEBUG ((DEBUG_ERROR,
+ "%a: Cannot reset Pcie Slot\n",
+ __FUNCTION__));
+ return EFI_DEVICE_ERROR;
+ }
+ }
+
+ /* Low level PCIE controller configuration */
+ PcieDbiAddress = PcieController->PcieDbiAddress;
+
+ MmioAndThenOr32 (PcieDbiAddress + PORT_LINK_CTRL_OFF,
+ ~PORT_LINK_CTRL_OFF_LINK_CAPABLE_MASK,
+ PORT_LINK_CTRL_OFF_LINK_CAPABLE_x4);
+
+ MmioAndThenOr32 (PcieDbiAddress + GEN2_CTRL_OFF,
+ ~GEN2_CTRL_OFF_NUM_OF_LANES_MASK,
+ GEN2_CTRL_OFF_NUM_OF_LANES(4) | GEN2_CTRL_OFF_DIRECT_SPEED_CHANGE);
+
+ MmioAndThenOr32 (PcieDbiAddress + PCIE_GLOBAL_CTRL_OFFSET,
+ ~(PCIE_GLOBAL_CTRL_DEVICE_TYPE_MASK | PCIE_GLOBAL_APP_LTSSM_EN),
+ PCIE_GLOBAL_CTRL_DEVICE_TYPE_RC);
+
+ MmioWrite32 (PcieDbiAddress + PCIE_ARCACHE_TRC_REG,
+ ARCACHE_DEFAULT_VALUE);
+
+ MmioWrite32 (PcieDbiAddress + PCIE_AWCACHE_TRC_REG,
+ AWCACHE_DEFAULT_VALUE);
+
+ MmioAndThenOr32 (PcieDbiAddress + PCIE_ARUSER_REG,
+ ~AX_USER_DOMAIN_MASK,
+ AX_USER_DOMAIN_OUTER_SHAREABLE);
+
+ MmioAndThenOr32 (PcieDbiAddress + PCIE_AWUSER_REG,
+ ~AX_USER_DOMAIN_MASK,
+ AX_USER_DOMAIN_OUTER_SHAREABLE);
+
+ MmioAndThenOr32 (PcieDbiAddress + PCIE_LINK_CTL_2,
+ ~TARGET_LINK_SPEED_MASK,
+ LINK_SPEED_GEN_3);
+
+ MmioAndThenOr32 (PcieDbiAddress + PCIE_LINK_CAPABILITY,
+ ~TARGET_LINK_SPEED_MASK,
+ LINK_SPEED_GEN_3);
+
+ MmioOr32 (PcieDbiAddress + PCIE_GEN3_EQU_CTRL,
+ GEN3_EQU_EVAL_2MS_DISABLE);
+
+ MmioOr32 (PcieDbiAddress + PCIE_GLOBAL_CTRL_OFFSET,
+ PCIE_GLOBAL_APP_LTSSM_EN);
+
+ /* Region 0: MMIO32 range */
+ ConfigureWindow (PcieDbiAddress,
+ PcieController->PcieMmio32WinBase - PcieController->PcieMmio32Translation,
+ PcieController->PcieMmio32WinBase,
+ PcieController->PcieMmio32WinBase,
+ PcieController->PcieMmio32WinSize,
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_MEM,
+ 0);
+
+ /* Region 1: Type 0 config space */
+ ConfigureWindow (PcieDbiAddress,
+ 1,
+ PcieController->ConfigSpaceAddress,
+ 0x0,
+ SIZE_64KB,
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_CFG0,
+ IATU_REGION_CTRL_2_OFF_OUTBOUND_0_CFG_SHIFT_MODE);
+
+ /* Region 2: Type 1 config space */
+ ConfigureWindow (PcieDbiAddress,
+ 2,
+ PcieController->ConfigSpaceAddress + SIZE_64KB,
+ 0x0,
+ PcieController->PcieBusMax * SIZE_1MB,
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_CFG1,
+ IATU_REGION_CTRL_2_OFF_OUTBOUND_0_CFG_SHIFT_MODE);
+
+ /* Region 3: port I/O range */
+ ConfigureWindow (PcieDbiAddress,
+ 3,
+ PcieController->PcieIoTranslation,
+ PcieController->PcieIoWinBase,
+ PcieController->PcieIoWinSize,
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_IO,
+ 0);
+
+ /* Region 4: MMIO64 range */
+ ConfigureWindow (PcieDbiAddress,
+ 4,
+ PcieController->PcieMmio64WinBase,
+ PcieController->PcieMmio64WinBase,
+ PcieController->PcieMmio64WinSize,
+ IATU_REGION_CTRL_1_OFF_OUTBOUND_0_TYPE_MEM,
+ 0);
+
+ MmioOr32 (PcieDbiAddress + PCIE_GLOBAL_INT_MASK1_REG,
+ PCIE_INT_A_ASSERT_MASK |
+ PCIE_INT_B_ASSERT_MASK |
+ PCIE_INT_C_ASSERT_MASK |
+ PCIE_INT_D_ASSERT_MASK);
+
+ WaitForLink (PcieDbiAddress);
+
+ /* Enable the RC */
+ MmioOr32 (PcieDbiAddress + PCI_COMMAND_OFFSET,
+ EFI_PCI_COMMAND_IO_SPACE |
+ EFI_PCI_COMMAND_MEMORY_SPACE |
+ EFI_PCI_COMMAND_BUS_MASTER);
+ }
+
+ return EFI_SUCCESS;
+}
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 08/14] Marvell/Armada7k8k: Enable PCIE support
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (6 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 07/14] Marvell/Armada7k8k: Implement PciHostBridgeLib Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 09/14] Marvell/Armada80x0McBin: Enable ACPI " Marcin Wojtas
` (6 subsequent siblings)
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
Wire up the platform libraries to the generic drivers so that we can use
PCI devices and UEFI, and leave the controller initialized so that the
OS can boot it using a generic driver of its own.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc | 18 ++++++++++++++++--
Silicon/Marvell/Armada7k8k/Armada7k8k.fdf | 5 +++++
2 files changed, 21 insertions(+), 2 deletions(-)
diff --git a/Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc b/Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc
index 0cf5d84..757c6b2 100644
--- a/Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc
+++ b/Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc
@@ -70,8 +70,10 @@
IoLib|MdePkg/Library/BaseIoLibIntrinsic/BaseIoLibIntrinsic.inf
UefiDecompressLib|MdePkg/Library/BaseUefiDecompressLib/BaseUefiDecompressLib.inf
CpuLib|MdePkg/Library/BaseCpuLib/BaseCpuLib.inf
- PciLib|MdePkg/Library/BasePciLibCf8/BasePciLibCf8.inf
- PciCf8Lib|MdePkg/Library/BasePciCf8Lib/BasePciCf8Lib.inf
+ PciLib|MdePkg/Library/BasePciLibPciExpress/BasePciLibPciExpress.inf
+ PciHostBridgeLib|Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf
+ PciSegmentLib|MdePkg/Library/BasePciSegmentLibPci/BasePciSegmentLibPci.inf
+ PciExpressLib|Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
# Basic UEFI services libraries
UefiLib|MdePkg/Library/UefiLib/UefiLib.inf
@@ -406,6 +408,13 @@
gEfiMdeModulePkgTokenSpaceGuid.PcdFlashNvStorageFtwWorkingSize|0x00010000
gEfiMdeModulePkgTokenSpaceGuid.PcdFlashNvStorageFtwSpareSize|0x00010000
+ # PCIE
+ gArmTokenSpaceGuid.PcdPciIoTranslation|0xEFF00000
+ gEfiMdePkgTokenSpaceGuid.PcdPciExpressBaseAddress|0xE0000000
+
+ # SoC Configuration Space
+ gMarvellTokenSpaceGuid.PcdConfigSpaceBaseAddress|0xE0000000
+
!if $(CAPSULE_ENABLE)
[PcdsDynamicExDefault.common.DEFAULT]
gEfiSignedCapsulePkgTokenSpaceGuid.PcdEdkiiSystemFirmwareImageDescriptor|{0x0}|VOID*|0x100
@@ -519,6 +528,11 @@
MdeModulePkg/Bus/Pci/SdMmcPciHcDxe/SdMmcPciHcDxe.inf
Silicon/Marvell/Drivers/SdMmc/XenonDxe/XenonDxe.inf
+ # PCI
+ ArmPkg/Drivers/ArmPciCpuIo2Dxe/ArmPciCpuIo2Dxe.inf
+ MdeModulePkg/Bus/Pci/PciHostBridgeDxe/PciHostBridgeDxe.inf
+ MdeModulePkg/Bus/Pci/PciBusDxe/PciBusDxe.inf
+
# Console packages
MdeModulePkg/Universal/Console/ConPlatformDxe/ConPlatformDxe.inf
MdeModulePkg/Universal/Console/ConSplitterDxe/ConSplitterDxe.inf
diff --git a/Silicon/Marvell/Armada7k8k/Armada7k8k.fdf b/Silicon/Marvell/Armada7k8k/Armada7k8k.fdf
index d2bbded..d24be73 100644
--- a/Silicon/Marvell/Armada7k8k/Armada7k8k.fdf
+++ b/Silicon/Marvell/Armada7k8k/Armada7k8k.fdf
@@ -168,6 +168,11 @@ FvNameGuid = 5eda4200-2c5f-43cb-9da3-0baf74b1b30c
INF MdeModulePkg/Bus/Pci/SdMmcPciHcDxe/SdMmcPciHcDxe.inf
INF Silicon/Marvell/Drivers/SdMmc/XenonDxe/XenonDxe.inf
+ # PCI
+ INF ArmPkg/Drivers/ArmPciCpuIo2Dxe/ArmPciCpuIo2Dxe.inf
+ INF MdeModulePkg/Bus/Pci/PciHostBridgeDxe/PciHostBridgeDxe.inf
+ INF MdeModulePkg/Bus/Pci/PciBusDxe/PciBusDxe.inf
+
# Multiple Console IO support
INF MdeModulePkg/Universal/Console/ConPlatformDxe/ConPlatformDxe.inf
INF MdeModulePkg/Universal/Console/ConSplitterDxe/ConSplitterDxe.inf
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 09/14] Marvell/Armada80x0McBin: Enable ACPI PCIE support
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (7 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 08/14] Marvell/Armada7k8k: Enable PCIE support Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 10/14] Marvell/Armada80x0Db: " Marcin Wojtas
` (5 subsequent siblings)
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
This patch adds description of the PCIE controller in
ACPI tables of MacchiatoBin community board.
Due to the quirky nature of the Synopsys Designware PCIe IP,
the type 0 configuration is broadcast and whatever device
is plugged into slot, will appear at each 32 device
positions of bus0.
In order to prevent above, shift the config space base address
to the second half of the smallest ATU window (64kB), and limit
bus number to 1. Thanks to this, the pci-host-generic driver
could be used in OS with ACPI, however with the limitation
to support only single device in the slot.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin.inf | 1 +
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h | 26 +++++
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Dsdt.asl | 108 ++++++++++++++++++++
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc | 47 +++++++++
4 files changed, 182 insertions(+)
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin.inf b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin.inf
index e1416f0..7cf9ecf 100644
--- a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin.inf
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin.inf
@@ -19,6 +19,7 @@
[Sources]
Armada80x0McBin/Dsdt.asl
+ Armada80x0McBin/Mcfg.aslc
Fadt.aslc
Gtdt.aslc
Madt.aslc
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h
new file mode 100644
index 0000000..d7b6124
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h
@@ -0,0 +1,26 @@
+/**
+
+ Copyright (C) 2019, Marvell International Ltd. and its affiliates.
+
+ This program and the accompanying materials are licensed and made available
+ under the terms and conditions of the BSD License which accompanies this
+ distribution. The full text of the license may be found at
+ http://opensource.org/licenses/bsd-license.php
+
+ THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+ WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+
+#define PCI_BUS_MIN 0x0
+#define PCI_BUS_MAX 0x0
+#define PCI_BUS_COUNT 0x1
+#define PCI_MMIO32_BASE 0xC0000000
+#define PCI_MMIO32_SIZE 0x20000000
+#define PCI_MMIO64_BASE 0x800000000
+#define PCI_MMIO64_SIZE 0x100000000
+#define PCI_IO_BASE 0x0
+#define PCI_IO_SIZE 0x10000
+#define PCI_IO_TRANSLATION 0xEFF00000
+#define PCI_ECAM_BASE 0xE0008000
+#define PCI_ECAM_SIZE 0x10000000
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Dsdt.asl b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Dsdt.asl
index 638698a..f7cffb9 100644
--- a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Dsdt.asl
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Dsdt.asl
@@ -8,6 +8,7 @@
**/
+#include "Armada80x0McBin/Pcie.h"
#include "IcuInterrupts.h"
DefinitionBlock ("DSDT.aml", "DSDT", 2, "MVEBU ", "ARMADA8K", 3)
@@ -300,5 +301,112 @@ DefinitionBlock ("DSDT.aml", "DSDT", 2, "MVEBU ", "ARMADA8K", 3)
}
})
}
+
+ //
+ // PCIe Root Bus
+ //
+ Device (PCI0)
+ {
+ Name (_HID, "PNP0A08" /* PCI Express Bus */) // _HID: Hardware ID
+ Name (_CID, "PNP0A03" /* PCI Bus */) // _CID: Compatible ID
+ Name (_SEG, 0x00) // _SEG: PCI Segment
+ Name (_BBN, 0x00) // _BBN: BIOS Bus Number
+ Name (_CCA, 0x01) // _CCA: Cache Coherency Attribute
+ Name (_PRT, Package () // _PRT: PCI Routing Table
+ {
+ Package () { 0xFFFF, 0x0, 0x0, 0x40 },
+ Package () { 0xFFFF, 0x1, 0x0, 0x40 },
+ Package () { 0xFFFF, 0x2, 0x0, 0x40 },
+ Package () { 0xFFFF, 0x3, 0x0, 0x40 }
+ })
+
+ Method (_CRS, 0, Serialized) // _CRS: Current Resource Settings
+ {
+ Name (RBUF, ResourceTemplate ()
+ {
+ WordBusNumber (ResourceProducer, MinFixed, MaxFixed, PosDecode,
+ 0x0000, // Granularity
+ PCI_BUS_MIN, // Range Minimum
+ PCI_BUS_MAX, // Range Maximum
+ 0x0000, // Translation Offset
+ PCI_BUS_COUNT // Length
+ )
+ DWordMemory (ResourceProducer, PosDecode, MinFixed, MaxFixed, NonCacheable, ReadWrite,
+ 0x00000000, // Granularity
+ PCI_MMIO32_BASE, // Range Minimum
+ 0xDFFFFFFF, // Range Maximum
+ 0x00000000, // Translation Offset
+ PCI_MMIO32_SIZE // Length
+ )
+ QWordMemory (ResourceProducer, PosDecode, MinFixed, MaxFixed, NonCacheable, ReadWrite,
+ 0x0000000000000000, // Granularity
+ PCI_MMIO64_BASE, // Range Minimum
+ 0x8FFFFFFFF, // Range Maximum
+ 0x00000000, // Translation Offset
+ PCI_MMIO64_SIZE // Length
+ )
+ DWordIo (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange,
+ 0x00000000, // Granularity
+ PCI_IO_BASE, // Range Minimum
+ 0x0000FFFF, // Range Maximum
+ PCI_IO_TRANSLATION, // Translation Address
+ PCI_IO_SIZE, // Length
+ ,
+ ,
+ ,
+ TypeTranslation
+ )
+ })
+ Return (RBUF) /* \_SB_.PCI0._CRS.RBUF */
+ } // Method(_CRS)
+
+ Device (RES0)
+ {
+ Name (_HID, "PNP0C02")
+ Name (_CRS, ResourceTemplate ()
+ {
+ Memory32Fixed (ReadWrite,
+ PCI_ECAM_BASE,
+ PCI_ECAM_SIZE
+ )
+ })
+ }
+ Name (SUPP, 0x00)
+ Name (CTRL, 0x00)
+ Method (_OSC, 4, NotSerialized) // _OSC: Operating System Capabilities
+ {
+ CreateDWordField (Arg3, 0x00, CDW1)
+ If (LEqual (Arg0, ToUUID ("33db4d5b-1ff7-401c-9657-7441c03dd766") /* PCI Host Bridge Device */))
+ {
+ CreateDWordField (Arg3, 0x04, CDW2)
+ CreateDWordField (Arg3, 0x08, CDW3)
+ Store (CDW2, SUPP) /* \_SB_.PCI0.SUPP */
+ Store (CDW3, CTRL) /* \_SB_.PCI0.CTRL */
+ If (LNotEqual (And (SUPP, 0x16), 0x16))
+ {
+ And (CTRL, 0x1E, CTRL) /* \_SB_.PCI0.CTRL */
+ }
+
+ And (CTRL, 0x1D, CTRL) /* \_SB_.PCI0.CTRL */
+ If (LNotEqual (Arg1, One))
+ {
+ Or (CDW1, 0x08, CDW1) /* \_SB_.PCI0._OSC.CDW1 */
+ }
+
+ If (LNotEqual (CDW3, CTRL))
+ {
+ Or (CDW1, 0x10, CDW1) /* \_SB_.PCI0._OSC.CDW1 */
+ }
+
+ Store (CTRL, CDW3) /* \_SB_.PCI0._OSC.CDW3 */
+ Return (Arg3)
+ }
+ Else
+ {
+ Or (CDW1, 0x04, CDW1) /* \_SB_.PCI0._OSC.CDW1 */
+ Return (Arg3)
+ }
+ } // Method(_OSC)
+ }
}
}
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc
new file mode 100644
index 0000000..bda5800
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc
@@ -0,0 +1,47 @@
+/** @file
+
+ Memory mapped config space base address table (MCFG)
+
+ Copyright (c) 2017, Linaro Ltd. All rights reserved.<BR>
+ Copyright (c) 2019, Marvell International Ltd. and its affiliates.<BR>
+
+ This program and the accompanying materials
+ are licensed and made available under the terms and conditions of the BSD License
+ which accompanies this distribution. The full text of the license may be found at
+ http://opensource.org/licenses/bsd-license.php
+
+ THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+ WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+
+#include <Library/AcpiLib.h>
+
+#include "AcpiHeader.h"
+#include "Armada80x0McBin/Pcie.h"
+
+#include <IndustryStandard/MemoryMappedConfigurationSpaceAccessTable.h>
+
+#pragma pack(1)
+typedef struct {
+ EFI_ACPI_MEMORY_MAPPED_CONFIGURATION_BASE_ADDRESS_TABLE_HEADER Header;
+ EFI_ACPI_MEMORY_MAPPED_ENHANCED_CONFIGURATION_SPACE_BASE_ADDRESS_ALLOCATION_STRUCTURE Structure;
+} ACPI_6_0_MCFG_STRUCTURE;
+#pragma pack()
+
+STATIC ACPI_6_0_MCFG_STRUCTURE Mcfg = {
+ {
+ __ACPI_HEADER (EFI_ACPI_5_0_PCI_EXPRESS_MEMORY_MAPPED_CONFIGURATION_SPACE_BASE_ADDRESS_DESCRIPTION_TABLE_SIGNATURE,
+ ACPI_6_0_MCFG_STRUCTURE,
+ EFI_ACPI_MEMORY_MAPPED_CONFIGURATION_SPACE_ACCESS_TABLE_REVISION),
+ EFI_ACPI_RESERVED_QWORD
+ }, {
+ PCI_ECAM_BASE, // BaseAddress
+ 0, // PciSegmentGroupNumber
+ PCI_BUS_MIN, // StartBusNumber
+ PCI_BUS_MAX, // EndBusNumber
+ EFI_ACPI_RESERVED_DWORD // Reserved
+ }
+};
+
+VOID CONST * CONST ReferenceAcpiTable = &Mcfg;
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 10/14] Marvell/Armada80x0Db: Enable ACPI PCIE support
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (8 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 09/14] Marvell/Armada80x0McBin: Enable ACPI " Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 11/14] Marvell/Armada70x0Db: " Marcin Wojtas
` (4 subsequent siblings)
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
This patch adds description of the PCIE controller in
ACPI tables of Armada 8040 DB board.
Due to the quirky nature of the Synopsys Designware PCIe IP,
the type 0 configuration is broadcast and whatever device
is plugged into slot, will appear at each 32 device
positions of bus0.
In order to prevent above, shift the config space base address
to the second half of the smallest ATU window (64kB), and limit
bus number to 1. Thanks to this, the pci-host-generic driver
could be used in OS with ACPI, however with the limitation
to support only single device in the slot.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db.inf | 1 +
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h | 26 +++++
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Dsdt.asl | 108 ++++++++++++++++++++
Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc | 47 +++++++++
4 files changed, 182 insertions(+)
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db.inf b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db.inf
index 8367f07..7750817 100644
--- a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db.inf
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db.inf
@@ -19,6 +19,7 @@
[Sources]
Armada80x0Db/Dsdt.asl
+ Armada80x0Db/Mcfg.aslc
Fadt.aslc
Gtdt.aslc
Madt.aslc
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h
new file mode 100644
index 0000000..d7b6124
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h
@@ -0,0 +1,26 @@
+/**
+
+ Copyright (C) 2019, Marvell International Ltd. and its affiliates.
+
+ This program and the accompanying materials are licensed and made available
+ under the terms and conditions of the BSD License which accompanies this
+ distribution. The full text of the license may be found at
+ http://opensource.org/licenses/bsd-license.php
+
+ THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+ WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+
+#define PCI_BUS_MIN 0x0
+#define PCI_BUS_MAX 0x0
+#define PCI_BUS_COUNT 0x1
+#define PCI_MMIO32_BASE 0xC0000000
+#define PCI_MMIO32_SIZE 0x20000000
+#define PCI_MMIO64_BASE 0x800000000
+#define PCI_MMIO64_SIZE 0x100000000
+#define PCI_IO_BASE 0x0
+#define PCI_IO_SIZE 0x10000
+#define PCI_IO_TRANSLATION 0xEFF00000
+#define PCI_ECAM_BASE 0xE0008000
+#define PCI_ECAM_SIZE 0x10000000
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Dsdt.asl b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Dsdt.asl
index 822a8e4..5c060a3 100644
--- a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Dsdt.asl
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Dsdt.asl
@@ -9,6 +9,7 @@
**/
+#include "Armada80x0Db/Pcie.h"
#include "IcuInterrupts.h"
DefinitionBlock ("DSDT.aml", "DSDT", 2, "MVEBU ", "ARMADA8K", 3)
@@ -320,5 +321,112 @@ DefinitionBlock ("DSDT.aml", "DSDT", 2, "MVEBU ", "ARMADA8K", 3)
}
})
}
+
+ //
+ // PCIe Root Bus
+ //
+ Device (PCI0)
+ {
+ Name (_HID, "PNP0A08" /* PCI Express Bus */) // _HID: Hardware ID
+ Name (_CID, "PNP0A03" /* PCI Bus */) // _CID: Compatible ID
+ Name (_SEG, 0x00) // _SEG: PCI Segment
+ Name (_BBN, 0x00) // _BBN: BIOS Bus Number
+ Name (_CCA, 0x01) // _CCA: Cache Coherency Attribute
+ Name (_PRT, Package () // _PRT: PCI Routing Table
+ {
+ Package () { 0xFFFF, 0x0, 0x0, 0x40 },
+ Package () { 0xFFFF, 0x1, 0x0, 0x40 },
+ Package () { 0xFFFF, 0x2, 0x0, 0x40 },
+ Package () { 0xFFFF, 0x3, 0x0, 0x40 }
+ })
+
+ Method (_CRS, 0, Serialized) // _CRS: Current Resource Settings
+ {
+ Name (RBUF, ResourceTemplate ()
+ {
+ WordBusNumber (ResourceProducer, MinFixed, MaxFixed, PosDecode,
+ 0x0000, // Granularity
+ PCI_BUS_MIN, // Range Minimum
+ PCI_BUS_MAX, // Range Maximum
+ 0x0000, // Translation Offset
+ PCI_BUS_COUNT // Length
+ )
+ DWordMemory (ResourceProducer, PosDecode, MinFixed, MaxFixed, NonCacheable, ReadWrite,
+ 0x00000000, // Granularity
+ PCI_MMIO32_BASE, // Range Minimum
+ 0xDFFFFFFF, // Range Maximum
+ 0x00000000, // Translation Offset
+ PCI_MMIO32_SIZE // Length
+ )
+ QWordMemory (ResourceProducer, PosDecode, MinFixed, MaxFixed, NonCacheable, ReadWrite,
+ 0x0000000000000000, // Granularity
+ PCI_MMIO64_BASE, // Range Minimum
+ 0x8FFFFFFFF, // Range Maximum
+ 0x00000000, // Translation Offset
+ PCI_MMIO64_SIZE // Length
+ )
+ DWordIo (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange,
+ 0x00000000, // Granularity
+ PCI_IO_BASE, // Range Minimum
+ 0x0000FFFF, // Range Maximum
+ PCI_IO_TRANSLATION, // Translation Address
+ PCI_IO_SIZE, // Length
+ ,
+ ,
+ ,
+ TypeTranslation
+ )
+ })
+ Return (RBUF) /* \_SB_.PCI0._CRS.RBUF */
+ } // Method(_CRS)
+
+ Device (RES0)
+ {
+ Name (_HID, "PNP0C02")
+ Name (_CRS, ResourceTemplate ()
+ {
+ Memory32Fixed (ReadWrite,
+ PCI_ECAM_BASE,
+ PCI_ECAM_SIZE
+ )
+ })
+ }
+ Name (SUPP, 0x00)
+ Name (CTRL, 0x00)
+ Method (_OSC, 4, NotSerialized) // _OSC: Operating System Capabilities
+ {
+ CreateDWordField (Arg3, 0x00, CDW1)
+ If (LEqual (Arg0, ToUUID ("33db4d5b-1ff7-401c-9657-7441c03dd766") /* PCI Host Bridge Device */))
+ {
+ CreateDWordField (Arg3, 0x04, CDW2)
+ CreateDWordField (Arg3, 0x08, CDW3)
+ Store (CDW2, SUPP) /* \_SB_.PCI0.SUPP */
+ Store (CDW3, CTRL) /* \_SB_.PCI0.CTRL */
+ If (LNotEqual (And (SUPP, 0x16), 0x16))
+ {
+ And (CTRL, 0x1E, CTRL) /* \_SB_.PCI0.CTRL */
+ }
+
+ And (CTRL, 0x1D, CTRL) /* \_SB_.PCI0.CTRL */
+ If (LNotEqual (Arg1, One))
+ {
+ Or (CDW1, 0x08, CDW1) /* \_SB_.PCI0._OSC.CDW1 */
+ }
+
+ If (LNotEqual (CDW3, CTRL))
+ {
+ Or (CDW1, 0x10, CDW1) /* \_SB_.PCI0._OSC.CDW1 */
+ }
+
+ Store (CTRL, CDW3) /* \_SB_.PCI0._OSC.CDW3 */
+ Return (Arg3)
+ }
+ Else
+ {
+ Or (CDW1, 0x04, CDW1) /* \_SB_.PCI0._OSC.CDW1 */
+ Return (Arg3)
+ }
+ } // Method(_OSC)
+ }
}
}
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc
new file mode 100644
index 0000000..da152b7
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc
@@ -0,0 +1,47 @@
+/** @file
+
+ Memory mapped config space base address table (MCFG)
+
+ Copyright (c) 2017, Linaro Ltd. All rights reserved.<BR>
+ Copyright (c) 2019, Marvell International Ltd. and its affiliates.<BR>
+
+ This program and the accompanying materials
+ are licensed and made available under the terms and conditions of the BSD License
+ which accompanies this distribution. The full text of the license may be found at
+ http://opensource.org/licenses/bsd-license.php
+
+ THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+ WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+
+#include <Library/AcpiLib.h>
+
+#include "AcpiHeader.h"
+#include "Armada80x0Db/Pcie.h"
+
+#include <IndustryStandard/MemoryMappedConfigurationSpaceAccessTable.h>
+
+#pragma pack(1)
+typedef struct {
+ EFI_ACPI_MEMORY_MAPPED_CONFIGURATION_BASE_ADDRESS_TABLE_HEADER Header;
+ EFI_ACPI_MEMORY_MAPPED_ENHANCED_CONFIGURATION_SPACE_BASE_ADDRESS_ALLOCATION_STRUCTURE Structure;
+} ACPI_6_0_MCFG_STRUCTURE;
+#pragma pack()
+
+STATIC ACPI_6_0_MCFG_STRUCTURE Mcfg = {
+ {
+ __ACPI_HEADER (EFI_ACPI_5_0_PCI_EXPRESS_MEMORY_MAPPED_CONFIGURATION_SPACE_BASE_ADDRESS_DESCRIPTION_TABLE_SIGNATURE,
+ ACPI_6_0_MCFG_STRUCTURE,
+ EFI_ACPI_MEMORY_MAPPED_CONFIGURATION_SPACE_ACCESS_TABLE_REVISION),
+ EFI_ACPI_RESERVED_QWORD
+ }, {
+ PCI_ECAM_BASE, // BaseAddress
+ 0, // PciSegmentGroupNumber
+ PCI_BUS_MIN, // StartBusNumber
+ PCI_BUS_MAX, // EndBusNumber
+ EFI_ACPI_RESERVED_DWORD // Reserved
+ }
+};
+
+VOID CONST * CONST ReferenceAcpiTable = &Mcfg;
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 11/14] Marvell/Armada70x0Db: Enable ACPI PCIE support
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (9 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 10/14] Marvell/Armada80x0Db: " Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 12/14] Marvell/Armada80x0McBin: DeviceTree: Use pci-host-generic driver Marcin Wojtas
` (3 subsequent siblings)
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
This patch adds description of the PCIE controller in
ACPI tables of Armada 7040 DB board.
Due to the quirky nature of the Synopsys Designware PCIe IP,
the type 0 configuration is broadcast and whatever device
is plugged into slot, will appear at each 32 device
positions of bus0.
In order to prevent above, shift the config space base address
to the second half of the smallest ATU window (64kB), and limit
bus number to 1. Thanks to this, the pci-host-generic driver
could be used in OS with ACPI, however with the limitation
to support only single device in the slot.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db.inf | 1 +
Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h | 26 +++++
Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Dsdt.asl | 108 ++++++++++++++++++++
Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc | 47 +++++++++
4 files changed, 182 insertions(+)
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h
create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db.inf b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db.inf
index 926f366..f3cce52 100644
--- a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db.inf
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db.inf
@@ -19,6 +19,7 @@
[Sources]
Armada70x0Db/Dsdt.asl
+ Armada70x0Db/Mcfg.aslc
Fadt.aslc
Gtdt.aslc
Madt.aslc
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h
new file mode 100644
index 0000000..d7b6124
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h
@@ -0,0 +1,26 @@
+/**
+
+ Copyright (C) 2019, Marvell International Ltd. and its affiliates.
+
+ This program and the accompanying materials are licensed and made available
+ under the terms and conditions of the BSD License which accompanies this
+ distribution. The full text of the license may be found at
+ http://opensource.org/licenses/bsd-license.php
+
+ THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+ WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+
+#define PCI_BUS_MIN 0x0
+#define PCI_BUS_MAX 0x0
+#define PCI_BUS_COUNT 0x1
+#define PCI_MMIO32_BASE 0xC0000000
+#define PCI_MMIO32_SIZE 0x20000000
+#define PCI_MMIO64_BASE 0x800000000
+#define PCI_MMIO64_SIZE 0x100000000
+#define PCI_IO_BASE 0x0
+#define PCI_IO_SIZE 0x10000
+#define PCI_IO_TRANSLATION 0xEFF00000
+#define PCI_ECAM_BASE 0xE0008000
+#define PCI_ECAM_SIZE 0x10000000
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Dsdt.asl b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Dsdt.asl
index 20369c5..90b191b 100644
--- a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Dsdt.asl
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Dsdt.asl
@@ -9,6 +9,7 @@
**/
+#include "Armada70x0Db/Pcie.h"
#include "IcuInterrupts.h"
DefinitionBlock ("DSDT.aml", "DSDT", 2, "MVEBU ", "ARMADA7K", 3)
@@ -219,5 +220,112 @@ DefinitionBlock ("DSDT.aml", "DSDT", 2, "MVEBU ", "ARMADA7K", 3)
}
})
}
+
+ //
+ // PCIe Root Bus
+ //
+ Device (PCI0)
+ {
+ Name (_HID, "PNP0A08" /* PCI Express Bus */) // _HID: Hardware ID
+ Name (_CID, "PNP0A03" /* PCI Bus */) // _CID: Compatible ID
+ Name (_SEG, 0x00) // _SEG: PCI Segment
+ Name (_BBN, 0x00) // _BBN: BIOS Bus Number
+ Name (_CCA, 0x01) // _CCA: Cache Coherency Attribute
+ Name (_PRT, Package () // _PRT: PCI Routing Table
+ {
+ Package () { 0xFFFF, 0x0, 0x0, 0x40 },
+ Package () { 0xFFFF, 0x1, 0x0, 0x40 },
+ Package () { 0xFFFF, 0x2, 0x0, 0x40 },
+ Package () { 0xFFFF, 0x3, 0x0, 0x40 }
+ })
+
+ Method (_CRS, 0, Serialized) // _CRS: Current Resource Settings
+ {
+ Name (RBUF, ResourceTemplate ()
+ {
+ WordBusNumber (ResourceProducer, MinFixed, MaxFixed, PosDecode,
+ 0x0000, // Granularity
+ PCI_BUS_MIN, // Range Minimum
+ PCI_BUS_MAX, // Range Maximum
+ 0x0000, // Translation Offset
+ PCI_BUS_COUNT // Length
+ )
+ DWordMemory (ResourceProducer, PosDecode, MinFixed, MaxFixed, NonCacheable, ReadWrite,
+ 0x00000000, // Granularity
+ PCI_MMIO32_BASE, // Range Minimum
+ 0xDFFFFFFF, // Range Maximum
+ 0x00000000, // Translation Offset
+ PCI_MMIO32_SIZE // Length
+ )
+ QWordMemory (ResourceProducer, PosDecode, MinFixed, MaxFixed, NonCacheable, ReadWrite,
+ 0x0000000000000000, // Granularity
+ PCI_MMIO64_BASE, // Range Minimum
+ 0x8FFFFFFFF, // Range Maximum
+ 0x00000000, // Translation Offset
+ PCI_MMIO64_SIZE // Length
+ )
+ DWordIo (ResourceProducer, MinFixed, MaxFixed, PosDecode, EntireRange,
+ 0x00000000, // Granularity
+ PCI_IO_BASE, // Range Minimum
+ 0x0000FFFF, // Range Maximum
+ PCI_IO_TRANSLATION, // Translation Address
+ PCI_IO_SIZE, // Length
+ ,
+ ,
+ ,
+ TypeTranslation
+ )
+ })
+ Return (RBUF) /* \_SB_.PCI0._CRS.RBUF */
+ } // Method(_CRS)
+
+ Device (RES0)
+ {
+ Name (_HID, "PNP0C02")
+ Name (_CRS, ResourceTemplate ()
+ {
+ Memory32Fixed (ReadWrite,
+ PCI_ECAM_BASE,
+ PCI_ECAM_SIZE
+ )
+ })
+ }
+ Name (SUPP, 0x00)
+ Name (CTRL, 0x00)
+ Method (_OSC, 4, NotSerialized) // _OSC: Operating System Capabilities
+ {
+ CreateDWordField (Arg3, 0x00, CDW1)
+ If (LEqual (Arg0, ToUUID ("33db4d5b-1ff7-401c-9657-7441c03dd766") /* PCI Host Bridge Device */))
+ {
+ CreateDWordField (Arg3, 0x04, CDW2)
+ CreateDWordField (Arg3, 0x08, CDW3)
+ Store (CDW2, SUPP) /* \_SB_.PCI0.SUPP */
+ Store (CDW3, CTRL) /* \_SB_.PCI0.CTRL */
+ If (LNotEqual (And (SUPP, 0x16), 0x16))
+ {
+ And (CTRL, 0x1E, CTRL) /* \_SB_.PCI0.CTRL */
+ }
+
+ And (CTRL, 0x1D, CTRL) /* \_SB_.PCI0.CTRL */
+ If (LNotEqual (Arg1, One))
+ {
+ Or (CDW1, 0x08, CDW1) /* \_SB_.PCI0._OSC.CDW1 */
+ }
+
+ If (LNotEqual (CDW3, CTRL))
+ {
+ Or (CDW1, 0x10, CDW1) /* \_SB_.PCI0._OSC.CDW1 */
+ }
+
+ Store (CTRL, CDW3) /* \_SB_.PCI0._OSC.CDW3 */
+ Return (Arg3)
+ }
+ Else
+ {
+ Or (CDW1, 0x04, CDW1) /* \_SB_.PCI0._OSC.CDW1 */
+ Return (Arg3)
+ }
+ } // Method(_OSC)
+ }
}
}
diff --git a/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc
new file mode 100644
index 0000000..90bf163
--- /dev/null
+++ b/Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc
@@ -0,0 +1,47 @@
+/** @file
+
+ Memory mapped config space base address table (MCFG)
+
+ Copyright (c) 2017, Linaro Ltd. All rights reserved.<BR>
+ Copyright (c) 2019, Marvell International Ltd. and its affiliates.<BR>
+
+ This program and the accompanying materials
+ are licensed and made available under the terms and conditions of the BSD License
+ which accompanies this distribution. The full text of the license may be found at
+ http://opensource.org/licenses/bsd-license.php
+
+ THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+ WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+
+#include <Library/AcpiLib.h>
+
+#include "AcpiHeader.h"
+#include "Armada70x0Db/Pcie.h"
+
+#include <IndustryStandard/MemoryMappedConfigurationSpaceAccessTable.h>
+
+#pragma pack(1)
+typedef struct {
+ EFI_ACPI_MEMORY_MAPPED_CONFIGURATION_BASE_ADDRESS_TABLE_HEADER Header;
+ EFI_ACPI_MEMORY_MAPPED_ENHANCED_CONFIGURATION_SPACE_BASE_ADDRESS_ALLOCATION_STRUCTURE Structure;
+} ACPI_6_0_MCFG_STRUCTURE;
+#pragma pack()
+
+STATIC ACPI_6_0_MCFG_STRUCTURE Mcfg = {
+ {
+ __ACPI_HEADER (EFI_ACPI_5_0_PCI_EXPRESS_MEMORY_MAPPED_CONFIGURATION_SPACE_BASE_ADDRESS_DESCRIPTION_TABLE_SIGNATURE,
+ ACPI_6_0_MCFG_STRUCTURE,
+ EFI_ACPI_MEMORY_MAPPED_CONFIGURATION_SPACE_ACCESS_TABLE_REVISION),
+ EFI_ACPI_RESERVED_QWORD
+ }, {
+ PCI_ECAM_BASE, // BaseAddress
+ 0, // PciSegmentGroupNumber
+ PCI_BUS_MIN, // StartBusNumber
+ PCI_BUS_MAX, // EndBusNumber
+ EFI_ACPI_RESERVED_DWORD // Reserved
+ }
+};
+
+VOID CONST * CONST ReferenceAcpiTable = &Mcfg;
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 12/14] Marvell/Armada80x0McBin: DeviceTree: Use pci-host-generic driver
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (10 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 11/14] Marvell/Armada70x0Db: " Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 13/14] Marvell/Armada7k8k: Remove duplication in .dsc files Marcin Wojtas
` (2 subsequent siblings)
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
Now as the OS clock configuration is inherited from the firmware,
and PCIE is also configured, switch safely MacchiatoBin board to
use the pci-host-generic driver.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Armada7k8k/DeviceTree/armada-8040-mcbin.dts | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Silicon/Marvell/Armada7k8k/DeviceTree/armada-8040-mcbin.dts b/Silicon/Marvell/Armada7k8k/DeviceTree/armada-8040-mcbin.dts
index b86e27e..d9c9348 100644
--- a/Silicon/Marvell/Armada7k8k/DeviceTree/armada-8040-mcbin.dts
+++ b/Silicon/Marvell/Armada7k8k/DeviceTree/armada-8040-mcbin.dts
@@ -180,6 +180,9 @@
};
&cp0_pcie0 {
+ compatible = "marvell,armada8k-pcie-ecam", "snps,dw-pcie-ecam";
+ reg = <0 0xe0000000 0 0xff00000>;
+ bus-range = <0 0xfe>;
pinctrl-names = "default";
pinctrl-0 = <&cp0_pcie_pins>;
num-lanes = <4>;
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 13/14] Marvell/Armada7k8k: Remove duplication in .dsc files
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (11 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 12/14] Marvell/Armada80x0McBin: DeviceTree: Use pci-host-generic driver Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 14/14] Marvell/Armada7k8: Add 'acpiview' shell command to build Marcin Wojtas
2019-05-23 13:27 ` [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Mark Kettenis
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
Mistakenly in all Marvell Armada7k8k .dsc files
'[LibraryClasses.common]' section was split.
Merge entries into one for each platform.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Platform/Marvell/Armada70x0Db/Armada70x0Db.dsc | 4 +---
Platform/Marvell/Armada80x0Db/Armada80x0Db.dsc | 4 +---
Platform/SolidRun/Armada80x0McBin/Armada80x0McBin.dsc | 4 +---
3 files changed, 3 insertions(+), 9 deletions(-)
diff --git a/Platform/Marvell/Armada70x0Db/Armada70x0Db.dsc b/Platform/Marvell/Armada70x0Db/Armada70x0Db.dsc
index 01532b4..9ceb872 100644
--- a/Platform/Marvell/Armada70x0Db/Armada70x0Db.dsc
+++ b/Platform/Marvell/Armada70x0Db/Armada70x0Db.dsc
@@ -48,9 +48,6 @@
!include Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc
-[LibraryClasses.common]
- NonDiscoverableInitLib|Platform/Marvell/Armada70x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.inf
-
[Components.common]
Silicon/Marvell/Armada7k8k/DeviceTree/Armada70x0Db.inf
@@ -59,6 +56,7 @@
[LibraryClasses.common]
ArmadaBoardDescLib|Platform/Marvell/Armada70x0Db/Armada70x0DbBoardDescLib/Armada70x0DbBoardDescLib.inf
+ NonDiscoverableInitLib|Platform/Marvell/Armada70x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.inf
################################################################################
#
diff --git a/Platform/Marvell/Armada80x0Db/Armada80x0Db.dsc b/Platform/Marvell/Armada80x0Db/Armada80x0Db.dsc
index c6510bb..6487321 100644
--- a/Platform/Marvell/Armada80x0Db/Armada80x0Db.dsc
+++ b/Platform/Marvell/Armada80x0Db/Armada80x0Db.dsc
@@ -48,9 +48,6 @@
!include Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc
-[LibraryClasses.common]
- NonDiscoverableInitLib|Platform/Marvell/Armada80x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.inf
-
[Components.common]
Silicon/Marvell/Armada7k8k/DeviceTree/Armada80x0Db.inf
@@ -59,6 +56,7 @@
[LibraryClasses.common]
ArmadaBoardDescLib|Platform/Marvell/Armada80x0Db/Armada80x0DbBoardDescLib/Armada80x0DbBoardDescLib.inf
+ NonDiscoverableInitLib|Platform/Marvell/Armada80x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.inf
################################################################################
#
diff --git a/Platform/SolidRun/Armada80x0McBin/Armada80x0McBin.dsc b/Platform/SolidRun/Armada80x0McBin/Armada80x0McBin.dsc
index d080136..cb41f4e 100644
--- a/Platform/SolidRun/Armada80x0McBin/Armada80x0McBin.dsc
+++ b/Platform/SolidRun/Armada80x0McBin/Armada80x0McBin.dsc
@@ -49,9 +49,6 @@
!include Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc
-[LibraryClasses.common]
- NonDiscoverableInitLib|Platform/SolidRun/Armada80x0McBin/NonDiscoverableInitLib/NonDiscoverableInitLib.inf
-
[Components.common]
Silicon/Marvell/Armada7k8k/DeviceTree/Armada80x0McBin.inf
@@ -60,6 +57,7 @@
[LibraryClasses.common]
ArmadaBoardDescLib|Platform/SolidRun/Armada80x0McBin/Armada80x0McBinBoardDescLib/Armada80x0McBinBoardDescLib.inf
+ NonDiscoverableInitLib|Platform/SolidRun/Armada80x0McBin/NonDiscoverableInitLib/NonDiscoverableInitLib.inf
################################################################################
#
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [edk2-platforms: PATCH v2 14/14] Marvell/Armada7k8: Add 'acpiview' shell command to build
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (12 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 13/14] Marvell/Armada7k8k: Remove duplication in .dsc files Marcin Wojtas
@ 2019-05-20 15:27 ` Marcin Wojtas
2019-05-23 13:27 ` [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Mark Kettenis
14 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-20 15:27 UTC (permalink / raw)
To: devel
Cc: leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap, Jici.Gao,
rebecca, kettenis
To help diagnose ACPI related boot problems, include the 'acpiview'
builtin shell command to Armada7k8k build of the UEFI Shell.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
---
Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc | 1 +
1 file changed, 1 insertion(+)
diff --git a/Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc b/Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc
index 757c6b2..a5bb9f2 100644
--- a/Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc
+++ b/Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc
@@ -592,6 +592,7 @@
ShellPkg/Application/Shell/Shell.inf {
<LibraryClasses>
ShellCommandLib|ShellPkg/Library/UefiShellCommandLib/UefiShellCommandLib.inf
+ NULL|ShellPkg/Library/UefiShellAcpiViewCommandLib/UefiShellAcpiViewCommandLib.inf
NULL|ShellPkg/Library/UefiShellLevel2CommandsLib/UefiShellLevel2CommandsLib.inf
NULL|ShellPkg/Library/UefiShellLevel1CommandsLib/UefiShellLevel1CommandsLib.inf
NULL|ShellPkg/Library/UefiShellLevel3CommandsLib/UefiShellLevel3CommandsLib.inf
--
2.7.4
^ permalink raw reply related [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
` (13 preceding siblings ...)
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 14/14] Marvell/Armada7k8: Add 'acpiview' shell command to build Marcin Wojtas
@ 2019-05-23 13:27 ` Mark Kettenis
2019-05-23 14:14 ` Leif Lindholm
14 siblings, 1 reply; 34+ messages in thread
From: Mark Kettenis @ 2019-05-23 13:27 UTC (permalink / raw)
To: Marcin Wojtas
Cc: devel, leif.lindholm, ard.biesheuvel, mw, jsd, jaz, kostap,
Jici.Gao, rebecca
> From: Marcin Wojtas <mw@semihalf.com>
> Date: Mon, 20 May 2019 17:27:13 +0200
>
> Hi,
>
> Thank you for thorough review of v1. I submit second
> version of the Armada7k8k PCIE support. I addressed
> all comments. There is no functional change to initial
> patchset, but mostly clean-up and improvements - please
> refer to the changelog below.
>
> The patches are available in the github:
> https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/commits/pcie-upstream-r20190520
>
> I'm looking forward to your comments or remarks.
>
> Best regards,
> Marcin
Tested this on my mcbin running OpenBSD. It incovers a small issue in
our kernel which I'm fixing. Otherwise this seems to work fine.
So tested-by: Mark Kettenis <kettenis@openbsd.org> if that matters.
Cheers,
Mark
> Changelog:
> v1->v2:
> *All
> - s/PcieBaseAddress/PcieDbiAdress/
>
> *2/14
> - fix alignment in comment
>
> * 3/14
> - add CONST** to library callback
>
> * 4/14
> - add missing reset GPIO to McBin description
>
> * 5/15
> - add CONST** to protocol callback
>
> * 6/14
> - cleanup all casting in file
> - use MAX_UINTx macros
> - add Linaro copyright
> - use MmioWrite8 instead of volatile in PciExpressReadBuffer
> - correct commient in IgnoreBusDeviceFunction ()
> - fix typo in commit message
>
> * 7/10
> - correct line endings
> - use temporary variable for memory description in PciHostBridgeResourceConflict
> - use MAX_UINTx macros
> - add comments around stalls and MemoryFence in GPIO reset
> - keep the reset active for 150ms
> - assign translation values instead of asserting
>
> *8/14
> - assign gArmTokenSpaceGuid.PcdPciIoTranslation value in .dsc
>
> * 9-11/14
> - correct line endings
> - remove unused methods
> - extend commit messages with 32k shift description
>
> Ard Biesheuvel (1):
> Marvell/Armada7k8k: Add PciExpressLib implementation
>
> Marcin Wojtas (13):
> Marvell/Library: MvGpioLib: Extend GPIO pin description
> Marvell/Library: ArmadaSoCDescLib: Add PCIE information
> Marvell/Library: ArmadaBoardDescLib: Add PCIE information
> Marvell/Armada7k8k: Extend board description libraries with PCIE
> Marvell/Armada7k8k: MvBoardDesc: Extend protocol with PCIE support
> Marvell/Armada7k8k: Implement PciHostBridgeLib
> Marvell/Armada7k8k: Enable PCIE support
> Marvell/Armada80x0McBin: Enable ACPI PCIE support
> Marvell/Armada80x0Db: Enable ACPI PCIE support
> Marvell/Armada70x0Db: Enable ACPI PCIE support
> Marvell/Armada80x0McBin: DeviceTree: Use pci-host-generic driver
> Marvell/Armada7k8k: Remove duplication in .dsc files
> Marvell/Armada7k8: Add 'acpiview' shell command to build
>
> Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc | 19 +-
> Platform/Marvell/Armada70x0Db/Armada70x0Db.dsc | 4 +-
> Platform/Marvell/Armada80x0Db/Armada80x0Db.dsc | 4 +-
> Platform/SolidRun/Armada80x0McBin/Armada80x0McBin.dsc | 4 +-
> Silicon/Marvell/Armada7k8k/Armada7k8k.fdf | 5 +
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db.inf | 1 +
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db.inf | 1 +
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin.inf | 1 +
> Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf | 42 +
> Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf | 52 +
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h | 26 +
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h | 26 +
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h | 26 +
> Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h | 95 ++
> Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.h | 6 +
> Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h | 46 +
> Silicon/Marvell/Include/Library/ArmadaSoCDescLib.h | 20 +
> Silicon/Marvell/Include/Library/MvGpioLib.h | 1 +
> Silicon/Marvell/Include/Protocol/BoardDesc.h | 22 +
> Platform/Marvell/Armada70x0Db/Armada70x0DbBoardDescLib/Armada70x0DbBoardDescLib.c | 48 +
> Platform/Marvell/Armada70x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 4 +
> Platform/Marvell/Armada80x0Db/Armada80x0DbBoardDescLib/Armada80x0DbBoardDescLib.c | 48 +
> Platform/Marvell/Armada80x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 6 +
> Platform/SolidRun/Armada80x0McBin/Armada80x0McBinBoardDescLib/Armada80x0McBinBoardDescLib.c | 54 +
> Platform/SolidRun/Armada80x0McBin/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 1 +
> Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c | 1531 ++++++++++++++++++++
> Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c | 265 ++++
> Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c | 345 +++++
> Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.c | 44 +
> Silicon/Marvell/Drivers/BoardDesc/MvBoardDescDxe.c | 86 ++
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Dsdt.asl | 108 ++
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc | 47 +
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Dsdt.asl | 108 ++
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc | 47 +
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Dsdt.asl | 108 ++
> Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc | 47 +
> Silicon/Marvell/Armada7k8k/DeviceTree/armada-8040-mcbin.dts | 3 +
> 37 files changed, 3290 insertions(+), 11 deletions(-)
> create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
> create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf
> create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h
> create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h
> create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h
> create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h
> create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
> create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c
> create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c
> create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc
> create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc
> create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc
>
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
2019-05-23 13:27 ` [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Mark Kettenis
@ 2019-05-23 14:14 ` Leif Lindholm
2019-05-23 18:01 ` kettenis
0 siblings, 1 reply; 34+ messages in thread
From: Leif Lindholm @ 2019-05-23 14:14 UTC (permalink / raw)
To: Mark Kettenis
Cc: Marcin Wojtas, devel, ard.biesheuvel, jsd, jaz, kostap, Jici.Gao,
rebecca
On Thu, May 23, 2019 at 03:27:47PM +0200, Mark Kettenis wrote:
> > From: Marcin Wojtas <mw@semihalf.com>
> > Date: Mon, 20 May 2019 17:27:13 +0200
> >
> > Hi,
> >
> > Thank you for thorough review of v1. I submit second
> > version of the Armada7k8k PCIE support. I addressed
> > all comments. There is no functional change to initial
> > patchset, but mostly clean-up and improvements - please
> > refer to the changelog below.
> >
> > The patches are available in the github:
> > https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/commits/pcie-upstream-r20190520
> >
> > I'm looking forward to your comments or remarks.
> >
> > Best regards,
> > Marcin
>
> Tested this on my mcbin running OpenBSD. It incovers a small issue in
> our kernel which I'm fixing. Otherwise this seems to work fine.
>
> So tested-by: Mark Kettenis <kettenis@openbsd.org> if that matters.
Always helpful, thanks.
Out of interest, what was the issue?
Could I still expect the 6.5 installer to run on this
hardware/firmware combo?
Regards,
Leif
> Cheers,
>
> Mark
>
> > Changelog:
> > v1->v2:
> > *All
> > - s/PcieBaseAddress/PcieDbiAdress/
> >
> > *2/14
> > - fix alignment in comment
> >
> > * 3/14
> > - add CONST** to library callback
> >
> > * 4/14
> > - add missing reset GPIO to McBin description
> >
> > * 5/15
> > - add CONST** to protocol callback
> >
> > * 6/14
> > - cleanup all casting in file
> > - use MAX_UINTx macros
> > - add Linaro copyright
> > - use MmioWrite8 instead of volatile in PciExpressReadBuffer
> > - correct commient in IgnoreBusDeviceFunction ()
> > - fix typo in commit message
> >
> > * 7/10
> > - correct line endings
> > - use temporary variable for memory description in PciHostBridgeResourceConflict
> > - use MAX_UINTx macros
> > - add comments around stalls and MemoryFence in GPIO reset
> > - keep the reset active for 150ms
> > - assign translation values instead of asserting
> >
> > *8/14
> > - assign gArmTokenSpaceGuid.PcdPciIoTranslation value in .dsc
> >
> > * 9-11/14
> > - correct line endings
> > - remove unused methods
> > - extend commit messages with 32k shift description
> >
> > Ard Biesheuvel (1):
> > Marvell/Armada7k8k: Add PciExpressLib implementation
> >
> > Marcin Wojtas (13):
> > Marvell/Library: MvGpioLib: Extend GPIO pin description
> > Marvell/Library: ArmadaSoCDescLib: Add PCIE information
> > Marvell/Library: ArmadaBoardDescLib: Add PCIE information
> > Marvell/Armada7k8k: Extend board description libraries with PCIE
> > Marvell/Armada7k8k: MvBoardDesc: Extend protocol with PCIE support
> > Marvell/Armada7k8k: Implement PciHostBridgeLib
> > Marvell/Armada7k8k: Enable PCIE support
> > Marvell/Armada80x0McBin: Enable ACPI PCIE support
> > Marvell/Armada80x0Db: Enable ACPI PCIE support
> > Marvell/Armada70x0Db: Enable ACPI PCIE support
> > Marvell/Armada80x0McBin: DeviceTree: Use pci-host-generic driver
> > Marvell/Armada7k8k: Remove duplication in .dsc files
> > Marvell/Armada7k8: Add 'acpiview' shell command to build
> >
> > Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc | 19 +-
> > Platform/Marvell/Armada70x0Db/Armada70x0Db.dsc | 4 +-
> > Platform/Marvell/Armada80x0Db/Armada80x0Db.dsc | 4 +-
> > Platform/SolidRun/Armada80x0McBin/Armada80x0McBin.dsc | 4 +-
> > Silicon/Marvell/Armada7k8k/Armada7k8k.fdf | 5 +
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db.inf | 1 +
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db.inf | 1 +
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin.inf | 1 +
> > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf | 42 +
> > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf | 52 +
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h | 26 +
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h | 26 +
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h | 26 +
> > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h | 95 ++
> > Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.h | 6 +
> > Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h | 46 +
> > Silicon/Marvell/Include/Library/ArmadaSoCDescLib.h | 20 +
> > Silicon/Marvell/Include/Library/MvGpioLib.h | 1 +
> > Silicon/Marvell/Include/Protocol/BoardDesc.h | 22 +
> > Platform/Marvell/Armada70x0Db/Armada70x0DbBoardDescLib/Armada70x0DbBoardDescLib.c | 48 +
> > Platform/Marvell/Armada70x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 4 +
> > Platform/Marvell/Armada80x0Db/Armada80x0DbBoardDescLib/Armada80x0DbBoardDescLib.c | 48 +
> > Platform/Marvell/Armada80x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 6 +
> > Platform/SolidRun/Armada80x0McBin/Armada80x0McBinBoardDescLib/Armada80x0McBinBoardDescLib.c | 54 +
> > Platform/SolidRun/Armada80x0McBin/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 1 +
> > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c | 1531 ++++++++++++++++++++
> > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c | 265 ++++
> > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c | 345 +++++
> > Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.c | 44 +
> > Silicon/Marvell/Drivers/BoardDesc/MvBoardDescDxe.c | 86 ++
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Dsdt.asl | 108 ++
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc | 47 +
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Dsdt.asl | 108 ++
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc | 47 +
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Dsdt.asl | 108 ++
> > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc | 47 +
> > Silicon/Marvell/Armada7k8k/DeviceTree/armada-8040-mcbin.dts | 3 +
> > 37 files changed, 3290 insertions(+), 11 deletions(-)
> > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
> > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf
> > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h
> > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h
> > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h
> > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h
> > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
> > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c
> > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c
> > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc
> > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc
> > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc
> >
> > --
> > 2.7.4
> >
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
2019-05-23 14:14 ` Leif Lindholm
@ 2019-05-23 18:01 ` kettenis
2019-05-23 18:13 ` Ard Biesheuvel
0 siblings, 1 reply; 34+ messages in thread
From: kettenis @ 2019-05-23 18:01 UTC (permalink / raw)
To: Leif Lindholm
Cc: mw, devel, ard.biesheuvel, jsd, jaz, kostap, Jici.Gao, rebecca,
kettenis
> Date: Thu, 23 May 2019 15:14:27 +0100
> From: Leif Lindholm <leif.lindholm@linaro.org>
>
> On Thu, May 23, 2019 at 03:27:47PM +0200, Mark Kettenis wrote:
> > > From: Marcin Wojtas <mw@semihalf.com>
> > > Date: Mon, 20 May 2019 17:27:13 +0200
> > >
> > > Hi,
> > >
> > > Thank you for thorough review of v1. I submit second
> > > version of the Armada7k8k PCIE support. I addressed
> > > all comments. There is no functional change to initial
> > > patchset, but mostly clean-up and improvements - please
> > > refer to the changelog below.
> > >
> > > The patches are available in the github:
> > > https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/commits/pcie-upstream-r20190520
> > >
> > > I'm looking forward to your comments or remarks.
> > >
> > > Best regards,
> > > Marcin
> >
> > Tested this on my mcbin running OpenBSD. It incovers a small issue in
> > our kernel which I'm fixing. Otherwise this seems to work fine.
> >
> > So tested-by: Mark Kettenis <kettenis@openbsd.org> if that matters.
>
> Always helpful, thanks.
>
> Out of interest, what was the issue?
> Could I still expect the 6.5 installer to run on this
> hardware/firmware combo?
That should still work fine.
The issue is with mapping PCI ROMS, which currently fails with the new
firmware due to an oversight in the OpenBSD code. There are only a
few OpenBSD drivers that attempt to map the PCI ROM. But one of those
is radeondrm(4) and I stuck an AMD graphics card into the PCIe slot on
my machine.
There is a bit of a firmware angle to this though. The issue happens
because the PCI ROM address register has been set to 0xfffe0000. All
the writable address bits in the register are set to 1. While it is
possible that the hardware comes up in that state, I suspect this is
done by an attempt by the firmware to determine the size of the ROM
that doesn't properly restore the original contents of the register.
It may be related to the following messages that are printed by the
firmware:
Image type X64 can't be loaded on AARCH64 UEFI system.
Unloading driver at 0x00000000000
Connect: PcieRoot(0x0)/Pci(0x0,0x0): Not Found
Hmm, that's actually interesting. Maybe I should play with the X86
emulator that Ard added recently to see if that gives me a framebuffer
console.
Cheers,
Mark
> > Cheers,
> >
> > Mark
> >
> > > Changelog:
> > > v1->v2:
> > > *All
> > > - s/PcieBaseAddress/PcieDbiAdress/
> > >
> > > *2/14
> > > - fix alignment in comment
> > >
> > > * 3/14
> > > - add CONST** to library callback
> > >
> > > * 4/14
> > > - add missing reset GPIO to McBin description
> > >
> > > * 5/15
> > > - add CONST** to protocol callback
> > >
> > > * 6/14
> > > - cleanup all casting in file
> > > - use MAX_UINTx macros
> > > - add Linaro copyright
> > > - use MmioWrite8 instead of volatile in PciExpressReadBuffer
> > > - correct commient in IgnoreBusDeviceFunction ()
> > > - fix typo in commit message
> > >
> > > * 7/10
> > > - correct line endings
> > > - use temporary variable for memory description in PciHostBridgeResourceConflict
> > > - use MAX_UINTx macros
> > > - add comments around stalls and MemoryFence in GPIO reset
> > > - keep the reset active for 150ms
> > > - assign translation values instead of asserting
> > >
> > > *8/14
> > > - assign gArmTokenSpaceGuid.PcdPciIoTranslation value in .dsc
> > >
> > > * 9-11/14
> > > - correct line endings
> > > - remove unused methods
> > > - extend commit messages with 32k shift description
> > >
> > > Ard Biesheuvel (1):
> > > Marvell/Armada7k8k: Add PciExpressLib implementation
> > >
> > > Marcin Wojtas (13):
> > > Marvell/Library: MvGpioLib: Extend GPIO pin description
> > > Marvell/Library: ArmadaSoCDescLib: Add PCIE information
> > > Marvell/Library: ArmadaBoardDescLib: Add PCIE information
> > > Marvell/Armada7k8k: Extend board description libraries with PCIE
> > > Marvell/Armada7k8k: MvBoardDesc: Extend protocol with PCIE support
> > > Marvell/Armada7k8k: Implement PciHostBridgeLib
> > > Marvell/Armada7k8k: Enable PCIE support
> > > Marvell/Armada80x0McBin: Enable ACPI PCIE support
> > > Marvell/Armada80x0Db: Enable ACPI PCIE support
> > > Marvell/Armada70x0Db: Enable ACPI PCIE support
> > > Marvell/Armada80x0McBin: DeviceTree: Use pci-host-generic driver
> > > Marvell/Armada7k8k: Remove duplication in .dsc files
> > > Marvell/Armada7k8: Add 'acpiview' shell command to build
> > >
> > > Silicon/Marvell/Armada7k8k/Armada7k8k.dsc.inc | 19 +-
> > > Platform/Marvell/Armada70x0Db/Armada70x0Db.dsc | 4 +-
> > > Platform/Marvell/Armada80x0Db/Armada80x0Db.dsc | 4 +-
> > > Platform/SolidRun/Armada80x0McBin/Armada80x0McBin.dsc | 4 +-
> > > Silicon/Marvell/Armada7k8k/Armada7k8k.fdf | 5 +
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db.inf | 1 +
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db.inf | 1 +
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin.inf | 1 +
> > > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf | 42 +
> > > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf | 52 +
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h | 26 +
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h | 26 +
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h | 26 +
> > > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h | 95 ++
> > > Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.h | 6 +
> > > Silicon/Marvell/Include/Library/ArmadaBoardDescLib.h | 46 +
> > > Silicon/Marvell/Include/Library/ArmadaSoCDescLib.h | 20 +
> > > Silicon/Marvell/Include/Library/MvGpioLib.h | 1 +
> > > Silicon/Marvell/Include/Protocol/BoardDesc.h | 22 +
> > > Platform/Marvell/Armada70x0Db/Armada70x0DbBoardDescLib/Armada70x0DbBoardDescLib.c | 48 +
> > > Platform/Marvell/Armada70x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 4 +
> > > Platform/Marvell/Armada80x0Db/Armada80x0DbBoardDescLib/Armada80x0DbBoardDescLib.c | 48 +
> > > Platform/Marvell/Armada80x0Db/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 6 +
> > > Platform/SolidRun/Armada80x0McBin/Armada80x0McBinBoardDescLib/Armada80x0McBinBoardDescLib.c | 54 +
> > > Platform/SolidRun/Armada80x0McBin/NonDiscoverableInitLib/NonDiscoverableInitLib.c | 1 +
> > > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c | 1531 ++++++++++++++++++++
> > > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c | 265 ++++
> > > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c | 345 +++++
> > > Silicon/Marvell/Armada7k8k/Library/Armada7k8kSoCDescLib/Armada7k8kSoCDescLib.c | 44 +
> > > Silicon/Marvell/Drivers/BoardDesc/MvBoardDescDxe.c | 86 ++
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Dsdt.asl | 108 ++
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc | 47 +
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Dsdt.asl | 108 ++
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc | 47 +
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Dsdt.asl | 108 ++
> > > Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc | 47 +
> > > Silicon/Marvell/Armada7k8k/DeviceTree/armada-8040-mcbin.dts | 3 +
> > > 37 files changed, 3290 insertions(+), 11 deletions(-)
> > > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
> > > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.inf
> > > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Pcie.h
> > > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Pcie.h
> > > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Pcie.h
> > > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.h
> > > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
> > > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLib.c
> > > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciHostBridgeLib/PciHostBridgeLibConstructor.c
> > > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada70x0Db/Mcfg.aslc
> > > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0Db/Mcfg.aslc
> > > create mode 100644 Silicon/Marvell/Armada7k8k/AcpiTables/Armada80x0McBin/Mcfg.aslc
> > >
> > > --
> > > 2.7.4
> > >
>
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
2019-05-23 18:01 ` kettenis
@ 2019-05-23 18:13 ` Ard Biesheuvel
2019-05-23 20:11 ` Leif Lindholm
2019-05-24 22:16 ` mark.kettenis
0 siblings, 2 replies; 34+ messages in thread
From: Ard Biesheuvel @ 2019-05-23 18:13 UTC (permalink / raw)
To: Mark Kettenis
Cc: Leif Lindholm, Marcin Wojtas, edk2-devel-groups-io,
Jan Dąbroś, Grzegorz Jaszczyk, Kostya Porotchkin,
Jici Gao, Rebecca Cran, kettenis
On Thu, 23 May 2019 at 19:02, Mark Kettenis <kettenis@jive.eu> wrote:
>
> > Date: Thu, 23 May 2019 15:14:27 +0100
> > From: Leif Lindholm <leif.lindholm@linaro.org>
> >
> > On Thu, May 23, 2019 at 03:27:47PM +0200, Mark Kettenis wrote:
> > > > From: Marcin Wojtas <mw@semihalf.com>
> > > > Date: Mon, 20 May 2019 17:27:13 +0200
> > > >
> > > > Hi,
> > > >
> > > > Thank you for thorough review of v1. I submit second
> > > > version of the Armada7k8k PCIE support. I addressed
> > > > all comments. There is no functional change to initial
> > > > patchset, but mostly clean-up and improvements - please
> > > > refer to the changelog below.
> > > >
> > > > The patches are available in the github:
> > > > https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/commits/pcie-upstream-r20190520
> > > >
> > > > I'm looking forward to your comments or remarks.
> > > >
> > > > Best regards,
> > > > Marcin
> > >
> > > Tested this on my mcbin running OpenBSD. It incovers a small issue in
> > > our kernel which I'm fixing. Otherwise this seems to work fine.
> > >
> > > So tested-by: Mark Kettenis <kettenis@openbsd.org> if that matters.
> >
> > Always helpful, thanks.
> >
> > Out of interest, what was the issue?
> > Could I still expect the 6.5 installer to run on this
> > hardware/firmware combo?
>
> That should still work fine.
>
> The issue is with mapping PCI ROMS, which currently fails with the new
> firmware due to an oversight in the OpenBSD code. There are only a
> few OpenBSD drivers that attempt to map the PCI ROM. But one of those
> is radeondrm(4) and I stuck an AMD graphics card into the PCIe slot on
> my machine.
>
> There is a bit of a firmware angle to this though. The issue happens
> because the PCI ROM address register has been set to 0xfffe0000. All
> the writable address bits in the register are set to 1. While it is
> possible that the hardware comes up in that state, I suspect this is
> done by an attempt by the firmware to determine the size of the ROM
> that doesn't properly restore the original contents of the register.
UEFI deliberately leaves the ROM BARs unassigned, in order to avoid
wasting valuable 32-bit PCI MMIO space. It enables the BAR temporarily
to load the ROM, and dispatches it if it can. After that, it changes
the BAR back to the old unassigned value.
> It may be related to the following messages that are printed by the
> firmware:
>
> Image type X64 can't be loaded on AARCH64 UEFI system.
> Unloading driver at 0x00000000000
That address value is quite unexpected.
> Connect: PcieRoot(0x0)/Pci(0x0,0x0): Not Found
>
> Hmm, that's actually interesting. Maybe I should play with the X86
> emulator that Ard added recently to see if that gives me a framebuffer
> console.
>
Yes, if you add edk2-staging to your PACKAGES_PATH env variable, all
you need to do is add -D X64EMU_ENABLE to the build command line.
If you do end up testing this, could you please report back with the
result, i.e., the type of card, PCI PID/VID and whether it all worked
as expected? Thanks.
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
2019-05-23 18:13 ` Ard Biesheuvel
@ 2019-05-23 20:11 ` Leif Lindholm
2019-05-23 20:24 ` Ard Biesheuvel
2019-05-24 22:16 ` mark.kettenis
1 sibling, 1 reply; 34+ messages in thread
From: Leif Lindholm @ 2019-05-23 20:11 UTC (permalink / raw)
To: Ard Biesheuvel
Cc: Mark Kettenis, Marcin Wojtas, edk2-devel-groups-io,
Jan Dąbroś, Grzegorz Jaszczyk, Kostya Porotchkin,
Jici Gao, Rebecca Cran, kettenis
On Thu, May 23, 2019 at 07:13:20PM +0100, Ard Biesheuvel wrote:
> > Connect: PcieRoot(0x0)/Pci(0x0,0x0): Not Found
> >
> > Hmm, that's actually interesting. Maybe I should play with the X86
> > emulator that Ard added recently to see if that gives me a framebuffer
> > console.
> >
>
> Yes, if you add edk2-staging to your PACKAGES_PATH env variable, all
> you need to do is add -D X64EMU_ENABLE to the build command line.
You mean edk2-non-osi, right?
/
Leif
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
2019-05-23 20:11 ` Leif Lindholm
@ 2019-05-23 20:24 ` Ard Biesheuvel
2019-05-24 13:08 ` Marcin Wojtas
0 siblings, 1 reply; 34+ messages in thread
From: Ard Biesheuvel @ 2019-05-23 20:24 UTC (permalink / raw)
To: Leif Lindholm
Cc: Mark Kettenis, Marcin Wojtas, edk2-devel-groups-io,
Jan Dąbroś, Grzegorz Jaszczyk, Kostya Porotchkin,
Jici Gao, Rebecca Cran, kettenis
On Thu, 23 May 2019 at 21:11, Leif Lindholm <leif.lindholm@linaro.org> wrote:
>
> On Thu, May 23, 2019 at 07:13:20PM +0100, Ard Biesheuvel wrote:
> > > Connect: PcieRoot(0x0)/Pci(0x0,0x0): Not Found
> > >
> > > Hmm, that's actually interesting. Maybe I should play with the X86
> > > emulator that Ard added recently to see if that gives me a framebuffer
> > > console.
> > >
> >
> > Yes, if you add edk2-staging to your PACKAGES_PATH env variable, all
> > you need to do is add -D X64EMU_ENABLE to the build command line.
>
> You mean edk2-non-osi, right?
>
Of course :-)
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation Marcin Wojtas
@ 2019-05-24 12:50 ` Ard Biesheuvel
2019-05-24 13:03 ` Marcin Wojtas
0 siblings, 1 reply; 34+ messages in thread
From: Ard Biesheuvel @ 2019-05-24 12:50 UTC (permalink / raw)
To: Marcin Wojtas
Cc: edk2-devel-groups-io, Leif Lindholm, Jan Dąbroś,
Grzegorz Jaszczyk, Kostya Porotchkin, Jici Gao, Rebecca Cran,
Mark Kettenis
On Mon, 20 May 2019 at 17:27, Marcin Wojtas <mw@semihalf.com> wrote:
>
> From: Ard Biesheuvel <ard.biesheuvel@linaro.org>
>
> Implement a special version of PciExpressLib that takes the quirky
> nature of the Synopsys Designware PCIe IP into account. In particular,
> we need to ignore config space accesses to all devices on the first
> bus except device 0, because the broadcast nature of type 0 configuration
> cycles will result in whatever device is in the slot to appear at each
> of the 32 device positions.
>
I never bothered to implement multisegment support for this SoC, since
MacchiatoBin has only one segment wired up, but since your interest is
in generic support, it might make sense to drop this patch and
implement PciSegmentLib instead (without depending on any of the other
library classes that the generic PciExpressLib depends on)
> Contributed-under: TianoCore Contribution Agreement 1.1
> Signed-off-by: Marcin Wojtas <mw@semihalf.com>
> ---
> Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf | 42 +
> Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c | 1531 ++++++++++++++++++++
> 2 files changed, 1573 insertions(+)
> create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
> create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
>
> diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
> new file mode 100644
> index 0000000..a66ef28
> --- /dev/null
> +++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
> @@ -0,0 +1,42 @@
> +## @file
> +#
> +# Copyright (c) 2017, Linaro, Ltd. All rights reserved.<BR>
> +# Copyright (c) 2019, Marvell International Ltd. All rights reserved.<BR>
> +#
> +# This program and the accompanying materials
> +# are licensed and made available under the terms and conditions of the BSD License
> +# which accompanies this distribution. The full text of the license may be found at
> +# http://opensource.org/licenses/bsd-license.php.
> +# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
> +# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
> +#
> +#
> +##
> +
> +[Defines]
> + INF_VERSION = 0x0001001B
> + BASE_NAME = Armada7k8kPciExpressLib
> + FILE_GUID = f0926204-3061-40ed-8261-2aeccc7914c9
> + MODULE_TYPE = BASE
> + VERSION_STRING = 1.0
> + LIBRARY_CLASS = PciExpressLib
> +
> +[Sources]
> + PciExpressLib.c
> +
> +[Packages]
> + ArmPkg/ArmPkg.dec
> + MdePkg/MdePkg.dec
> +
> +[LibraryClasses]
> + BaseLib
> + DebugLib
> + IoLib
> + PcdLib
> +
> +[Pcd]
> + gEfiMdePkgTokenSpaceGuid.PcdPciExpressBaseAddress ## CONSUMES
> +
> +[FixedPcd]
> + gArmTokenSpaceGuid.PcdPciBusMin
> + gArmTokenSpaceGuid.PcdPciBusMax
> diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
> new file mode 100644
> index 0000000..e88cc7b
> --- /dev/null
> +++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
> @@ -0,0 +1,1531 @@
> +/** @file
> +
> + Copyright (c) 2006 - 2012, Intel Corporation. All rights reserved.<BR>
> + Copyright (c) 2017, Linaro, Ltd. All rights reserved.<BR>
> + Copyright (c) 2019, Marvell International Ltd. All rights reserved.<BR>
> +
> + This program and the accompanying materials
> + are licensed and made available under the terms and conditions of the BSD License
> + which accompanies this distribution. The full text of the license may be found at
> + http://opensource.org/licenses/bsd-license.php.
> +
> + THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
> + WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
> +
> +**/
> +
> +
> +#include <Base.h>
> +
> +#include <Library/BaseLib.h>
> +#include <Library/DebugLib.h>
> +#include <Library/IoLib.h>
> +#include <Library/PcdLib.h>
> +#include <Library/PciExpressLib.h>
> +
> +/**
> + Assert the validity of a PCI address. A valid PCI address should contain 1's
> + only in the low 28 bits.
> +
> + @param A The address to validate.
> +
> +**/
> +#define ASSERT_INVALID_PCI_ADDRESS(A) \
> + ASSERT (((A) & ~0xfffffff) == 0)
> +
> +/**
> + Registers a PCI device so PCI configuration registers may be accessed after
> + SetVirtualAddressMap().
> +
> + Registers the PCI device specified by Address so all the PCI configuration
> + registers associated with that PCI device may be accessed after SetVirtualAddressMap()
> + is called.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> +
> + @retval RETURN_SUCCESS The PCI device was registered for runtime access.
> + @retval RETURN_UNSUPPORTED An attempt was made to call this function
> + after ExitBootServices().
> + @retval RETURN_UNSUPPORTED The resources required to access the PCI device
> + at runtime could not be mapped.
> + @retval RETURN_OUT_OF_RESOURCES There are not enough resources available to
> + complete the registration.
> +
> +**/
> +RETURN_STATUS
> +EFIAPI
> +PciExpressRegisterForRuntimeAccess (
> + IN UINTN Address
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + return RETURN_UNSUPPORTED;
> +}
> +
> +#define ECAM_BUS_SIZE SIZE_1MB
> +#define ECAM_DEV_SIZE SIZE_32KB
> +
> +STATIC
> +BOOLEAN
> +IgnoreBusDeviceFunction (
> + IN UINTN Address
> + )
> +{
> + ASSERT (Address >= FixedPcdGet32 (PcdPciBusMin) * ECAM_BUS_SIZE);
> + ASSERT (Address < (FixedPcdGet32 (PcdPciBusMax) + 1) * ECAM_BUS_SIZE);
> +
> + //
> + // Type 0 configuration cycles contain a b/d/f specifier, however
> + // the endpoint is unaware of its own device number and responds to all
> + // of them. The bus is responsible to ensure for assigning proper
> + // device/function. Sadly, the Synopsys IP does not implement this,
> + // and so we have to ignore config space accesses for all devices on the
> + // first bus except device 0.
> + //
> + return (Address >= (FixedPcdGet32 (PcdPciBusMin) * ECAM_BUS_SIZE +
> + ECAM_DEV_SIZE) &&
> + Address < (FixedPcdGet32 (PcdPciBusMin) + 1) * ECAM_BUS_SIZE);
> +}
> +
> +/**
> + Gets the base address of PCI Express.
> +
> + This internal functions retrieves PCI Express Base Address via a PCD entry
> + PcdPciExpressBaseAddress.
> +
> + @return The base address of PCI Express.
> +
> +**/
> +VOID *
> +GetPciExpressBaseAddress (
> + VOID
> + )
> +{
> + return (VOID *)(UINTN)PcdGet64 (PcdPciExpressBaseAddress);
> +}
> +
> +/**
> + Reads an 8-bit PCI configuration register.
> +
> + Reads and returns the 8-bit PCI configuration register specified by Address.
> + This function must guarantee that all PCI read and write operations are
> + serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> +
> + @return The read value from the PCI configuration register.
> +
> +**/
> +UINT8
> +EFIAPI
> +PciExpressRead8 (
> + IN UINTN Address
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT8;
> + }
> + return MmioRead8 ((UINTN)GetPciExpressBaseAddress () + Address);
> +}
> +
> +/**
> + Writes an 8-bit PCI configuration register.
> +
> + Writes the 8-bit PCI configuration register specified by Address with the
> + value specified by Value. Value is returned. This function must guarantee
> + that all PCI read and write operations are serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param Value The value to write.
> +
> + @return The value written to the PCI configuration register.
> +
> +**/
> +UINT8
> +EFIAPI
> +PciExpressWrite8 (
> + IN UINTN Address,
> + IN UINT8 Value
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT8;
> + }
> + return MmioWrite8 ((UINTN)GetPciExpressBaseAddress () + Address, Value);
> +}
> +
> +/**
> + Performs a bitwise OR of an 8-bit PCI configuration register with
> + an 8-bit value.
> +
> + Reads the 8-bit PCI configuration register specified by Address, performs a
> + bitwise OR between the read result and the value specified by
> + OrData, and writes the result to the 8-bit PCI configuration register
> + specified by Address. The value written to the PCI configuration register is
> + returned. This function must guarantee that all PCI read and write operations
> + are serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param OrData The value to OR with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT8
> +EFIAPI
> +PciExpressOr8 (
> + IN UINTN Address,
> + IN UINT8 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT8;
> + }
> + return MmioOr8 ((UINTN)GetPciExpressBaseAddress () + Address, OrData);
> +}
> +
> +/**
> + Performs a bitwise AND of an 8-bit PCI configuration register with an 8-bit
> + value.
> +
> + Reads the 8-bit PCI configuration register specified by Address, performs a
> + bitwise AND between the read result and the value specified by AndData, and
> + writes the result to the 8-bit PCI configuration register specified by
> + Address. The value written to the PCI configuration register is returned.
> + This function must guarantee that all PCI read and write operations are
> + serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param AndData The value to AND with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT8
> +EFIAPI
> +PciExpressAnd8 (
> + IN UINTN Address,
> + IN UINT8 AndData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT8;
> + }
> + return MmioAnd8 ((UINTN)GetPciExpressBaseAddress () + Address, AndData);
> +}
> +
> +/**
> + Performs a bitwise AND of an 8-bit PCI configuration register with an 8-bit
> + value, followed a bitwise OR with another 8-bit value.
> +
> + Reads the 8-bit PCI configuration register specified by Address, performs a
> + bitwise AND between the read result and the value specified by AndData,
> + performs a bitwise OR between the result of the AND operation and
> + the value specified by OrData, and writes the result to the 8-bit PCI
> + configuration register specified by Address. The value written to the PCI
> + configuration register is returned. This function must guarantee that all PCI
> + read and write operations are serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param AndData The value to AND with the PCI configuration register.
> + @param OrData The value to OR with the result of the AND operation.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT8
> +EFIAPI
> +PciExpressAndThenOr8 (
> + IN UINTN Address,
> + IN UINT8 AndData,
> + IN UINT8 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT8;
> + }
> + return MmioAndThenOr8 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + AndData,
> + OrData
> + );
> +}
> +
> +/**
> + Reads a bit field of a PCI configuration register.
> +
> + Reads the bit field in an 8-bit PCI configuration register. The bit field is
> + specified by the StartBit and the EndBit. The value of the bit field is
> + returned.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If StartBit is greater than 7, then ASSERT().
> + If EndBit is greater than 7, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> +
> + @param Address The PCI configuration register to read.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..7.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..7.
> +
> + @return The value of the bit field read from the PCI configuration register.
> +
> +**/
> +UINT8
> +EFIAPI
> +PciExpressBitFieldRead8 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT8;
> + }
> + return MmioBitFieldRead8 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit
> + );
> +}
> +
> +/**
> + Writes a bit field to a PCI configuration register.
> +
> + Writes Value to the bit field of the PCI configuration register. The bit
> + field is specified by the StartBit and the EndBit. All other bits in the
> + destination PCI configuration register are preserved. The new value of the
> + 8-bit register is returned.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If StartBit is greater than 7, then ASSERT().
> + If EndBit is greater than 7, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If Value is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..7.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..7.
> + @param Value The new value of the bit field.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT8
> +EFIAPI
> +PciExpressBitFieldWrite8 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT8 Value
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT8;
> + }
> + return MmioBitFieldWrite8 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + Value
> + );
> +}
> +
> +/**
> + Reads a bit field in an 8-bit PCI configuration, performs a bitwise OR, and
> + writes the result back to the bit field in the 8-bit port.
> +
> + Reads the 8-bit PCI configuration register specified by Address, performs a
> + bitwise OR between the read result and the value specified by
> + OrData, and writes the result to the 8-bit PCI configuration register
> + specified by Address. The value written to the PCI configuration register is
> + returned. This function must guarantee that all PCI read and write operations
> + are serialized. Extra left bits in OrData are stripped.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If StartBit is greater than 7, then ASSERT().
> + If EndBit is greater than 7, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..7.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..7.
> + @param OrData The value to OR with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT8
> +EFIAPI
> +PciExpressBitFieldOr8 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT8 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT8;
> + }
> + return MmioBitFieldOr8 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + OrData
> + );
> +}
> +
> +/**
> + Reads a bit field in an 8-bit PCI configuration register, performs a bitwise
> + AND, and writes the result back to the bit field in the 8-bit register.
> +
> + Reads the 8-bit PCI configuration register specified by Address, performs a
> + bitwise AND between the read result and the value specified by AndData, and
> + writes the result to the 8-bit PCI configuration register specified by
> + Address. The value written to the PCI configuration register is returned.
> + This function must guarantee that all PCI read and write operations are
> + serialized. Extra left bits in AndData are stripped.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If StartBit is greater than 7, then ASSERT().
> + If EndBit is greater than 7, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..7.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..7.
> + @param AndData The value to AND with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT8
> +EFIAPI
> +PciExpressBitFieldAnd8 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT8 AndData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT8;
> + }
> + return MmioBitFieldAnd8 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + AndData
> + );
> +}
> +
> +/**
> + Reads a bit field in an 8-bit port, performs a bitwise AND followed by a
> + bitwise OR, and writes the result back to the bit field in the
> + 8-bit port.
> +
> + Reads the 8-bit PCI configuration register specified by Address, performs a
> + bitwise AND followed by a bitwise OR between the read result and
> + the value specified by AndData, and writes the result to the 8-bit PCI
> + configuration register specified by Address. The value written to the PCI
> + configuration register is returned. This function must guarantee that all PCI
> + read and write operations are serialized. Extra left bits in both AndData and
> + OrData are stripped.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If StartBit is greater than 7, then ASSERT().
> + If EndBit is greater than 7, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..7.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..7.
> + @param AndData The value to AND with the PCI configuration register.
> + @param OrData The value to OR with the result of the AND operation.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT8
> +EFIAPI
> +PciExpressBitFieldAndThenOr8 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT8 AndData,
> + IN UINT8 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT8;
> + }
> + return MmioBitFieldAndThenOr8 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + AndData,
> + OrData
> + );
> +}
> +
> +/**
> + Reads a 16-bit PCI configuration register.
> +
> + Reads and returns the 16-bit PCI configuration register specified by Address.
> + This function must guarantee that all PCI read and write operations are
> + serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 16-bit boundary, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> +
> + @return The read value from the PCI configuration register.
> +
> +**/
> +UINT16
> +EFIAPI
> +PciExpressRead16 (
> + IN UINTN Address
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT16;
> + }
> + return MmioRead16 ((UINTN)GetPciExpressBaseAddress () + Address);
> +}
> +
> +/**
> + Writes a 16-bit PCI configuration register.
> +
> + Writes the 16-bit PCI configuration register specified by Address with the
> + value specified by Value. Value is returned. This function must guarantee
> + that all PCI read and write operations are serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 16-bit boundary, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param Value The value to write.
> +
> + @return The value written to the PCI configuration register.
> +
> +**/
> +UINT16
> +EFIAPI
> +PciExpressWrite16 (
> + IN UINTN Address,
> + IN UINT16 Value
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT16;
> + }
> + return MmioWrite16 ((UINTN)GetPciExpressBaseAddress () + Address, Value);
> +}
> +
> +/**
> + Performs a bitwise OR of a 16-bit PCI configuration register with
> + a 16-bit value.
> +
> + Reads the 16-bit PCI configuration register specified by Address, performs a
> + bitwise OR between the read result and the value specified by
> + OrData, and writes the result to the 16-bit PCI configuration register
> + specified by Address. The value written to the PCI configuration register is
> + returned. This function must guarantee that all PCI read and write operations
> + are serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 16-bit boundary, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param OrData The value to OR with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT16
> +EFIAPI
> +PciExpressOr16 (
> + IN UINTN Address,
> + IN UINT16 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT16;
> + }
> + return MmioOr16 ((UINTN)GetPciExpressBaseAddress () + Address, OrData);
> +}
> +
> +/**
> + Performs a bitwise AND of a 16-bit PCI configuration register with a 16-bit
> + value.
> +
> + Reads the 16-bit PCI configuration register specified by Address, performs a
> + bitwise AND between the read result and the value specified by AndData, and
> + writes the result to the 16-bit PCI configuration register specified by
> + Address. The value written to the PCI configuration register is returned.
> + This function must guarantee that all PCI read and write operations are
> + serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 16-bit boundary, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param AndData The value to AND with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT16
> +EFIAPI
> +PciExpressAnd16 (
> + IN UINTN Address,
> + IN UINT16 AndData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT16;
> + }
> + return MmioAnd16 ((UINTN)GetPciExpressBaseAddress () + Address, AndData);
> +}
> +
> +/**
> + Performs a bitwise AND of a 16-bit PCI configuration register with a 16-bit
> + value, followed a bitwise OR with another 16-bit value.
> +
> + Reads the 16-bit PCI configuration register specified by Address, performs a
> + bitwise AND between the read result and the value specified by AndData,
> + performs a bitwise OR between the result of the AND operation and
> + the value specified by OrData, and writes the result to the 16-bit PCI
> + configuration register specified by Address. The value written to the PCI
> + configuration register is returned. This function must guarantee that all PCI
> + read and write operations are serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 16-bit boundary, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param AndData The value to AND with the PCI configuration register.
> + @param OrData The value to OR with the result of the AND operation.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT16
> +EFIAPI
> +PciExpressAndThenOr16 (
> + IN UINTN Address,
> + IN UINT16 AndData,
> + IN UINT16 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT16;
> + }
> + return MmioAndThenOr16 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + AndData,
> + OrData
> + );
> +}
> +
> +/**
> + Reads a bit field of a PCI configuration register.
> +
> + Reads the bit field in a 16-bit PCI configuration register. The bit field is
> + specified by the StartBit and the EndBit. The value of the bit field is
> + returned.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 16-bit boundary, then ASSERT().
> + If StartBit is greater than 15, then ASSERT().
> + If EndBit is greater than 15, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> +
> + @param Address The PCI configuration register to read.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..15.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..15.
> +
> + @return The value of the bit field read from the PCI configuration register.
> +
> +**/
> +UINT16
> +EFIAPI
> +PciExpressBitFieldRead16 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT16;
> + }
> + return MmioBitFieldRead16 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit
> + );
> +}
> +
> +/**
> + Writes a bit field to a PCI configuration register.
> +
> + Writes Value to the bit field of the PCI configuration register. The bit
> + field is specified by the StartBit and the EndBit. All other bits in the
> + destination PCI configuration register are preserved. The new value of the
> + 16-bit register is returned.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 16-bit boundary, then ASSERT().
> + If StartBit is greater than 15, then ASSERT().
> + If EndBit is greater than 15, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If Value is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..15.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..15.
> + @param Value The new value of the bit field.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT16
> +EFIAPI
> +PciExpressBitFieldWrite16 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT16 Value
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT16;
> + }
> + return MmioBitFieldWrite16 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + Value
> + );
> +}
> +
> +/**
> + Reads a bit field in a 16-bit PCI configuration, performs a bitwise OR, and
> + writes the result back to the bit field in the 16-bit port.
> +
> + Reads the 16-bit PCI configuration register specified by Address, performs a
> + bitwise OR between the read result and the value specified by
> + OrData, and writes the result to the 16-bit PCI configuration register
> + specified by Address. The value written to the PCI configuration register is
> + returned. This function must guarantee that all PCI read and write operations
> + are serialized. Extra left bits in OrData are stripped.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 16-bit boundary, then ASSERT().
> + If StartBit is greater than 15, then ASSERT().
> + If EndBit is greater than 15, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..15.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..15.
> + @param OrData The value to OR with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT16
> +EFIAPI
> +PciExpressBitFieldOr16 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT16 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT16;
> + }
> + return MmioBitFieldOr16 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + OrData
> + );
> +}
> +
> +/**
> + Reads a bit field in a 16-bit PCI configuration register, performs a bitwise
> + AND, and writes the result back to the bit field in the 16-bit register.
> +
> + Reads the 16-bit PCI configuration register specified by Address, performs a
> + bitwise AND between the read result and the value specified by AndData, and
> + writes the result to the 16-bit PCI configuration register specified by
> + Address. The value written to the PCI configuration register is returned.
> + This function must guarantee that all PCI read and write operations are
> + serialized. Extra left bits in AndData are stripped.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 16-bit boundary, then ASSERT().
> + If StartBit is greater than 15, then ASSERT().
> + If EndBit is greater than 15, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..15.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..15.
> + @param AndData The value to AND with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT16
> +EFIAPI
> +PciExpressBitFieldAnd16 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT16 AndData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT16;
> + }
> + return MmioBitFieldAnd16 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + AndData
> + );
> +}
> +
> +/**
> + Reads a bit field in a 16-bit port, performs a bitwise AND followed by a
> + bitwise OR, and writes the result back to the bit field in the
> + 16-bit port.
> +
> + Reads the 16-bit PCI configuration register specified by Address, performs a
> + bitwise AND followed by a bitwise OR between the read result and
> + the value specified by AndData, and writes the result to the 16-bit PCI
> + configuration register specified by Address. The value written to the PCI
> + configuration register is returned. This function must guarantee that all PCI
> + read and write operations are serialized. Extra left bits in both AndData and
> + OrData are stripped.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 16-bit boundary, then ASSERT().
> + If StartBit is greater than 15, then ASSERT().
> + If EndBit is greater than 15, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..15.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..15.
> + @param AndData The value to AND with the PCI configuration register.
> + @param OrData The value to OR with the result of the AND operation.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT16
> +EFIAPI
> +PciExpressBitFieldAndThenOr16 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT16 AndData,
> + IN UINT16 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT16;
> + }
> + return MmioBitFieldAndThenOr16 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + AndData,
> + OrData
> + );
> +}
> +
> +/**
> + Reads a 32-bit PCI configuration register.
> +
> + Reads and returns the 32-bit PCI configuration register specified by Address.
> + This function must guarantee that all PCI read and write operations are
> + serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 32-bit boundary, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> +
> + @return The read value from the PCI configuration register.
> +
> +**/
> +UINT32
> +EFIAPI
> +PciExpressRead32 (
> + IN UINTN Address
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT32;
> + }
> + return MmioRead32 ((UINTN)GetPciExpressBaseAddress () + Address);
> +}
> +
> +/**
> + Writes a 32-bit PCI configuration register.
> +
> + Writes the 32-bit PCI configuration register specified by Address with the
> + value specified by Value. Value is returned. This function must guarantee
> + that all PCI read and write operations are serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 32-bit boundary, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param Value The value to write.
> +
> + @return The value written to the PCI configuration register.
> +
> +**/
> +UINT32
> +EFIAPI
> +PciExpressWrite32 (
> + IN UINTN Address,
> + IN UINT32 Value
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT32;
> + }
> + return MmioWrite32 ((UINTN)GetPciExpressBaseAddress () + Address, Value);
> +}
> +
> +/**
> + Performs a bitwise OR of a 32-bit PCI configuration register with
> + a 32-bit value.
> +
> + Reads the 32-bit PCI configuration register specified by Address, performs a
> + bitwise OR between the read result and the value specified by
> + OrData, and writes the result to the 32-bit PCI configuration register
> + specified by Address. The value written to the PCI configuration register is
> + returned. This function must guarantee that all PCI read and write operations
> + are serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 32-bit boundary, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param OrData The value to OR with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT32
> +EFIAPI
> +PciExpressOr32 (
> + IN UINTN Address,
> + IN UINT32 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT32;
> + }
> + return MmioOr32 ((UINTN)GetPciExpressBaseAddress () + Address, OrData);
> +}
> +
> +/**
> + Performs a bitwise AND of a 32-bit PCI configuration register with a 32-bit
> + value.
> +
> + Reads the 32-bit PCI configuration register specified by Address, performs a
> + bitwise AND between the read result and the value specified by AndData, and
> + writes the result to the 32-bit PCI configuration register specified by
> + Address. The value written to the PCI configuration register is returned.
> + This function must guarantee that all PCI read and write operations are
> + serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 32-bit boundary, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param AndData The value to AND with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT32
> +EFIAPI
> +PciExpressAnd32 (
> + IN UINTN Address,
> + IN UINT32 AndData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT32;
> + }
> +return MmioAnd32 ((UINTN)GetPciExpressBaseAddress () + Address, AndData);
> +}
> +
> +/**
> + Performs a bitwise AND of a 32-bit PCI configuration register with a 32-bit
> + value, followed a bitwise OR with another 32-bit value.
> +
> + Reads the 32-bit PCI configuration register specified by Address, performs a
> + bitwise AND between the read result and the value specified by AndData,
> + performs a bitwise OR between the result of the AND operation and
> + the value specified by OrData, and writes the result to the 32-bit PCI
> + configuration register specified by Address. The value written to the PCI
> + configuration register is returned. This function must guarantee that all PCI
> + read and write operations are serialized.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 32-bit boundary, then ASSERT().
> +
> + @param Address The address that encodes the PCI Bus, Device, Function and
> + Register.
> + @param AndData The value to AND with the PCI configuration register.
> + @param OrData The value to OR with the result of the AND operation.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT32
> +EFIAPI
> +PciExpressAndThenOr32 (
> + IN UINTN Address,
> + IN UINT32 AndData,
> + IN UINT32 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT32;
> + }
> + return MmioAndThenOr32 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + AndData,
> + OrData
> + );
> +}
> +
> +/**
> + Reads a bit field of a PCI configuration register.
> +
> + Reads the bit field in a 32-bit PCI configuration register. The bit field is
> + specified by the StartBit and the EndBit. The value of the bit field is
> + returned.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 32-bit boundary, then ASSERT().
> + If StartBit is greater than 31, then ASSERT().
> + If EndBit is greater than 31, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> +
> + @param Address The PCI configuration register to read.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..31.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..31.
> +
> + @return The value of the bit field read from the PCI configuration register.
> +
> +**/
> +UINT32
> +EFIAPI
> +PciExpressBitFieldRead32 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT32;
> + }
> + return MmioBitFieldRead32 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit
> + );
> +}
> +
> +/**
> + Writes a bit field to a PCI configuration register.
> +
> + Writes Value to the bit field of the PCI configuration register. The bit
> + field is specified by the StartBit and the EndBit. All other bits in the
> + destination PCI configuration register are preserved. The new value of the
> + 32-bit register is returned.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 32-bit boundary, then ASSERT().
> + If StartBit is greater than 31, then ASSERT().
> + If EndBit is greater than 31, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If Value is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..31.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..31.
> + @param Value The new value of the bit field.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT32
> +EFIAPI
> +PciExpressBitFieldWrite32 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT32 Value
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT32;
> + }
> + return MmioBitFieldWrite32 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + Value
> + );
> +}
> +
> +/**
> + Reads a bit field in a 32-bit PCI configuration, performs a bitwise OR, and
> + writes the result back to the bit field in the 32-bit port.
> +
> + Reads the 32-bit PCI configuration register specified by Address, performs a
> + bitwise OR between the read result and the value specified by
> + OrData, and writes the result to the 32-bit PCI configuration register
> + specified by Address. The value written to the PCI configuration register is
> + returned. This function must guarantee that all PCI read and write operations
> + are serialized. Extra left bits in OrData are stripped.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 32-bit boundary, then ASSERT().
> + If StartBit is greater than 31, then ASSERT().
> + If EndBit is greater than 31, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..31.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..31.
> + @param OrData The value to OR with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT32
> +EFIAPI
> +PciExpressBitFieldOr32 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT32 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT32;
> + }
> + return MmioBitFieldOr32 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + OrData
> + );
> +}
> +
> +/**
> + Reads a bit field in a 32-bit PCI configuration register, performs a bitwise
> + AND, and writes the result back to the bit field in the 32-bit register.
> +
> + Reads the 32-bit PCI configuration register specified by Address, performs a
> + bitwise AND between the read result and the value specified by AndData, and
> + writes the result to the 32-bit PCI configuration register specified by
> + Address. The value written to the PCI configuration register is returned.
> + This function must guarantee that all PCI read and write operations are
> + serialized. Extra left bits in AndData are stripped.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 32-bit boundary, then ASSERT().
> + If StartBit is greater than 31, then ASSERT().
> + If EndBit is greater than 31, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..31.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..31.
> + @param AndData The value to AND with the PCI configuration register.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT32
> +EFIAPI
> +PciExpressBitFieldAnd32 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT32 AndData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT32;
> + }
> + return MmioBitFieldAnd32 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + AndData
> + );
> +}
> +
> +/**
> + Reads a bit field in a 32-bit port, performs a bitwise AND followed by a
> + bitwise OR, and writes the result back to the bit field in the
> + 32-bit port.
> +
> + Reads the 32-bit PCI configuration register specified by Address, performs a
> + bitwise AND followed by a bitwise OR between the read result and
> + the value specified by AndData, and writes the result to the 32-bit PCI
> + configuration register specified by Address. The value written to the PCI
> + configuration register is returned. This function must guarantee that all PCI
> + read and write operations are serialized. Extra left bits in both AndData and
> + OrData are stripped.
> +
> + If Address > 0x0FFFFFFF, then ASSERT().
> + If Address is not aligned on a 32-bit boundary, then ASSERT().
> + If StartBit is greater than 31, then ASSERT().
> + If EndBit is greater than 31, then ASSERT().
> + If EndBit is less than StartBit, then ASSERT().
> + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> +
> + @param Address The PCI configuration register to write.
> + @param StartBit The ordinal of the least significant bit in the bit field.
> + Range 0..31.
> + @param EndBit The ordinal of the most significant bit in the bit field.
> + Range 0..31.
> + @param AndData The value to AND with the PCI configuration register.
> + @param OrData The value to OR with the result of the AND operation.
> +
> + @return The value written back to the PCI configuration register.
> +
> +**/
> +UINT32
> +EFIAPI
> +PciExpressBitFieldAndThenOr32 (
> + IN UINTN Address,
> + IN UINTN StartBit,
> + IN UINTN EndBit,
> + IN UINT32 AndData,
> + IN UINT32 OrData
> + )
> +{
> + ASSERT_INVALID_PCI_ADDRESS (Address);
> + if (IgnoreBusDeviceFunction (Address)) {
> + return MAX_UINT32;
> + }
> + return MmioBitFieldAndThenOr32 (
> + (UINTN)GetPciExpressBaseAddress () + Address,
> + StartBit,
> + EndBit,
> + AndData,
> + OrData
> + );
> +}
> +
> +/**
> + Reads a range of PCI configuration registers into a caller supplied buffer.
> +
> + Reads the range of PCI configuration registers specified by StartAddress and
> + Size into the buffer specified by Buffer. This function only allows the PCI
> + configuration registers from a single PCI function to be read. Size is
> + returned. When possible 32-bit PCI configuration read cycles are used to read
> + from StartAddress to StartAddress + Size. Due to alignment restrictions, 8-bit
> + and 16-bit PCI configuration read cycles may be used at the beginning and the
> + end of the range.
> +
> + If StartAddress > 0x0FFFFFFF, then ASSERT().
> + If ((StartAddress & 0xFFF) + Size) > 0x1000, then ASSERT().
> + If Size > 0 and Buffer is NULL, then ASSERT().
> +
> + @param StartAddress The starting address that encodes the PCI Bus, Device,
> + Function and Register.
> + @param Size The size in bytes of the transfer.
> + @param Buffer The pointer to a buffer receiving the data read.
> +
> + @return Size read data from StartAddress.
> +
> +**/
> +UINTN
> +EFIAPI
> +PciExpressReadBuffer (
> + IN UINTN StartAddress,
> + IN UINTN Size,
> + OUT VOID *Buffer
> + )
> +{
> + UINTN ReturnValue;
> +
> + ASSERT_INVALID_PCI_ADDRESS (StartAddress);
> + ASSERT (((StartAddress & 0xFFF) + Size) <= 0x1000);
> +
> + if (Size == 0) {
> + return Size;
> + }
> +
> + ASSERT (Buffer != NULL);
> +
> + //
> + // Save Size for return
> + //
> + ReturnValue = Size;
> +
> + if ((StartAddress & 1) != 0) {
> + //
> + // Read a byte if StartAddress is byte aligned
> + //
> + MmioWrite8 ((UINTN)Buffer, PciExpressRead8 (StartAddress));
> + StartAddress += sizeof (UINT8);
> + Size -= sizeof (UINT8);
> + Buffer = (UINT8 *)Buffer + 1;
> + }
> +
> + if (Size >= sizeof (UINT16)&& (StartAddress & 2) != 0) {
> + //
> + // Read a word if StartAddress is word aligned
> + //
> + WriteUnaligned16 ((UINT16 *)Buffer, (UINT16)PciExpressRead16 (StartAddress));
> +
> + StartAddress += sizeof (UINT16);
> + Size -= sizeof (UINT16);
> + Buffer = (UINT16 *)Buffer + 1;
> + }
> +
> + while (Size >= sizeof (UINT32)) {
> + //
> + // Read as many double words as possible
> + //
> + WriteUnaligned32 ((UINT32 *)Buffer, (UINT32)PciExpressRead32 (StartAddress));
> +
> + StartAddress += sizeof (UINT32);
> + Size -= sizeof (UINT32);
> + Buffer = (UINT32 *)Buffer + 1;
> + }
> +
> + if (Size >= sizeof (UINT16)) {
> + //
> + // Read the last remaining word if exist
> + //
> + WriteUnaligned16 ((UINT16 *)Buffer, (UINT16)PciExpressRead16 (StartAddress));
> + StartAddress += sizeof (UINT16);
> + Size -= sizeof (UINT16);
> + Buffer = (UINT16 *)Buffer + 1;
> + }
> +
> + if (Size >= sizeof (UINT8)) {
> + //
> + // Read the last remaining byte if exist
> + //
> + MmioWrite8 ((UINTN)Buffer, PciExpressRead8 (StartAddress));
> + }
> +
> + return ReturnValue;
> +}
> +
> +/**
> + Copies the data in a caller supplied buffer to a specified range of PCI
> + configuration space.
> +
> + Writes the range of PCI configuration registers specified by StartAddress and
> + Size from the buffer specified by Buffer. This function only allows the PCI
> + configuration registers from a single PCI function to be written. Size is
> + returned. When possible 32-bit PCI configuration write cycles are used to
> + write from StartAddress to StartAddress + Size. Due to alignment restrictions,
> + 8-bit and 16-bit PCI configuration write cycles may be used at the beginning
> + and the end of the range.
> +
> + If StartAddress > 0x0FFFFFFF, then ASSERT().
> + If ((StartAddress & 0xFFF) + Size) > 0x1000, then ASSERT().
> + If Size > 0 and Buffer is NULL, then ASSERT().
> +
> + @param StartAddress The starting address that encodes the PCI Bus, Device,
> + Function and Register.
> + @param Size The size in bytes of the transfer.
> + @param Buffer The pointer to a buffer containing the data to write.
> +
> + @return Size written to StartAddress.
> +
> +**/
> +UINTN
> +EFIAPI
> +PciExpressWriteBuffer (
> + IN UINTN StartAddress,
> + IN UINTN Size,
> + IN VOID *Buffer
> + )
> +{
> + UINTN ReturnValue;
> +
> + ASSERT_INVALID_PCI_ADDRESS (StartAddress);
> + ASSERT (((StartAddress & 0xFFF) + Size) <= 0x1000);
> +
> + if (Size == 0) {
> + return 0;
> + }
> +
> + ASSERT (Buffer != NULL);
> +
> + //
> + // Save Size for return
> + //
> + ReturnValue = Size;
> +
> + if ((StartAddress & 1) != 0) {
> + //
> + // Write a byte if StartAddress is byte aligned
> + //
> + PciExpressWrite8 (StartAddress, *(UINT8 *)Buffer);
> + StartAddress += sizeof (UINT8);
> + Size -= sizeof (UINT8);
> + Buffer = (UINT8 *)Buffer + 1;
> + }
> +
> + if (Size >= sizeof (UINT16) && (StartAddress & 2) != 0) {
> + //
> + // Write a word if StartAddress is word aligned
> + //
> + PciExpressWrite16 (StartAddress, ReadUnaligned16 ((UINT16 *)Buffer));
> + StartAddress += sizeof (UINT16);
> + Size -= sizeof (UINT16);
> + Buffer = (UINT16 *)Buffer + 1;
> + }
> +
> + while (Size >= sizeof (UINT32)) {
> + //
> + // Write as many double words as possible
> + //
> + PciExpressWrite32 (StartAddress, ReadUnaligned32 ((UINT32 *)Buffer));
> + StartAddress += sizeof (UINT32);
> + Size -= sizeof (UINT32);
> + Buffer = (UINT32 *)Buffer + 1;
> + }
> +
> + if (Size >= sizeof (UINT16)) {
> + //
> + // Write the last remaining word if exist
> + //
> + PciExpressWrite16 (StartAddress, ReadUnaligned16 ((UINT16 *)Buffer));
> + StartAddress += sizeof (UINT16);
> + Size -= sizeof (UINT16);
> + Buffer = (UINT16 *)Buffer + 1;
> + }
> +
> + if (Size >= sizeof (UINT8)) {
> + //
> + // Write the last remaining byte if exist
> + //
> + PciExpressWrite8 (StartAddress, *(UINT8 *)Buffer);
> + }
> +
> + return ReturnValue;
> +}
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation
2019-05-24 12:50 ` Ard Biesheuvel
@ 2019-05-24 13:03 ` Marcin Wojtas
2019-05-24 13:08 ` Ard Biesheuvel
0 siblings, 1 reply; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-24 13:03 UTC (permalink / raw)
To: Ard Biesheuvel
Cc: edk2-devel-groups-io, Leif Lindholm, Jan Dąbroś,
Grzegorz Jaszczyk, Kostya Porotchkin, Jici Gao, Rebecca Cran,
Mark Kettenis
pt., 24 maj 2019 o 14:50 Ard Biesheuvel <ard.biesheuvel@linaro.org> napisał(a):
>
> On Mon, 20 May 2019 at 17:27, Marcin Wojtas <mw@semihalf.com> wrote:
> >
> > From: Ard Biesheuvel <ard.biesheuvel@linaro.org>
> >
> > Implement a special version of PciExpressLib that takes the quirky
> > nature of the Synopsys Designware PCIe IP into account. In particular,
> > we need to ignore config space accesses to all devices on the first
> > bus except device 0, because the broadcast nature of type 0 configuration
> > cycles will result in whatever device is in the slot to appear at each
> > of the 32 device positions.
> >
>
> I never bothered to implement multisegment support for this SoC, since
> MacchiatoBin has only one segment wired up, but since your interest is
> in generic support, it might make sense to drop this patch and
> implement PciSegmentLib instead (without depending on any of the other
> library classes that the generic PciExpressLib depends on)
>
This was (and still is) my plan, but I've been having some serious
time shortages for extra development. In order not to postpone this
support any longer I prefer to get merged, what I have and possibly
rework on top.
About depending on a generic PciExpressLib - do you mean I can filter
out devices from bus0 in PciSegmentLib?
Thanks,
Marcin
>
> > Contributed-under: TianoCore Contribution Agreement 1.1
> > Signed-off-by: Marcin Wojtas <mw@semihalf.com>
> > ---
> > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf | 42 +
> > Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c | 1531 ++++++++++++++++++++
> > 2 files changed, 1573 insertions(+)
> > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
> > create mode 100644 Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
> >
> > diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
> > new file mode 100644
> > index 0000000..a66ef28
> > --- /dev/null
> > +++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.inf
> > @@ -0,0 +1,42 @@
> > +## @file
> > +#
> > +# Copyright (c) 2017, Linaro, Ltd. All rights reserved.<BR>
> > +# Copyright (c) 2019, Marvell International Ltd. All rights reserved.<BR>
> > +#
> > +# This program and the accompanying materials
> > +# are licensed and made available under the terms and conditions of the BSD License
> > +# which accompanies this distribution. The full text of the license may be found at
> > +# http://opensource.org/licenses/bsd-license.php.
> > +# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
> > +# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
> > +#
> > +#
> > +##
> > +
> > +[Defines]
> > + INF_VERSION = 0x0001001B
> > + BASE_NAME = Armada7k8kPciExpressLib
> > + FILE_GUID = f0926204-3061-40ed-8261-2aeccc7914c9
> > + MODULE_TYPE = BASE
> > + VERSION_STRING = 1.0
> > + LIBRARY_CLASS = PciExpressLib
> > +
> > +[Sources]
> > + PciExpressLib.c
> > +
> > +[Packages]
> > + ArmPkg/ArmPkg.dec
> > + MdePkg/MdePkg.dec
> > +
> > +[LibraryClasses]
> > + BaseLib
> > + DebugLib
> > + IoLib
> > + PcdLib
> > +
> > +[Pcd]
> > + gEfiMdePkgTokenSpaceGuid.PcdPciExpressBaseAddress ## CONSUMES
> > +
> > +[FixedPcd]
> > + gArmTokenSpaceGuid.PcdPciBusMin
> > + gArmTokenSpaceGuid.PcdPciBusMax
> > diff --git a/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
> > new file mode 100644
> > index 0000000..e88cc7b
> > --- /dev/null
> > +++ b/Silicon/Marvell/Armada7k8k/Library/Armada7k8kPciExpressLib/PciExpressLib.c
> > @@ -0,0 +1,1531 @@
> > +/** @file
> > +
> > + Copyright (c) 2006 - 2012, Intel Corporation. All rights reserved.<BR>
> > + Copyright (c) 2017, Linaro, Ltd. All rights reserved.<BR>
> > + Copyright (c) 2019, Marvell International Ltd. All rights reserved.<BR>
> > +
> > + This program and the accompanying materials
> > + are licensed and made available under the terms and conditions of the BSD License
> > + which accompanies this distribution. The full text of the license may be found at
> > + http://opensource.org/licenses/bsd-license.php.
> > +
> > + THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
> > + WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
> > +
> > +**/
> > +
> > +
> > +#include <Base.h>
> > +
> > +#include <Library/BaseLib.h>
> > +#include <Library/DebugLib.h>
> > +#include <Library/IoLib.h>
> > +#include <Library/PcdLib.h>
> > +#include <Library/PciExpressLib.h>
> > +
> > +/**
> > + Assert the validity of a PCI address. A valid PCI address should contain 1's
> > + only in the low 28 bits.
> > +
> > + @param A The address to validate.
> > +
> > +**/
> > +#define ASSERT_INVALID_PCI_ADDRESS(A) \
> > + ASSERT (((A) & ~0xfffffff) == 0)
> > +
> > +/**
> > + Registers a PCI device so PCI configuration registers may be accessed after
> > + SetVirtualAddressMap().
> > +
> > + Registers the PCI device specified by Address so all the PCI configuration
> > + registers associated with that PCI device may be accessed after SetVirtualAddressMap()
> > + is called.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > +
> > + @retval RETURN_SUCCESS The PCI device was registered for runtime access.
> > + @retval RETURN_UNSUPPORTED An attempt was made to call this function
> > + after ExitBootServices().
> > + @retval RETURN_UNSUPPORTED The resources required to access the PCI device
> > + at runtime could not be mapped.
> > + @retval RETURN_OUT_OF_RESOURCES There are not enough resources available to
> > + complete the registration.
> > +
> > +**/
> > +RETURN_STATUS
> > +EFIAPI
> > +PciExpressRegisterForRuntimeAccess (
> > + IN UINTN Address
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + return RETURN_UNSUPPORTED;
> > +}
> > +
> > +#define ECAM_BUS_SIZE SIZE_1MB
> > +#define ECAM_DEV_SIZE SIZE_32KB
> > +
> > +STATIC
> > +BOOLEAN
> > +IgnoreBusDeviceFunction (
> > + IN UINTN Address
> > + )
> > +{
> > + ASSERT (Address >= FixedPcdGet32 (PcdPciBusMin) * ECAM_BUS_SIZE);
> > + ASSERT (Address < (FixedPcdGet32 (PcdPciBusMax) + 1) * ECAM_BUS_SIZE);
> > +
> > + //
> > + // Type 0 configuration cycles contain a b/d/f specifier, however
> > + // the endpoint is unaware of its own device number and responds to all
> > + // of them. The bus is responsible to ensure for assigning proper
> > + // device/function. Sadly, the Synopsys IP does not implement this,
> > + // and so we have to ignore config space accesses for all devices on the
> > + // first bus except device 0.
> > + //
> > + return (Address >= (FixedPcdGet32 (PcdPciBusMin) * ECAM_BUS_SIZE +
> > + ECAM_DEV_SIZE) &&
> > + Address < (FixedPcdGet32 (PcdPciBusMin) + 1) * ECAM_BUS_SIZE);
> > +}
> > +
> > +/**
> > + Gets the base address of PCI Express.
> > +
> > + This internal functions retrieves PCI Express Base Address via a PCD entry
> > + PcdPciExpressBaseAddress.
> > +
> > + @return The base address of PCI Express.
> > +
> > +**/
> > +VOID *
> > +GetPciExpressBaseAddress (
> > + VOID
> > + )
> > +{
> > + return (VOID *)(UINTN)PcdGet64 (PcdPciExpressBaseAddress);
> > +}
> > +
> > +/**
> > + Reads an 8-bit PCI configuration register.
> > +
> > + Reads and returns the 8-bit PCI configuration register specified by Address.
> > + This function must guarantee that all PCI read and write operations are
> > + serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > +
> > + @return The read value from the PCI configuration register.
> > +
> > +**/
> > +UINT8
> > +EFIAPI
> > +PciExpressRead8 (
> > + IN UINTN Address
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT8;
> > + }
> > + return MmioRead8 ((UINTN)GetPciExpressBaseAddress () + Address);
> > +}
> > +
> > +/**
> > + Writes an 8-bit PCI configuration register.
> > +
> > + Writes the 8-bit PCI configuration register specified by Address with the
> > + value specified by Value. Value is returned. This function must guarantee
> > + that all PCI read and write operations are serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param Value The value to write.
> > +
> > + @return The value written to the PCI configuration register.
> > +
> > +**/
> > +UINT8
> > +EFIAPI
> > +PciExpressWrite8 (
> > + IN UINTN Address,
> > + IN UINT8 Value
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT8;
> > + }
> > + return MmioWrite8 ((UINTN)GetPciExpressBaseAddress () + Address, Value);
> > +}
> > +
> > +/**
> > + Performs a bitwise OR of an 8-bit PCI configuration register with
> > + an 8-bit value.
> > +
> > + Reads the 8-bit PCI configuration register specified by Address, performs a
> > + bitwise OR between the read result and the value specified by
> > + OrData, and writes the result to the 8-bit PCI configuration register
> > + specified by Address. The value written to the PCI configuration register is
> > + returned. This function must guarantee that all PCI read and write operations
> > + are serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param OrData The value to OR with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT8
> > +EFIAPI
> > +PciExpressOr8 (
> > + IN UINTN Address,
> > + IN UINT8 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT8;
> > + }
> > + return MmioOr8 ((UINTN)GetPciExpressBaseAddress () + Address, OrData);
> > +}
> > +
> > +/**
> > + Performs a bitwise AND of an 8-bit PCI configuration register with an 8-bit
> > + value.
> > +
> > + Reads the 8-bit PCI configuration register specified by Address, performs a
> > + bitwise AND between the read result and the value specified by AndData, and
> > + writes the result to the 8-bit PCI configuration register specified by
> > + Address. The value written to the PCI configuration register is returned.
> > + This function must guarantee that all PCI read and write operations are
> > + serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param AndData The value to AND with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT8
> > +EFIAPI
> > +PciExpressAnd8 (
> > + IN UINTN Address,
> > + IN UINT8 AndData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT8;
> > + }
> > + return MmioAnd8 ((UINTN)GetPciExpressBaseAddress () + Address, AndData);
> > +}
> > +
> > +/**
> > + Performs a bitwise AND of an 8-bit PCI configuration register with an 8-bit
> > + value, followed a bitwise OR with another 8-bit value.
> > +
> > + Reads the 8-bit PCI configuration register specified by Address, performs a
> > + bitwise AND between the read result and the value specified by AndData,
> > + performs a bitwise OR between the result of the AND operation and
> > + the value specified by OrData, and writes the result to the 8-bit PCI
> > + configuration register specified by Address. The value written to the PCI
> > + configuration register is returned. This function must guarantee that all PCI
> > + read and write operations are serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param AndData The value to AND with the PCI configuration register.
> > + @param OrData The value to OR with the result of the AND operation.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT8
> > +EFIAPI
> > +PciExpressAndThenOr8 (
> > + IN UINTN Address,
> > + IN UINT8 AndData,
> > + IN UINT8 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT8;
> > + }
> > + return MmioAndThenOr8 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + AndData,
> > + OrData
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field of a PCI configuration register.
> > +
> > + Reads the bit field in an 8-bit PCI configuration register. The bit field is
> > + specified by the StartBit and the EndBit. The value of the bit field is
> > + returned.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If StartBit is greater than 7, then ASSERT().
> > + If EndBit is greater than 7, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to read.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..7.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..7.
> > +
> > + @return The value of the bit field read from the PCI configuration register.
> > +
> > +**/
> > +UINT8
> > +EFIAPI
> > +PciExpressBitFieldRead8 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT8;
> > + }
> > + return MmioBitFieldRead8 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit
> > + );
> > +}
> > +
> > +/**
> > + Writes a bit field to a PCI configuration register.
> > +
> > + Writes Value to the bit field of the PCI configuration register. The bit
> > + field is specified by the StartBit and the EndBit. All other bits in the
> > + destination PCI configuration register are preserved. The new value of the
> > + 8-bit register is returned.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If StartBit is greater than 7, then ASSERT().
> > + If EndBit is greater than 7, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If Value is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..7.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..7.
> > + @param Value The new value of the bit field.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT8
> > +EFIAPI
> > +PciExpressBitFieldWrite8 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT8 Value
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT8;
> > + }
> > + return MmioBitFieldWrite8 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + Value
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field in an 8-bit PCI configuration, performs a bitwise OR, and
> > + writes the result back to the bit field in the 8-bit port.
> > +
> > + Reads the 8-bit PCI configuration register specified by Address, performs a
> > + bitwise OR between the read result and the value specified by
> > + OrData, and writes the result to the 8-bit PCI configuration register
> > + specified by Address. The value written to the PCI configuration register is
> > + returned. This function must guarantee that all PCI read and write operations
> > + are serialized. Extra left bits in OrData are stripped.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If StartBit is greater than 7, then ASSERT().
> > + If EndBit is greater than 7, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..7.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..7.
> > + @param OrData The value to OR with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT8
> > +EFIAPI
> > +PciExpressBitFieldOr8 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT8 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT8;
> > + }
> > + return MmioBitFieldOr8 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + OrData
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field in an 8-bit PCI configuration register, performs a bitwise
> > + AND, and writes the result back to the bit field in the 8-bit register.
> > +
> > + Reads the 8-bit PCI configuration register specified by Address, performs a
> > + bitwise AND between the read result and the value specified by AndData, and
> > + writes the result to the 8-bit PCI configuration register specified by
> > + Address. The value written to the PCI configuration register is returned.
> > + This function must guarantee that all PCI read and write operations are
> > + serialized. Extra left bits in AndData are stripped.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If StartBit is greater than 7, then ASSERT().
> > + If EndBit is greater than 7, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..7.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..7.
> > + @param AndData The value to AND with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT8
> > +EFIAPI
> > +PciExpressBitFieldAnd8 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT8 AndData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT8;
> > + }
> > + return MmioBitFieldAnd8 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + AndData
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field in an 8-bit port, performs a bitwise AND followed by a
> > + bitwise OR, and writes the result back to the bit field in the
> > + 8-bit port.
> > +
> > + Reads the 8-bit PCI configuration register specified by Address, performs a
> > + bitwise AND followed by a bitwise OR between the read result and
> > + the value specified by AndData, and writes the result to the 8-bit PCI
> > + configuration register specified by Address. The value written to the PCI
> > + configuration register is returned. This function must guarantee that all PCI
> > + read and write operations are serialized. Extra left bits in both AndData and
> > + OrData are stripped.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If StartBit is greater than 7, then ASSERT().
> > + If EndBit is greater than 7, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..7.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..7.
> > + @param AndData The value to AND with the PCI configuration register.
> > + @param OrData The value to OR with the result of the AND operation.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT8
> > +EFIAPI
> > +PciExpressBitFieldAndThenOr8 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT8 AndData,
> > + IN UINT8 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT8;
> > + }
> > + return MmioBitFieldAndThenOr8 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + AndData,
> > + OrData
> > + );
> > +}
> > +
> > +/**
> > + Reads a 16-bit PCI configuration register.
> > +
> > + Reads and returns the 16-bit PCI configuration register specified by Address.
> > + This function must guarantee that all PCI read and write operations are
> > + serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 16-bit boundary, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > +
> > + @return The read value from the PCI configuration register.
> > +
> > +**/
> > +UINT16
> > +EFIAPI
> > +PciExpressRead16 (
> > + IN UINTN Address
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT16;
> > + }
> > + return MmioRead16 ((UINTN)GetPciExpressBaseAddress () + Address);
> > +}
> > +
> > +/**
> > + Writes a 16-bit PCI configuration register.
> > +
> > + Writes the 16-bit PCI configuration register specified by Address with the
> > + value specified by Value. Value is returned. This function must guarantee
> > + that all PCI read and write operations are serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 16-bit boundary, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param Value The value to write.
> > +
> > + @return The value written to the PCI configuration register.
> > +
> > +**/
> > +UINT16
> > +EFIAPI
> > +PciExpressWrite16 (
> > + IN UINTN Address,
> > + IN UINT16 Value
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT16;
> > + }
> > + return MmioWrite16 ((UINTN)GetPciExpressBaseAddress () + Address, Value);
> > +}
> > +
> > +/**
> > + Performs a bitwise OR of a 16-bit PCI configuration register with
> > + a 16-bit value.
> > +
> > + Reads the 16-bit PCI configuration register specified by Address, performs a
> > + bitwise OR between the read result and the value specified by
> > + OrData, and writes the result to the 16-bit PCI configuration register
> > + specified by Address. The value written to the PCI configuration register is
> > + returned. This function must guarantee that all PCI read and write operations
> > + are serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 16-bit boundary, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param OrData The value to OR with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT16
> > +EFIAPI
> > +PciExpressOr16 (
> > + IN UINTN Address,
> > + IN UINT16 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT16;
> > + }
> > + return MmioOr16 ((UINTN)GetPciExpressBaseAddress () + Address, OrData);
> > +}
> > +
> > +/**
> > + Performs a bitwise AND of a 16-bit PCI configuration register with a 16-bit
> > + value.
> > +
> > + Reads the 16-bit PCI configuration register specified by Address, performs a
> > + bitwise AND between the read result and the value specified by AndData, and
> > + writes the result to the 16-bit PCI configuration register specified by
> > + Address. The value written to the PCI configuration register is returned.
> > + This function must guarantee that all PCI read and write operations are
> > + serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 16-bit boundary, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param AndData The value to AND with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT16
> > +EFIAPI
> > +PciExpressAnd16 (
> > + IN UINTN Address,
> > + IN UINT16 AndData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT16;
> > + }
> > + return MmioAnd16 ((UINTN)GetPciExpressBaseAddress () + Address, AndData);
> > +}
> > +
> > +/**
> > + Performs a bitwise AND of a 16-bit PCI configuration register with a 16-bit
> > + value, followed a bitwise OR with another 16-bit value.
> > +
> > + Reads the 16-bit PCI configuration register specified by Address, performs a
> > + bitwise AND between the read result and the value specified by AndData,
> > + performs a bitwise OR between the result of the AND operation and
> > + the value specified by OrData, and writes the result to the 16-bit PCI
> > + configuration register specified by Address. The value written to the PCI
> > + configuration register is returned. This function must guarantee that all PCI
> > + read and write operations are serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 16-bit boundary, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param AndData The value to AND with the PCI configuration register.
> > + @param OrData The value to OR with the result of the AND operation.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT16
> > +EFIAPI
> > +PciExpressAndThenOr16 (
> > + IN UINTN Address,
> > + IN UINT16 AndData,
> > + IN UINT16 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT16;
> > + }
> > + return MmioAndThenOr16 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + AndData,
> > + OrData
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field of a PCI configuration register.
> > +
> > + Reads the bit field in a 16-bit PCI configuration register. The bit field is
> > + specified by the StartBit and the EndBit. The value of the bit field is
> > + returned.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 16-bit boundary, then ASSERT().
> > + If StartBit is greater than 15, then ASSERT().
> > + If EndBit is greater than 15, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to read.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..15.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..15.
> > +
> > + @return The value of the bit field read from the PCI configuration register.
> > +
> > +**/
> > +UINT16
> > +EFIAPI
> > +PciExpressBitFieldRead16 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT16;
> > + }
> > + return MmioBitFieldRead16 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit
> > + );
> > +}
> > +
> > +/**
> > + Writes a bit field to a PCI configuration register.
> > +
> > + Writes Value to the bit field of the PCI configuration register. The bit
> > + field is specified by the StartBit and the EndBit. All other bits in the
> > + destination PCI configuration register are preserved. The new value of the
> > + 16-bit register is returned.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 16-bit boundary, then ASSERT().
> > + If StartBit is greater than 15, then ASSERT().
> > + If EndBit is greater than 15, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If Value is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..15.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..15.
> > + @param Value The new value of the bit field.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT16
> > +EFIAPI
> > +PciExpressBitFieldWrite16 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT16 Value
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT16;
> > + }
> > + return MmioBitFieldWrite16 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + Value
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field in a 16-bit PCI configuration, performs a bitwise OR, and
> > + writes the result back to the bit field in the 16-bit port.
> > +
> > + Reads the 16-bit PCI configuration register specified by Address, performs a
> > + bitwise OR between the read result and the value specified by
> > + OrData, and writes the result to the 16-bit PCI configuration register
> > + specified by Address. The value written to the PCI configuration register is
> > + returned. This function must guarantee that all PCI read and write operations
> > + are serialized. Extra left bits in OrData are stripped.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 16-bit boundary, then ASSERT().
> > + If StartBit is greater than 15, then ASSERT().
> > + If EndBit is greater than 15, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..15.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..15.
> > + @param OrData The value to OR with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT16
> > +EFIAPI
> > +PciExpressBitFieldOr16 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT16 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT16;
> > + }
> > + return MmioBitFieldOr16 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + OrData
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field in a 16-bit PCI configuration register, performs a bitwise
> > + AND, and writes the result back to the bit field in the 16-bit register.
> > +
> > + Reads the 16-bit PCI configuration register specified by Address, performs a
> > + bitwise AND between the read result and the value specified by AndData, and
> > + writes the result to the 16-bit PCI configuration register specified by
> > + Address. The value written to the PCI configuration register is returned.
> > + This function must guarantee that all PCI read and write operations are
> > + serialized. Extra left bits in AndData are stripped.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 16-bit boundary, then ASSERT().
> > + If StartBit is greater than 15, then ASSERT().
> > + If EndBit is greater than 15, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..15.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..15.
> > + @param AndData The value to AND with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT16
> > +EFIAPI
> > +PciExpressBitFieldAnd16 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT16 AndData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT16;
> > + }
> > + return MmioBitFieldAnd16 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + AndData
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field in a 16-bit port, performs a bitwise AND followed by a
> > + bitwise OR, and writes the result back to the bit field in the
> > + 16-bit port.
> > +
> > + Reads the 16-bit PCI configuration register specified by Address, performs a
> > + bitwise AND followed by a bitwise OR between the read result and
> > + the value specified by AndData, and writes the result to the 16-bit PCI
> > + configuration register specified by Address. The value written to the PCI
> > + configuration register is returned. This function must guarantee that all PCI
> > + read and write operations are serialized. Extra left bits in both AndData and
> > + OrData are stripped.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 16-bit boundary, then ASSERT().
> > + If StartBit is greater than 15, then ASSERT().
> > + If EndBit is greater than 15, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..15.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..15.
> > + @param AndData The value to AND with the PCI configuration register.
> > + @param OrData The value to OR with the result of the AND operation.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT16
> > +EFIAPI
> > +PciExpressBitFieldAndThenOr16 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT16 AndData,
> > + IN UINT16 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT16;
> > + }
> > + return MmioBitFieldAndThenOr16 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + AndData,
> > + OrData
> > + );
> > +}
> > +
> > +/**
> > + Reads a 32-bit PCI configuration register.
> > +
> > + Reads and returns the 32-bit PCI configuration register specified by Address.
> > + This function must guarantee that all PCI read and write operations are
> > + serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 32-bit boundary, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > +
> > + @return The read value from the PCI configuration register.
> > +
> > +**/
> > +UINT32
> > +EFIAPI
> > +PciExpressRead32 (
> > + IN UINTN Address
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT32;
> > + }
> > + return MmioRead32 ((UINTN)GetPciExpressBaseAddress () + Address);
> > +}
> > +
> > +/**
> > + Writes a 32-bit PCI configuration register.
> > +
> > + Writes the 32-bit PCI configuration register specified by Address with the
> > + value specified by Value. Value is returned. This function must guarantee
> > + that all PCI read and write operations are serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 32-bit boundary, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param Value The value to write.
> > +
> > + @return The value written to the PCI configuration register.
> > +
> > +**/
> > +UINT32
> > +EFIAPI
> > +PciExpressWrite32 (
> > + IN UINTN Address,
> > + IN UINT32 Value
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT32;
> > + }
> > + return MmioWrite32 ((UINTN)GetPciExpressBaseAddress () + Address, Value);
> > +}
> > +
> > +/**
> > + Performs a bitwise OR of a 32-bit PCI configuration register with
> > + a 32-bit value.
> > +
> > + Reads the 32-bit PCI configuration register specified by Address, performs a
> > + bitwise OR between the read result and the value specified by
> > + OrData, and writes the result to the 32-bit PCI configuration register
> > + specified by Address. The value written to the PCI configuration register is
> > + returned. This function must guarantee that all PCI read and write operations
> > + are serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 32-bit boundary, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param OrData The value to OR with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT32
> > +EFIAPI
> > +PciExpressOr32 (
> > + IN UINTN Address,
> > + IN UINT32 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT32;
> > + }
> > + return MmioOr32 ((UINTN)GetPciExpressBaseAddress () + Address, OrData);
> > +}
> > +
> > +/**
> > + Performs a bitwise AND of a 32-bit PCI configuration register with a 32-bit
> > + value.
> > +
> > + Reads the 32-bit PCI configuration register specified by Address, performs a
> > + bitwise AND between the read result and the value specified by AndData, and
> > + writes the result to the 32-bit PCI configuration register specified by
> > + Address. The value written to the PCI configuration register is returned.
> > + This function must guarantee that all PCI read and write operations are
> > + serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 32-bit boundary, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param AndData The value to AND with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT32
> > +EFIAPI
> > +PciExpressAnd32 (
> > + IN UINTN Address,
> > + IN UINT32 AndData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT32;
> > + }
> > +return MmioAnd32 ((UINTN)GetPciExpressBaseAddress () + Address, AndData);
> > +}
> > +
> > +/**
> > + Performs a bitwise AND of a 32-bit PCI configuration register with a 32-bit
> > + value, followed a bitwise OR with another 32-bit value.
> > +
> > + Reads the 32-bit PCI configuration register specified by Address, performs a
> > + bitwise AND between the read result and the value specified by AndData,
> > + performs a bitwise OR between the result of the AND operation and
> > + the value specified by OrData, and writes the result to the 32-bit PCI
> > + configuration register specified by Address. The value written to the PCI
> > + configuration register is returned. This function must guarantee that all PCI
> > + read and write operations are serialized.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 32-bit boundary, then ASSERT().
> > +
> > + @param Address The address that encodes the PCI Bus, Device, Function and
> > + Register.
> > + @param AndData The value to AND with the PCI configuration register.
> > + @param OrData The value to OR with the result of the AND operation.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT32
> > +EFIAPI
> > +PciExpressAndThenOr32 (
> > + IN UINTN Address,
> > + IN UINT32 AndData,
> > + IN UINT32 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT32;
> > + }
> > + return MmioAndThenOr32 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + AndData,
> > + OrData
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field of a PCI configuration register.
> > +
> > + Reads the bit field in a 32-bit PCI configuration register. The bit field is
> > + specified by the StartBit and the EndBit. The value of the bit field is
> > + returned.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 32-bit boundary, then ASSERT().
> > + If StartBit is greater than 31, then ASSERT().
> > + If EndBit is greater than 31, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to read.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..31.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..31.
> > +
> > + @return The value of the bit field read from the PCI configuration register.
> > +
> > +**/
> > +UINT32
> > +EFIAPI
> > +PciExpressBitFieldRead32 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT32;
> > + }
> > + return MmioBitFieldRead32 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit
> > + );
> > +}
> > +
> > +/**
> > + Writes a bit field to a PCI configuration register.
> > +
> > + Writes Value to the bit field of the PCI configuration register. The bit
> > + field is specified by the StartBit and the EndBit. All other bits in the
> > + destination PCI configuration register are preserved. The new value of the
> > + 32-bit register is returned.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 32-bit boundary, then ASSERT().
> > + If StartBit is greater than 31, then ASSERT().
> > + If EndBit is greater than 31, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If Value is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..31.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..31.
> > + @param Value The new value of the bit field.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT32
> > +EFIAPI
> > +PciExpressBitFieldWrite32 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT32 Value
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT32;
> > + }
> > + return MmioBitFieldWrite32 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + Value
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field in a 32-bit PCI configuration, performs a bitwise OR, and
> > + writes the result back to the bit field in the 32-bit port.
> > +
> > + Reads the 32-bit PCI configuration register specified by Address, performs a
> > + bitwise OR between the read result and the value specified by
> > + OrData, and writes the result to the 32-bit PCI configuration register
> > + specified by Address. The value written to the PCI configuration register is
> > + returned. This function must guarantee that all PCI read and write operations
> > + are serialized. Extra left bits in OrData are stripped.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 32-bit boundary, then ASSERT().
> > + If StartBit is greater than 31, then ASSERT().
> > + If EndBit is greater than 31, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..31.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..31.
> > + @param OrData The value to OR with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT32
> > +EFIAPI
> > +PciExpressBitFieldOr32 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT32 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT32;
> > + }
> > + return MmioBitFieldOr32 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + OrData
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field in a 32-bit PCI configuration register, performs a bitwise
> > + AND, and writes the result back to the bit field in the 32-bit register.
> > +
> > + Reads the 32-bit PCI configuration register specified by Address, performs a
> > + bitwise AND between the read result and the value specified by AndData, and
> > + writes the result to the 32-bit PCI configuration register specified by
> > + Address. The value written to the PCI configuration register is returned.
> > + This function must guarantee that all PCI read and write operations are
> > + serialized. Extra left bits in AndData are stripped.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 32-bit boundary, then ASSERT().
> > + If StartBit is greater than 31, then ASSERT().
> > + If EndBit is greater than 31, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..31.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..31.
> > + @param AndData The value to AND with the PCI configuration register.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT32
> > +EFIAPI
> > +PciExpressBitFieldAnd32 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT32 AndData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT32;
> > + }
> > + return MmioBitFieldAnd32 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + AndData
> > + );
> > +}
> > +
> > +/**
> > + Reads a bit field in a 32-bit port, performs a bitwise AND followed by a
> > + bitwise OR, and writes the result back to the bit field in the
> > + 32-bit port.
> > +
> > + Reads the 32-bit PCI configuration register specified by Address, performs a
> > + bitwise AND followed by a bitwise OR between the read result and
> > + the value specified by AndData, and writes the result to the 32-bit PCI
> > + configuration register specified by Address. The value written to the PCI
> > + configuration register is returned. This function must guarantee that all PCI
> > + read and write operations are serialized. Extra left bits in both AndData and
> > + OrData are stripped.
> > +
> > + If Address > 0x0FFFFFFF, then ASSERT().
> > + If Address is not aligned on a 32-bit boundary, then ASSERT().
> > + If StartBit is greater than 31, then ASSERT().
> > + If EndBit is greater than 31, then ASSERT().
> > + If EndBit is less than StartBit, then ASSERT().
> > + If AndData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > + If OrData is larger than the bitmask value range specified by StartBit and EndBit, then ASSERT().
> > +
> > + @param Address The PCI configuration register to write.
> > + @param StartBit The ordinal of the least significant bit in the bit field.
> > + Range 0..31.
> > + @param EndBit The ordinal of the most significant bit in the bit field.
> > + Range 0..31.
> > + @param AndData The value to AND with the PCI configuration register.
> > + @param OrData The value to OR with the result of the AND operation.
> > +
> > + @return The value written back to the PCI configuration register.
> > +
> > +**/
> > +UINT32
> > +EFIAPI
> > +PciExpressBitFieldAndThenOr32 (
> > + IN UINTN Address,
> > + IN UINTN StartBit,
> > + IN UINTN EndBit,
> > + IN UINT32 AndData,
> > + IN UINT32 OrData
> > + )
> > +{
> > + ASSERT_INVALID_PCI_ADDRESS (Address);
> > + if (IgnoreBusDeviceFunction (Address)) {
> > + return MAX_UINT32;
> > + }
> > + return MmioBitFieldAndThenOr32 (
> > + (UINTN)GetPciExpressBaseAddress () + Address,
> > + StartBit,
> > + EndBit,
> > + AndData,
> > + OrData
> > + );
> > +}
> > +
> > +/**
> > + Reads a range of PCI configuration registers into a caller supplied buffer.
> > +
> > + Reads the range of PCI configuration registers specified by StartAddress and
> > + Size into the buffer specified by Buffer. This function only allows the PCI
> > + configuration registers from a single PCI function to be read. Size is
> > + returned. When possible 32-bit PCI configuration read cycles are used to read
> > + from StartAddress to StartAddress + Size. Due to alignment restrictions, 8-bit
> > + and 16-bit PCI configuration read cycles may be used at the beginning and the
> > + end of the range.
> > +
> > + If StartAddress > 0x0FFFFFFF, then ASSERT().
> > + If ((StartAddress & 0xFFF) + Size) > 0x1000, then ASSERT().
> > + If Size > 0 and Buffer is NULL, then ASSERT().
> > +
> > + @param StartAddress The starting address that encodes the PCI Bus, Device,
> > + Function and Register.
> > + @param Size The size in bytes of the transfer.
> > + @param Buffer The pointer to a buffer receiving the data read.
> > +
> > + @return Size read data from StartAddress.
> > +
> > +**/
> > +UINTN
> > +EFIAPI
> > +PciExpressReadBuffer (
> > + IN UINTN StartAddress,
> > + IN UINTN Size,
> > + OUT VOID *Buffer
> > + )
> > +{
> > + UINTN ReturnValue;
> > +
> > + ASSERT_INVALID_PCI_ADDRESS (StartAddress);
> > + ASSERT (((StartAddress & 0xFFF) + Size) <= 0x1000);
> > +
> > + if (Size == 0) {
> > + return Size;
> > + }
> > +
> > + ASSERT (Buffer != NULL);
> > +
> > + //
> > + // Save Size for return
> > + //
> > + ReturnValue = Size;
> > +
> > + if ((StartAddress & 1) != 0) {
> > + //
> > + // Read a byte if StartAddress is byte aligned
> > + //
> > + MmioWrite8 ((UINTN)Buffer, PciExpressRead8 (StartAddress));
> > + StartAddress += sizeof (UINT8);
> > + Size -= sizeof (UINT8);
> > + Buffer = (UINT8 *)Buffer + 1;
> > + }
> > +
> > + if (Size >= sizeof (UINT16)&& (StartAddress & 2) != 0) {
> > + //
> > + // Read a word if StartAddress is word aligned
> > + //
> > + WriteUnaligned16 ((UINT16 *)Buffer, (UINT16)PciExpressRead16 (StartAddress));
> > +
> > + StartAddress += sizeof (UINT16);
> > + Size -= sizeof (UINT16);
> > + Buffer = (UINT16 *)Buffer + 1;
> > + }
> > +
> > + while (Size >= sizeof (UINT32)) {
> > + //
> > + // Read as many double words as possible
> > + //
> > + WriteUnaligned32 ((UINT32 *)Buffer, (UINT32)PciExpressRead32 (StartAddress));
> > +
> > + StartAddress += sizeof (UINT32);
> > + Size -= sizeof (UINT32);
> > + Buffer = (UINT32 *)Buffer + 1;
> > + }
> > +
> > + if (Size >= sizeof (UINT16)) {
> > + //
> > + // Read the last remaining word if exist
> > + //
> > + WriteUnaligned16 ((UINT16 *)Buffer, (UINT16)PciExpressRead16 (StartAddress));
> > + StartAddress += sizeof (UINT16);
> > + Size -= sizeof (UINT16);
> > + Buffer = (UINT16 *)Buffer + 1;
> > + }
> > +
> > + if (Size >= sizeof (UINT8)) {
> > + //
> > + // Read the last remaining byte if exist
> > + //
> > + MmioWrite8 ((UINTN)Buffer, PciExpressRead8 (StartAddress));
> > + }
> > +
> > + return ReturnValue;
> > +}
> > +
> > +/**
> > + Copies the data in a caller supplied buffer to a specified range of PCI
> > + configuration space.
> > +
> > + Writes the range of PCI configuration registers specified by StartAddress and
> > + Size from the buffer specified by Buffer. This function only allows the PCI
> > + configuration registers from a single PCI function to be written. Size is
> > + returned. When possible 32-bit PCI configuration write cycles are used to
> > + write from StartAddress to StartAddress + Size. Due to alignment restrictions,
> > + 8-bit and 16-bit PCI configuration write cycles may be used at the beginning
> > + and the end of the range.
> > +
> > + If StartAddress > 0x0FFFFFFF, then ASSERT().
> > + If ((StartAddress & 0xFFF) + Size) > 0x1000, then ASSERT().
> > + If Size > 0 and Buffer is NULL, then ASSERT().
> > +
> > + @param StartAddress The starting address that encodes the PCI Bus, Device,
> > + Function and Register.
> > + @param Size The size in bytes of the transfer.
> > + @param Buffer The pointer to a buffer containing the data to write.
> > +
> > + @return Size written to StartAddress.
> > +
> > +**/
> > +UINTN
> > +EFIAPI
> > +PciExpressWriteBuffer (
> > + IN UINTN StartAddress,
> > + IN UINTN Size,
> > + IN VOID *Buffer
> > + )
> > +{
> > + UINTN ReturnValue;
> > +
> > + ASSERT_INVALID_PCI_ADDRESS (StartAddress);
> > + ASSERT (((StartAddress & 0xFFF) + Size) <= 0x1000);
> > +
> > + if (Size == 0) {
> > + return 0;
> > + }
> > +
> > + ASSERT (Buffer != NULL);
> > +
> > + //
> > + // Save Size for return
> > + //
> > + ReturnValue = Size;
> > +
> > + if ((StartAddress & 1) != 0) {
> > + //
> > + // Write a byte if StartAddress is byte aligned
> > + //
> > + PciExpressWrite8 (StartAddress, *(UINT8 *)Buffer);
> > + StartAddress += sizeof (UINT8);
> > + Size -= sizeof (UINT8);
> > + Buffer = (UINT8 *)Buffer + 1;
> > + }
> > +
> > + if (Size >= sizeof (UINT16) && (StartAddress & 2) != 0) {
> > + //
> > + // Write a word if StartAddress is word aligned
> > + //
> > + PciExpressWrite16 (StartAddress, ReadUnaligned16 ((UINT16 *)Buffer));
> > + StartAddress += sizeof (UINT16);
> > + Size -= sizeof (UINT16);
> > + Buffer = (UINT16 *)Buffer + 1;
> > + }
> > +
> > + while (Size >= sizeof (UINT32)) {
> > + //
> > + // Write as many double words as possible
> > + //
> > + PciExpressWrite32 (StartAddress, ReadUnaligned32 ((UINT32 *)Buffer));
> > + StartAddress += sizeof (UINT32);
> > + Size -= sizeof (UINT32);
> > + Buffer = (UINT32 *)Buffer + 1;
> > + }
> > +
> > + if (Size >= sizeof (UINT16)) {
> > + //
> > + // Write the last remaining word if exist
> > + //
> > + PciExpressWrite16 (StartAddress, ReadUnaligned16 ((UINT16 *)Buffer));
> > + StartAddress += sizeof (UINT16);
> > + Size -= sizeof (UINT16);
> > + Buffer = (UINT16 *)Buffer + 1;
> > + }
> > +
> > + if (Size >= sizeof (UINT8)) {
> > + //
> > + // Write the last remaining byte if exist
> > + //
> > + PciExpressWrite8 (StartAddress, *(UINT8 *)Buffer);
> > + }
> > +
> > + return ReturnValue;
> > +}
> > --
> > 2.7.4
> >
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation
2019-05-24 13:03 ` Marcin Wojtas
@ 2019-05-24 13:08 ` Ard Biesheuvel
2019-05-24 14:28 ` Marcin Wojtas
0 siblings, 1 reply; 34+ messages in thread
From: Ard Biesheuvel @ 2019-05-24 13:08 UTC (permalink / raw)
To: Marcin Wojtas
Cc: edk2-devel-groups-io, Leif Lindholm, Jan Dąbroś,
Grzegorz Jaszczyk, Kostya Porotchkin, Jici Gao, Rebecca Cran,
Mark Kettenis
On Fri, 24 May 2019 at 15:03, Marcin Wojtas <mw@semihalf.com> wrote:
>
> pt., 24 maj 2019 o 14:50 Ard Biesheuvel <ard.biesheuvel@linaro.org> napisał(a):
> >
> > On Mon, 20 May 2019 at 17:27, Marcin Wojtas <mw@semihalf.com> wrote:
> > >
> > > From: Ard Biesheuvel <ard.biesheuvel@linaro.org>
> > >
> > > Implement a special version of PciExpressLib that takes the quirky
> > > nature of the Synopsys Designware PCIe IP into account. In particular,
> > > we need to ignore config space accesses to all devices on the first
> > > bus except device 0, because the broadcast nature of type 0 configuration
> > > cycles will result in whatever device is in the slot to appear at each
> > > of the 32 device positions.
> > >
> >
> > I never bothered to implement multisegment support for this SoC, since
> > MacchiatoBin has only one segment wired up, but since your interest is
> > in generic support, it might make sense to drop this patch and
> > implement PciSegmentLib instead (without depending on any of the other
> > library classes that the generic PciExpressLib depends on)
> >
>
> This was (and still is) my plan, but I've been having some serious
> time shortages for extra development. In order not to postpone this
> support any longer I prefer to get merged, what I have and possibly
> rework on top.
>
> About depending on a generic PciExpressLib - do you mean I can filter
> out devices from bus0 in PciSegmentLib?
>
Yes, please look at Silicon/Socionext/SynQuacer/Library/SynQuacerPciSegmentLib
If you follow the same approach, you no longer need PciLib or
PciExpressLib, it is all flattened into PciSegmentLib.
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
2019-05-23 20:24 ` Ard Biesheuvel
@ 2019-05-24 13:08 ` Marcin Wojtas
2019-05-24 13:12 ` Ard Biesheuvel
0 siblings, 1 reply; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-24 13:08 UTC (permalink / raw)
To: Ard Biesheuvel
Cc: Leif Lindholm, Mark Kettenis, edk2-devel-groups-io,
Jan Dąbroś, Grzegorz Jaszczyk, Kostya Porotchkin,
Jici Gao, Rebecca Cran, kettenis
Hi Ard,
czw., 23 maj 2019 o 22:24 Ard Biesheuvel <ard.biesheuvel@linaro.org> napisał(a):
>
> On Thu, 23 May 2019 at 21:11, Leif Lindholm <leif.lindholm@linaro.org> wrote:
> >
> > On Thu, May 23, 2019 at 07:13:20PM +0100, Ard Biesheuvel wrote:
> > > > Connect: PcieRoot(0x0)/Pci(0x0,0x0): Not Found
> > > >
> > > > Hmm, that's actually interesting. Maybe I should play with the X86
> > > > emulator that Ard added recently to see if that gives me a framebuffer
> > > > console.
> > > >
> > >
> > > Yes, if you add edk2-staging to your PACKAGES_PATH env variable, all
> > > you need to do is add -D X64EMU_ENABLE to the build command line.
> >
> > You mean edk2-non-osi, right?
> >
>
> Of course :-)
The video is not perfect (taken in Semihalf lab), but here's an output
from GT630 directly from UEFI and your X64 emulation (thanks for it!):
https://drive.google.com/file/d/1l8gyPI6boMtPaO89W7U9rn0ztQi_zrwZ/view
Actually that may be first ever launch of it on this board :) Once the
PCIe series gets merged, I'm considering some better footage booting
to distro with GPU and promote a bit via my company's SM.
Best regards,
Marcin
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
2019-05-24 13:08 ` Marcin Wojtas
@ 2019-05-24 13:12 ` Ard Biesheuvel
2019-05-24 13:13 ` Marcin Wojtas
0 siblings, 1 reply; 34+ messages in thread
From: Ard Biesheuvel @ 2019-05-24 13:12 UTC (permalink / raw)
To: Marcin Wojtas
Cc: Leif Lindholm, Mark Kettenis, edk2-devel-groups-io,
Jan Dąbroś, Grzegorz Jaszczyk, Kostya Porotchkin,
Jici Gao, Rebecca Cran, kettenis
On Fri, 24 May 2019 at 15:08, Marcin Wojtas <mw@semihalf.com> wrote:
>
> Hi Ard,
>
> czw., 23 maj 2019 o 22:24 Ard Biesheuvel <ard.biesheuvel@linaro.org> napisał(a):
> >
> > On Thu, 23 May 2019 at 21:11, Leif Lindholm <leif.lindholm@linaro.org> wrote:
> > >
> > > On Thu, May 23, 2019 at 07:13:20PM +0100, Ard Biesheuvel wrote:
> > > > > Connect: PcieRoot(0x0)/Pci(0x0,0x0): Not Found
> > > > >
> > > > > Hmm, that's actually interesting. Maybe I should play with the X86
> > > > > emulator that Ard added recently to see if that gives me a framebuffer
> > > > > console.
> > > > >
> > > >
> > > > Yes, if you add edk2-staging to your PACKAGES_PATH env variable, all
> > > > you need to do is add -D X64EMU_ENABLE to the build command line.
> > >
> > > You mean edk2-non-osi, right?
> > >
> >
> > Of course :-)
>
> The video is not perfect (taken in Semihalf lab), but here's an output
> from GT630 directly from UEFI and your X64 emulation (thanks for it!):
> https://drive.google.com/file/d/1l8gyPI6boMtPaO89W7U9rn0ztQi_zrwZ/view
Thanks! So GT630 is Nvidia Geforce, right?
> Actually that may be first ever launch of it on this board :)
Launch of what? The emulator? I've had that running on MacchiatoBin
for years :-)
> Once the
> PCIe series gets merged, I'm considering some better footage booting
> to distro with GPU and promote a bit via my company's SM.
>
> Best regards,
> Marcin
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
2019-05-24 13:12 ` Ard Biesheuvel
@ 2019-05-24 13:13 ` Marcin Wojtas
0 siblings, 0 replies; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-24 13:13 UTC (permalink / raw)
To: Ard Biesheuvel
Cc: Leif Lindholm, Mark Kettenis, edk2-devel-groups-io,
Jan Dąbroś, Grzegorz Jaszczyk, Kostya Porotchkin,
Jici Gao, Rebecca Cran, kettenis
pt., 24 maj 2019 o 15:12 Ard Biesheuvel <ard.biesheuvel@linaro.org> napisał(a):
>
> On Fri, 24 May 2019 at 15:08, Marcin Wojtas <mw@semihalf.com> wrote:
> >
> > Hi Ard,
> >
> > czw., 23 maj 2019 o 22:24 Ard Biesheuvel <ard.biesheuvel@linaro.org> napisał(a):
> > >
> > > On Thu, 23 May 2019 at 21:11, Leif Lindholm <leif.lindholm@linaro.org> wrote:
> > > >
> > > > On Thu, May 23, 2019 at 07:13:20PM +0100, Ard Biesheuvel wrote:
> > > > > > Connect: PcieRoot(0x0)/Pci(0x0,0x0): Not Found
> > > > > >
> > > > > > Hmm, that's actually interesting. Maybe I should play with the X86
> > > > > > emulator that Ard added recently to see if that gives me a framebuffer
> > > > > > console.
> > > > > >
> > > > >
> > > > > Yes, if you add edk2-staging to your PACKAGES_PATH env variable, all
> > > > > you need to do is add -D X64EMU_ENABLE to the build command line.
> > > >
> > > > You mean edk2-non-osi, right?
> > > >
> > >
> > > Of course :-)
> >
> > The video is not perfect (taken in Semihalf lab), but here's an output
> > from GT630 directly from UEFI and your X64 emulation (thanks for it!):
> > https://drive.google.com/file/d/1l8gyPI6boMtPaO89W7U9rn0ztQi_zrwZ/view
>
> Thanks! So GT630 is Nvidia Geforce, right?
Yes.
>
> > Actually that may be first ever launch of it on this board :)
>
> Launch of what? The emulator? I've had that running on MacchiatoBin
> for years :-)
>
So first one on my board ;)
Thanks,
Marcin
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation
2019-05-24 13:08 ` Ard Biesheuvel
@ 2019-05-24 14:28 ` Marcin Wojtas
2019-05-24 15:25 ` Ard Biesheuvel
0 siblings, 1 reply; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-24 14:28 UTC (permalink / raw)
To: Ard Biesheuvel
Cc: edk2-devel-groups-io, Leif Lindholm, Jan Dąbroś,
Grzegorz Jaszczyk, Kostya Porotchkin, Jici Gao, Rebecca Cran,
Mark Kettenis
pt., 24 maj 2019 o 15:08 Ard Biesheuvel <ard.biesheuvel@linaro.org> napisał(a):
>
> On Fri, 24 May 2019 at 15:03, Marcin Wojtas <mw@semihalf.com> wrote:
> >
> > pt., 24 maj 2019 o 14:50 Ard Biesheuvel <ard.biesheuvel@linaro.org> napisał(a):
> > >
> > > On Mon, 20 May 2019 at 17:27, Marcin Wojtas <mw@semihalf.com> wrote:
> > > >
> > > > From: Ard Biesheuvel <ard.biesheuvel@linaro.org>
> > > >
> > > > Implement a special version of PciExpressLib that takes the quirky
> > > > nature of the Synopsys Designware PCIe IP into account. In particular,
> > > > we need to ignore config space accesses to all devices on the first
> > > > bus except device 0, because the broadcast nature of type 0 configuration
> > > > cycles will result in whatever device is in the slot to appear at each
> > > > of the 32 device positions.
> > > >
> > >
> > > I never bothered to implement multisegment support for this SoC, since
> > > MacchiatoBin has only one segment wired up, but since your interest is
> > > in generic support, it might make sense to drop this patch and
> > > implement PciSegmentLib instead (without depending on any of the other
> > > library classes that the generic PciExpressLib depends on)
> > >
> >
> > This was (and still is) my plan, but I've been having some serious
> > time shortages for extra development. In order not to postpone this
> > support any longer I prefer to get merged, what I have and possibly
> > rework on top.
> >
> > About depending on a generic PciExpressLib - do you mean I can filter
> > out devices from bus0 in PciSegmentLib?
> >
>
> Yes, please look at Silicon/Socionext/SynQuacer/Library/SynQuacerPciSegmentLib
>
> If you follow the same approach, you no longer need PciLib or
> PciExpressLib, it is all flattened into PciSegmentLib.
For PciLib I use MdePkg implementation, but if that could be dropped
that's good. I saw your library and it would be perfect for reusing on
Armada, with one difference: PciSegmentLibGetConfigBase.
1. As a first step I could reuse Synquacer library using single base
in PciSegmentLibGetConfigBase (PcdPciExpressBaseAddress) as a stub,
for extending later.
2. Afterwards (i.e. in some next patchset) I'd like to use my board
description infrastructure for obtaining config space base addresses.
How about following solution:
- add PciSegmentLib constructor routine, where I'd create a global
array with config space addesses
- add dispatching for it in PciSegmentLibGetConfigBase?
Looking forward to your feedback. Other than that - do you have any
remarks to the rest of the patches in v2?
Thanks,
Marcin
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation
2019-05-24 14:28 ` Marcin Wojtas
@ 2019-05-24 15:25 ` Ard Biesheuvel
2019-05-24 15:32 ` Leif Lindholm
0 siblings, 1 reply; 34+ messages in thread
From: Ard Biesheuvel @ 2019-05-24 15:25 UTC (permalink / raw)
To: Marcin Wojtas
Cc: edk2-devel-groups-io, Leif Lindholm, Jan Dąbroś,
Grzegorz Jaszczyk, Kostya Porotchkin, Jici Gao, Rebecca Cran,
Mark Kettenis
On Fri, 24 May 2019 at 16:28, Marcin Wojtas <mw@semihalf.com> wrote:
>
> pt., 24 maj 2019 o 15:08 Ard Biesheuvel <ard.biesheuvel@linaro.org> napisał(a):
> >
> > On Fri, 24 May 2019 at 15:03, Marcin Wojtas <mw@semihalf.com> wrote:
> > >
> > > pt., 24 maj 2019 o 14:50 Ard Biesheuvel <ard.biesheuvel@linaro.org> napisał(a):
> > > >
> > > > On Mon, 20 May 2019 at 17:27, Marcin Wojtas <mw@semihalf.com> wrote:
> > > > >
> > > > > From: Ard Biesheuvel <ard.biesheuvel@linaro.org>
> > > > >
> > > > > Implement a special version of PciExpressLib that takes the quirky
> > > > > nature of the Synopsys Designware PCIe IP into account. In particular,
> > > > > we need to ignore config space accesses to all devices on the first
> > > > > bus except device 0, because the broadcast nature of type 0 configuration
> > > > > cycles will result in whatever device is in the slot to appear at each
> > > > > of the 32 device positions.
> > > > >
> > > >
> > > > I never bothered to implement multisegment support for this SoC, since
> > > > MacchiatoBin has only one segment wired up, but since your interest is
> > > > in generic support, it might make sense to drop this patch and
> > > > implement PciSegmentLib instead (without depending on any of the other
> > > > library classes that the generic PciExpressLib depends on)
> > > >
> > >
> > > This was (and still is) my plan, but I've been having some serious
> > > time shortages for extra development. In order not to postpone this
> > > support any longer I prefer to get merged, what I have and possibly
> > > rework on top.
> > >
> > > About depending on a generic PciExpressLib - do you mean I can filter
> > > out devices from bus0 in PciSegmentLib?
> > >
> >
> > Yes, please look at Silicon/Socionext/SynQuacer/Library/SynQuacerPciSegmentLib
> >
> > If you follow the same approach, you no longer need PciLib or
> > PciExpressLib, it is all flattened into PciSegmentLib.
>
> For PciLib I use MdePkg implementation, but if that could be dropped
> that's good. I saw your library and it would be perfect for reusing on
> Armada, with one difference: PciSegmentLibGetConfigBase.
>
> 1. As a first step I could reuse Synquacer library using single base
> in PciSegmentLibGetConfigBase (PcdPciExpressBaseAddress) as a stub,
> for extending later.
>
> 2. Afterwards (i.e. in some next patchset) I'd like to use my board
> description infrastructure for obtaining config space base addresses.
> How about following solution:
> - add PciSegmentLib constructor routine, where I'd create a global
> array with config space addesses
> - add dispatching for it in PciSegmentLibGetConfigBase?
>
This sounds like a reasonable approach, yes.
> Looking forward to your feedback. Other than that - do you have any
> remarks to the rest of the patches in v2?
>
The rest looks fine.
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation
2019-05-24 15:25 ` Ard Biesheuvel
@ 2019-05-24 15:32 ` Leif Lindholm
2019-05-24 15:43 ` Marcin Wojtas
0 siblings, 1 reply; 34+ messages in thread
From: Leif Lindholm @ 2019-05-24 15:32 UTC (permalink / raw)
To: Ard Biesheuvel, Marcin Wojtas
Cc: edk2-devel-groups-io, Jan Dąbroś, Grzegorz Jaszczyk,
Kostya Porotchkin, Jici Gao, Rebecca Cran, Mark Kettenis
> > Looking forward to your feedback. Other than that - do you have any
> > remarks to the rest of the patches in v2?
>
> The rest looks fine.
And I'm happy that all of my comments on v1 have been addressed.
/
Leif
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation
2019-05-24 15:32 ` Leif Lindholm
@ 2019-05-24 15:43 ` Marcin Wojtas
2019-05-24 15:46 ` Ard Biesheuvel
0 siblings, 1 reply; 34+ messages in thread
From: Marcin Wojtas @ 2019-05-24 15:43 UTC (permalink / raw)
To: Leif Lindholm
Cc: Ard Biesheuvel, edk2-devel-groups-io, Jan Dąbroś,
Grzegorz Jaszczyk, Kostya Porotchkin, Jici Gao, Rebecca Cran,
Mark Kettenis
pt., 24 maj 2019 o 17:32 Leif Lindholm <leif.lindholm@linaro.org> napisał(a):
>
> > > Looking forward to your feedback. Other than that - do you have any
> > > remarks to the rest of the patches in v2?
> >
> > The rest looks fine.
>
> And I'm happy that all of my comments on v1 have been addressed.
>
Great, thanks. Ok, with PciSegmentLib it's still working. Should I
resubmit the whole patchset?
Best regards,
Marcin
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation
2019-05-24 15:43 ` Marcin Wojtas
@ 2019-05-24 15:46 ` Ard Biesheuvel
0 siblings, 0 replies; 34+ messages in thread
From: Ard Biesheuvel @ 2019-05-24 15:46 UTC (permalink / raw)
To: Marcin Wojtas
Cc: Leif Lindholm, edk2-devel-groups-io, Jan Dąbroś,
Grzegorz Jaszczyk, Kostya Porotchkin, Jici Gao, Rebecca Cran,
Mark Kettenis
On Fri, 24 May 2019 at 17:43, Marcin Wojtas <mw@semihalf.com> wrote:
>
> pt., 24 maj 2019 o 17:32 Leif Lindholm <leif.lindholm@linaro.org> napisał(a):
> >
> > > > Looking forward to your feedback. Other than that - do you have any
> > > > remarks to the rest of the patches in v2?
> > >
> > > The rest looks fine.
> >
> > And I'm happy that all of my comments on v1 have been addressed.
> >
>
> Great, thanks. Ok, with PciSegmentLib it's still working. Should I
> resubmit the whole patchset?
>
Yes, please.
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
2019-05-23 18:13 ` Ard Biesheuvel
2019-05-23 20:11 ` Leif Lindholm
@ 2019-05-24 22:16 ` mark.kettenis
2019-05-25 9:47 ` Ard Biesheuvel
1 sibling, 1 reply; 34+ messages in thread
From: mark.kettenis @ 2019-05-24 22:16 UTC (permalink / raw)
To: Ard Biesheuvel
Cc: leif.lindholm, mw, devel, jsd, jaz, kostap, Jici.Gao, rebecca,
kettenis
> From: Ard Biesheuvel <ard.biesheuvel@linaro.org>
> Date: Thu, 23 May 2019 19:13:20 +0100
> Cc: Leif Lindholm <leif.lindholm@linaro.org>, Marcin Wojtas <mw@semihalf.com>,
> edk2-devel-groups-io <devel@edk2.groups.io>,
> Jan Dąbroś <jsd@semihalf.com>,
> Grzegorz Jaszczyk <jaz@semihalf.com>,
> Kostya Porotchkin <kostap@marvell.com>, Jici Gao <Jici.Gao@arm.com>,
> Rebecca Cran <rebecca@bluestop.org>, kettenis@openbsd.org
> Content-Type: text/plain; charset="UTF-8"
>
> On Thu, 23 May 2019 at 19:02, Mark Kettenis <kettenis@jive.eu> wrote:
> >
> > > Date: Thu, 23 May 2019 15:14:27 +0100
> > > From: Leif Lindholm <leif.lindholm@linaro.org>
> > >
> > > On Thu, May 23, 2019 at 03:27:47PM +0200, Mark Kettenis wrote:
> > > > > From: Marcin Wojtas <mw@semihalf.com>
> > > > > Date: Mon, 20 May 2019 17:27:13 +0200
> > > > >
> > > > > Hi,
> > > > >
> > > > > Thank you for thorough review of v1. I submit second
> > > > > version of the Armada7k8k PCIE support. I addressed
> > > > > all comments. There is no functional change to initial
> > > > > patchset, but mostly clean-up and improvements - please
> > > > > refer to the changelog below.
> > > > >
> > > > > The patches are available in the github:
> > > > > https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/commits/pcie-upstream-r20190520
> > > > >
> > > > > I'm looking forward to your comments or remarks.
> > > > >
> > > > > Best regards,
> > > > > Marcin
> > > >
> > > > Tested this on my mcbin running OpenBSD. It incovers a small issue in
> > > > our kernel which I'm fixing. Otherwise this seems to work fine.
> > > >
> > > > So tested-by: Mark Kettenis <kettenis@openbsd.org> if that matters.
> > >
> > > Always helpful, thanks.
> > >
> > > Out of interest, what was the issue?
> > > Could I still expect the 6.5 installer to run on this
> > > hardware/firmware combo?
> >
> > That should still work fine.
> >
> > The issue is with mapping PCI ROMS, which currently fails with the new
> > firmware due to an oversight in the OpenBSD code. There are only a
> > few OpenBSD drivers that attempt to map the PCI ROM. But one of those
> > is radeondrm(4) and I stuck an AMD graphics card into the PCIe slot on
> > my machine.
> >
> > There is a bit of a firmware angle to this though. The issue happens
> > because the PCI ROM address register has been set to 0xfffe0000. All
> > the writable address bits in the register are set to 1. While it is
> > possible that the hardware comes up in that state, I suspect this is
> > done by an attempt by the firmware to determine the size of the ROM
> > that doesn't properly restore the original contents of the register.
>
> UEFI deliberately leaves the ROM BARs unassigned, in order to avoid
> wasting valuable 32-bit PCI MMIO space. It enables the BAR temporarily
> to load the ROM, and dispatches it if it can. After that, it changes
> the BAR back to the old unassigned value.
It seems that that last bit isn't working...
> > It may be related to the following messages that are printed by the
> > firmware:
> >
> > Image type X64 can't be loaded on AARCH64 UEFI system.
> > Unloading driver at 0x00000000000
>
> That address value is quite unexpected.
>
> > Connect: PcieRoot(0x0)/Pci(0x0,0x0): Not Found
> >
> > Hmm, that's actually interesting. Maybe I should play with the X86
> > emulator that Ard added recently to see if that gives me a framebuffer
> > console.
> >
>
> Yes, if you add edk2-staging to your PACKAGES_PATH env variable, all
> you need to do is add -D X64EMU_ENABLE to the build command line.
>
> If you do end up testing this, could you please report back with the
> result, i.e., the type of card, PCI PID/VID and whether it all worked
> as expected? Thanks.
Seems to work fine. The EFI shell and OpenBSD bootloader prompt show
up on both the framebuffer and the serial console. Here is a dmesg:
OpenBSD 6.5-current (GENERIC.MP) #2: Fri May 24 12:25:38 CEST 2019
kettenis@caldara.sibelius.xs4all.nl:/usr/src/sys/arch/arm64/compile/GENERIC.MP
real mem = 4095279104 (3905MB)
avail mem = 3936260096 (3753MB)
mainbus0 at root: ACPI
cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p1
cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu0: 512KB 64b/line 16-way L2 cache
efi0 at mainbus0: UEFI 2.7
efi0: EDK II rev 0x10000
apm0 at mainbus0
psci0 at mainbus0: PSCI 1.1, SMCCC 1.1
ampintc0 at mainbus0 nirq 352, ncpu 4 ipi: 0, 1: "interrupt-controller"
ampintcmsi0 at ampintc0: nspi 32
ampintcmsi1 at ampintc0: nspi 32
ampintcmsi2 at ampintc0: nspi 32
ampintcmsi3 at ampintc0: nspi 32
agtimer0 at mainbus0: tick rate 25000 KHz
acpi0 at mainbus0: rev 2
acpi0: sleep states
acpi0: tables DSDT FACP MCFG GTDT APIC PPTT SPCR VFCT
acpi0: wakeup devices
acpimcfg0 at acpi0
acpimcfg0: addr 0xe0008000, bus 0-0
"ACPI0007" at acpi0 not configured
"ACPI0007" at acpi0 not configured
"ACPI0007" at acpi0 not configured
"ACPI0007" at acpi0 not configured
ahci0 at acpi0 AHC0 addr 0xf2540000/0x2000 irq 114: AHCI 1.0
scsibus0 at ahci0: 32 targets
ahci1 at acpi0 AHC1 addr 0xf4540000/0x2000 irq 338: AHCI 1.0
ahci1: port busy after first PMP probe FIS
ahci1: port busy after first PMP probe FIS
ahci1: port 1: 6.0Gb/s
scsibus1 at ahci1: 32 targets
sd0 at scsibus1 targ 1 lun 0: <ATA, Samsung SSD 850, EMT0> SCSI3 0/direct fixed naa.5002538d42110a27
sd0: 238475MB, 512 bytes/sector, 488397168 sectors, thin
xhci0 at acpi0 XHC0 addr 0xf2500000/0x4000 irq 113, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1
xhci1 at acpi0 XHC1 addr 0xf2510000/0x4000 irq 112, xHCI 1.0
usb1 at xhci1: USB revision 3.0
uhub1 at usb1 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1
xhci2 at acpi0 XHC2 addr 0xf4500000/0x4000 irq 337, xHCI 1.0
usb2 at xhci2: USB revision 3.0
uhub2 at usb2 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1
com0 at acpi0 COM1 addr 0xf0512000/0x100 irq 51: ns16550, no working fifo
com0: console
"MRVL0110" at acpi0 not configured
"MRVL0110" at acpi0 not configured
"PRP0001" at acpi0 not configured
"PRP0001" at acpi0 not configured
acpipci0 at acpi0 PCI0
pci0 at acpipci0
0:0:0: mem address conflict 0xfffe0000/0x20000
radeondrm0 at pci0 dev 0 function 0 "ATI Radeon HD 7450" rev 0x00
drm0 at radeondrm0
radeondrm0: msi
"ATI Radeon HD 6400 Audio" rev 0x00 at pci0 dev 0 function 1 not configured
"framebuffer" at mainbus0 not configured
cpu1 at mainbus0 mpidr 1: ARM Cortex-A72 r0p1
cpu1: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu1: 512KB 64b/line 16-way L2 cache
cpu2 at mainbus0 mpidr 100: ARM Cortex-A72 r0p1
cpu2: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu2: 512KB 64b/line 16-way L2 cache
cpu3 at mainbus0 mpidr 101: ARM Cortex-A72 r0p1
cpu3: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu3: 512KB 64b/line 16-way L2 cache
cdce0 at uhub2 port 2 configuration 2 interface 0 "TP-LINK USB 10/100/1000 LAN" rev 2.10/30.00 addr 2
cdce0: address f4:f2:6d:18:1a:e2
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on sd0a (8b9b61adc6331423.a) swap on sd0b dump on sd0b
initializing kernel modesetting (CAICOS 0x1002:0x677B 0x1043:0x3025 0x00).
radeondrm0: 1920x1080, 32bpp
wsdisplay0 at radeondrm0 mux 1
wsdisplay0: screen 0-5 added (std, vt100 emulation)
the
"framebuffer" at mainbus0 not configured
line comes up because radeondrm(4) takes over and kicks out the UEFI
framebuffer. If I disable radeondrm(4) I get:
...
pci0 at acpipci0
0:0:0: mem address conflict 0xfffe0000/0x20000
"ATI Radeon HD 7450" rev 0x00 at pci0 dev 0 function 0 not configured
"ATI Radeon HD 6400 Audio" rev 0x00 at pci0 dev 0 function 1 not configured
simplefb0 at mainbus0: 800x600, 32bpp
wsdisplay0 at simplefb0 mux 1
wsdisplay0: screen 0-5 added (std, vt100 emulation)
...
instead.
This is a Radeon R5 230 card; here is some basic PCI info:
Domain /dev/pci0:
0:0:0: ATI Radeon HD 7450
0x0000: Vendor ID: 1002, Product ID: 677b
0x0004: Command: 0007, Status: 0010
0x0008: Class: 03 Display, Subclass: 00 VGA,
Interface: 00, Revision: 00
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR mem prefetchable 64bit addr: 0x0000000800000000/0x10000000
0x0018: BAR mem 64bit addr: 0x0000000810000000/0x00020000
0x0020: BAR io addr: 0x00000000/0x0100
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 1043 Product ID: 3025
0x0030: Expansion ROM Base Address: c0000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0050: Capability 0x01: Power Management
State: D0
0x0058: Capability 0x10: PCI Express
Link Speed: 5.0 / 5.0 GT/s, Link Width: x4 / x16
0x0100: Enhanced Capability 0x0b: Vendor-Specific
0x0150: Enhanced Capability 0x01: Advanced Error Reporting
0x00a0: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0:0:1: ATI Radeon HD 6400 Audio
0x0000: Vendor ID: 1002, Product ID: aa98
0x0004: Command: 0000, Status: 0010
0x0008: Class: 04 (unknown), Subclass: 03 (unknown),
Interface: 00, Revision: 00
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR mem 64bit addr: 0x0000000810020000/0x00004000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 1043 Product ID: aa98
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 02 Line: ff Min Gnt: 00 Max Lat: 00
0x0050: Capability 0x01: Power Management
State: D0
0x0058: Capability 0x10: PCI Express
Link Speed: 5.0 / 5.0 GT/s, Link Width: x4 / x16
0x0100: Enhanced Capability 0x0b: Vendor-Specific
0x0150: Enhanced Capability 0x01: Advanced Error Reporting
0x00a0: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
X11 works to some extent, but there are artifacts. Half the
characters in my xterms are missing, and there are some random
characters in places where they shouldn't be. That may very well be
an OpenBSD issue though. Strangely enough 3D acceleration seems to
work fine.
Cheers,
Mark
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support
2019-05-24 22:16 ` mark.kettenis
@ 2019-05-25 9:47 ` Ard Biesheuvel
0 siblings, 0 replies; 34+ messages in thread
From: Ard Biesheuvel @ 2019-05-25 9:47 UTC (permalink / raw)
To: Mark Kettenis
Cc: Leif Lindholm, Marcin Wojtas, edk2-devel-groups-io,
Jan Dąbroś, Grzegorz Jaszczyk, Kostya Porotchkin,
Jici Gao, Rebecca Cran, kettenis
On Sat, 25 May 2019 at 00:16, Mark Kettenis <mark.kettenis@xs4all.nl> wrote:
>
> > From: Ard Biesheuvel <ard.biesheuvel@linaro.org>
> > Date: Thu, 23 May 2019 19:13:20 +0100
> > Cc: Leif Lindholm <leif.lindholm@linaro.org>, Marcin Wojtas <mw@semihalf.com>,
> > edk2-devel-groups-io <devel@edk2.groups.io>,
> > Jan Dąbroś <jsd@semihalf.com>,
> > Grzegorz Jaszczyk <jaz@semihalf.com>,
> > Kostya Porotchkin <kostap@marvell.com>, Jici Gao <Jici.Gao@arm.com>,
> > Rebecca Cran <rebecca@bluestop.org>, kettenis@openbsd.org
> > Content-Type: text/plain; charset="UTF-8"
> >
> > On Thu, 23 May 2019 at 19:02, Mark Kettenis <kettenis@jive.eu> wrote:
> > >
> > > > Date: Thu, 23 May 2019 15:14:27 +0100
> > > > From: Leif Lindholm <leif.lindholm@linaro.org>
> > > >
> > > > On Thu, May 23, 2019 at 03:27:47PM +0200, Mark Kettenis wrote:
> > > > > > From: Marcin Wojtas <mw@semihalf.com>
> > > > > > Date: Mon, 20 May 2019 17:27:13 +0200
> > > > > >
> > > > > > Hi,
> > > > > >
> > > > > > Thank you for thorough review of v1. I submit second
> > > > > > version of the Armada7k8k PCIE support. I addressed
> > > > > > all comments. There is no functional change to initial
> > > > > > patchset, but mostly clean-up and improvements - please
> > > > > > refer to the changelog below.
> > > > > >
> > > > > > The patches are available in the github:
> > > > > > https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/commits/pcie-upstream-r20190520
> > > > > >
> > > > > > I'm looking forward to your comments or remarks.
> > > > > >
> > > > > > Best regards,
> > > > > > Marcin
> > > > >
> > > > > Tested this on my mcbin running OpenBSD. It incovers a small issue in
> > > > > our kernel which I'm fixing. Otherwise this seems to work fine.
> > > > >
> > > > > So tested-by: Mark Kettenis <kettenis@openbsd.org> if that matters.
> > > >
> > > > Always helpful, thanks.
> > > >
> > > > Out of interest, what was the issue?
> > > > Could I still expect the 6.5 installer to run on this
> > > > hardware/firmware combo?
> > >
> > > That should still work fine.
> > >
> > > The issue is with mapping PCI ROMS, which currently fails with the new
> > > firmware due to an oversight in the OpenBSD code. There are only a
> > > few OpenBSD drivers that attempt to map the PCI ROM. But one of those
> > > is radeondrm(4) and I stuck an AMD graphics card into the PCIe slot on
> > > my machine.
> > >
> > > There is a bit of a firmware angle to this though. The issue happens
> > > because the PCI ROM address register has been set to 0xfffe0000. All
> > > the writable address bits in the register are set to 1. While it is
> > > possible that the hardware comes up in that state, I suspect this is
> > > done by an attempt by the firmware to determine the size of the ROM
> > > that doesn't properly restore the original contents of the register.
> >
> > UEFI deliberately leaves the ROM BARs unassigned, in order to avoid
> > wasting valuable 32-bit PCI MMIO space. It enables the BAR temporarily
> > to load the ROM, and dispatches it if it can. After that, it changes
> > the BAR back to the old unassigned value.
>
> It seems that that last bit isn't working...
>
> > > It may be related to the following messages that are printed by the
> > > firmware:
> > >
> > > Image type X64 can't be loaded on AARCH64 UEFI system.
> > > Unloading driver at 0x00000000000
> >
> > That address value is quite unexpected.
> >
> > > Connect: PcieRoot(0x0)/Pci(0x0,0x0): Not Found
> > >
> > > Hmm, that's actually interesting. Maybe I should play with the X86
> > > emulator that Ard added recently to see if that gives me a framebuffer
> > > console.
> > >
> >
> > Yes, if you add edk2-staging to your PACKAGES_PATH env variable, all
> > you need to do is add -D X64EMU_ENABLE to the build command line.
> >
> > If you do end up testing this, could you please report back with the
> > result, i.e., the type of card, PCI PID/VID and whether it all worked
> > as expected? Thanks.
>
> Seems to work fine. The EFI shell and OpenBSD bootloader prompt show
> up on both the framebuffer and the serial console.
Thanks for the report.
...
> X11 works to some extent, but there are artifacts. Half the
> characters in my xterms are missing, and there are some random
> characters in places where they shouldn't be. That may very well be
> an OpenBSD issue though. Strangely enough 3D acceleration seems to
> work fine.
>
This smells like a DMA coherency issue. I recently disabled an
optimization in the linux version of the radeon/amdgpu drivers that
resulted in similar issues:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e02f5c1bb2283cfcee68f2f0feddcc06150f13aa
^ permalink raw reply [flat|nested] 34+ messages in thread
end of thread, other threads:[~2019-05-25 9:48 UTC | newest]
Thread overview: 34+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2019-05-20 15:27 [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 01/14] Marvell/Library: MvGpioLib: Extend GPIO pin description Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 02/14] Marvell/Library: ArmadaSoCDescLib: Add PCIE information Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 03/14] Marvell/Library: ArmadaBoardDescLib: " Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 04/14] Marvell/Armada7k8k: Extend board description libraries with PCIE Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 05/14] Marvell/Armada7k8k: MvBoardDesc: Extend protocol with PCIE support Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 06/14] Marvell/Armada7k8k: Add PciExpressLib implementation Marcin Wojtas
2019-05-24 12:50 ` Ard Biesheuvel
2019-05-24 13:03 ` Marcin Wojtas
2019-05-24 13:08 ` Ard Biesheuvel
2019-05-24 14:28 ` Marcin Wojtas
2019-05-24 15:25 ` Ard Biesheuvel
2019-05-24 15:32 ` Leif Lindholm
2019-05-24 15:43 ` Marcin Wojtas
2019-05-24 15:46 ` Ard Biesheuvel
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 07/14] Marvell/Armada7k8k: Implement PciHostBridgeLib Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 08/14] Marvell/Armada7k8k: Enable PCIE support Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 09/14] Marvell/Armada80x0McBin: Enable ACPI " Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 10/14] Marvell/Armada80x0Db: " Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 11/14] Marvell/Armada70x0Db: " Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 12/14] Marvell/Armada80x0McBin: DeviceTree: Use pci-host-generic driver Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 13/14] Marvell/Armada7k8k: Remove duplication in .dsc files Marcin Wojtas
2019-05-20 15:27 ` [edk2-platforms: PATCH v2 14/14] Marvell/Armada7k8: Add 'acpiview' shell command to build Marcin Wojtas
2019-05-23 13:27 ` [edk2-platforms: PATCH v2 00/14] Armada7k8k PCIE support Mark Kettenis
2019-05-23 14:14 ` Leif Lindholm
2019-05-23 18:01 ` kettenis
2019-05-23 18:13 ` Ard Biesheuvel
2019-05-23 20:11 ` Leif Lindholm
2019-05-23 20:24 ` Ard Biesheuvel
2019-05-24 13:08 ` Marcin Wojtas
2019-05-24 13:12 ` Ard Biesheuvel
2019-05-24 13:13 ` Marcin Wojtas
2019-05-24 22:16 ` mark.kettenis
2019-05-25 9:47 ` Ard Biesheuvel
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox