From: Ard Biesheuvel <ard.biesheuvel@linaro.org>
To: edk2-devel@lists.01.org
Cc: leif.lindholm@linaro.org, Ard Biesheuvel <ard.biesheuvel@linaro.org>
Subject: [PATCH v2 10/13] ArmPlatformPkg: remove PL34xDmc driver
Date: Mon, 4 Dec 2017 22:22:40 +0000 [thread overview]
Message-ID: <20171204222243.15950-11-ard.biesheuvel@linaro.org> (raw)
In-Reply-To: <20171204222243.15950-1-ard.biesheuvel@linaro.org>
Remove PL34xDmc driver which is not used by any platforms
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by-if-no-comments-by-15-Dec: Leif Lindholm <leif.lindholm@linaro.org>
---
ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.c | 227 -------------
ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.inf | 29 --
ArmPlatformPkg/Include/Drivers/PL341Dmc.h | 336 --------------------
3 files changed, 592 deletions(-)
diff --git a/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.c b/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.c
deleted file mode 100644
index 08eba6ec6930..000000000000
--- a/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.c
+++ /dev/null
@@ -1,227 +0,0 @@
-/** @file
-*
-* Copyright (c) 2011, ARM Limited. All rights reserved.
-*
-* This program and the accompanying materials
-* are licensed and made available under the terms and conditions of the BSD License
-* which accompanies this distribution. The full text of the license may be found at
-* http://opensource.org/licenses/bsd-license.php
-*
-* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
-* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
-*
-**/
-
-#include <Uefi.h>
-
-#include <Library/IoLib.h>
-#include <Library/DebugLib.h>
-
-#include <Drivers/PL341Dmc.h>
-
-// Macros for writing to DDR2 controller.
-#define DmcWriteReg(reg,val) MmioWrite32(DmcBase + reg, val)
-#define DmcReadReg(reg) MmioRead32(DmcBase + reg)
-
-// Macros for writing/reading to DDR2 PHY controller
-#define DmcPhyWriteReg(reg,val) MmioWrite32(DmcPhyBase + reg, val)
-#define DmcPhyReadReg(reg) MmioRead32(DmcPhyBase + reg)
-
-// Initialise PL341 Dynamic Memory Controller
-VOID
-PL341DmcInit (
- IN UINTN DmcBase,
- IN PL341_DMC_CONFIG* DmcConfig
- )
-{
- UINTN Index;
- UINT32 Chip;
-
- // Set config mode
- DmcWriteReg(DMC_COMMAND_REG, DMC_COMMAND_CONFIGURE);
-
- //
- // Setup the QoS AXI ID bits
- //
- if (DmcConfig->HasQos) {
- // CLCD AXIID = 000
- DmcWriteReg(DMC_ID_0_CFG_REG, DMC_ID_CFG_QOS_ENABLE | DMC_ID_CFG_QOS_MIN);
-
- // Default disable QoS
- DmcWriteReg(DMC_ID_1_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_2_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_3_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_4_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_5_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_6_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_7_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_8_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_9_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_10_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_11_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_12_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_13_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_14_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- DmcWriteReg(DMC_ID_15_CFG_REG, DMC_ID_CFG_QOS_DISABLE);
- }
-
- //
- // Initialise memory controlller
- //
- DmcWriteReg(DMC_REFRESH_PRD_REG, DmcConfig->RefreshPeriod);
- DmcWriteReg(DMC_CAS_LATENCY_REG, DmcConfig->CasLatency);
- DmcWriteReg(DMC_WRITE_LATENCY_REG, DmcConfig->WriteLatency);
- DmcWriteReg(DMC_T_MRD_REG, DmcConfig->t_mrd);
- DmcWriteReg(DMC_T_RAS_REG, DmcConfig->t_ras);
- DmcWriteReg(DMC_T_RC_REG, DmcConfig->t_rc);
- DmcWriteReg(DMC_T_RCD_REG, DmcConfig->t_rcd);
- DmcWriteReg(DMC_T_RFC_REG, DmcConfig->t_rfc);
- DmcWriteReg(DMC_T_RP_REG, DmcConfig->t_rp);
- DmcWriteReg(DMC_T_RRD_REG, DmcConfig->t_rrd);
- DmcWriteReg(DMC_T_WR_REG, DmcConfig->t_wr);
- DmcWriteReg(DMC_T_WTR_REG, DmcConfig->t_wtr);
- DmcWriteReg(DMC_T_XP_REG, DmcConfig->t_xp);
- DmcWriteReg(DMC_T_XSR_REG, DmcConfig->t_xsr);
- DmcWriteReg(DMC_T_ESR_REG, DmcConfig->t_esr);
- DmcWriteReg(DMC_T_FAW_REG, DmcConfig->t_faw);
- DmcWriteReg(DMC_T_WRLAT_DIFF, DmcConfig->t_wdata_en);
- DmcWriteReg(DMC_T_RDATA_EN, DmcConfig->t_data_en);
-
- //
- // Initialise PL341 Mem Config Registers
- //
-
- // Set PL341 Memory Config
- DmcWriteReg(DMC_MEMORY_CONFIG_REG, DmcConfig->MemoryCfg);
-
- // Set PL341 Memory Config 2
- DmcWriteReg(DMC_MEMORY_CFG2_REG, DmcConfig->MemoryCfg2);
-
- // Set PL341 Memory Config 3
- DmcWriteReg(DMC_MEMORY_CFG3_REG, DmcConfig->MemoryCfg3);
-
- // Set PL341 Chip Select <n>
- DmcWriteReg(DMC_CHIP_0_CFG_REG, DmcConfig->ChipCfg0);
- DmcWriteReg(DMC_CHIP_1_CFG_REG, DmcConfig->ChipCfg1);
- DmcWriteReg(DMC_CHIP_2_CFG_REG, DmcConfig->ChipCfg2);
- DmcWriteReg(DMC_CHIP_3_CFG_REG, DmcConfig->ChipCfg3);
-
- // Delay
- for (Index = 0; Index < 10; Index++) {
- DmcReadReg(DMC_STATUS_REG);
- }
-
- if (DmcConfig->IsUserCfg) {
- //
- // Set Test Chip PHY Registers via PL341 User Config Reg
- // Note that user_cfgX registers are Write Only
- //
- // DLL Freq set = 250MHz - 266MHz
- //
- DmcWriteReg(DMC_USER_0_CFG_REG, DmcConfig->User0Cfg);
-
- // user_config2
- // ------------
- // Set defaults before calibrating the DDR2 buffer impendence
- // - Disable ODT
- // - Default drive strengths
- DmcWriteReg(DMC_USER_2_CFG_REG, 0x40000198);
-
- //
- // Auto calibrate the DDR2 buffers impendence
- //
- while (!(DmcReadReg(DMC_USER_STATUS_REG) & 0x100));
-
- // Set the output driven strength
- DmcWriteReg(DMC_USER_2_CFG_REG, 0x40800000 | DmcConfig->User2Cfg);
-
- //
- // Set PL341 Feature Control Register
- //
- // Disable early BRESP - use to optimise CLCD performance
- DmcWriteReg(DMC_FEATURE_CRTL_REG, 0x00000001);
- }
-
- //
- // Config memories
- //
- for (Chip = 0; Chip < DmcConfig->MaxChip; Chip++) {
- // Send nop
- DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_NOP);
-
- // Pre-charge all
- DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_PRECHARGEALL);
-
- // Delay
- for (Index = 0; Index < 10; Index++) {
- DmcReadReg(DMC_STATUS_REG);
- }
-
- // Set (EMR2) extended mode register 2
- DmcWriteReg(DMC_DIRECT_CMD_REG,
- DMC_DIRECT_CMD_CHIP_ADDR(Chip) |
- DMC_DIRECT_CMD_BANKADDR(2) |
- DMC_DIRECT_CMD_MEMCMD_EXTMODEREG);
-
- // Set (EMR3) extended mode register 3
- DmcWriteReg(DMC_DIRECT_CMD_REG,
- DMC_DIRECT_CMD_CHIP_ADDR(Chip) |
- DMC_DIRECT_CMD_BANKADDR(3) |
- DMC_DIRECT_CMD_MEMCMD_EXTMODEREG);
-
- //
- // Set (EMR) Extended Mode Register
- //
- // Put into OCD default state
- DmcWriteReg(DMC_DIRECT_CMD_REG,DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_BANKADDR(1) | DMC_DIRECT_CMD_MEMCMD_EXTMODEREG);
-
- //
- // Set (MR) mode register - With DLL reset
- //
- DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_EXTMODEREG | DmcConfig->ModeReg | DDR2_MR_DLL_RESET);
-
- // Pre-charge all
- DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_PRECHARGEALL);
- // Auto-refresh
- DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_AUTOREFRESH);
- // Auto-refresh
- DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_AUTOREFRESH);
-
- //
- // Set (MR) mode register - Without DLL reset
- //
- DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | DMC_DIRECT_CMD_MEMCMD_EXTMODEREG | DmcConfig->ModeReg);
-
- // Delay
- for (Index = 0; Index < 10; Index++) {
- DmcReadReg(DMC_STATUS_REG);
- }
-
- //
- // Set (EMR) extended mode register - Enable OCD defaults
- //
- DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | (0x00090000) |
- (1 << DDR_MODESET_SHFT) | (DDR_EMR_OCD_DEFAULT << DDR_EMR_OCD_SHIFT) | DmcConfig->ExtModeReg);
-
- // Delay
- for (Index = 0; Index < 10; Index++) {
- DmcReadReg(DMC_STATUS_REG);
- }
-
- // Set (EMR) extended mode register - OCD Exit
- DmcWriteReg(DMC_DIRECT_CMD_REG, DMC_DIRECT_CMD_CHIP_ADDR(Chip) | (0x00090000) |
- (1 << DDR_MODESET_SHFT) | (DDR_EMR_OCD_NS << DDR_EMR_OCD_SHIFT) | DmcConfig->ExtModeReg);
-
- // Delay
- for (Index = 0; Index < 10; Index++) {
- DmcReadReg(DMC_STATUS_REG);
- }
- }
-
- // Move DDR2 Controller to Ready state by issueing GO command
- DmcWriteReg(DMC_COMMAND_REG, DMC_COMMAND_GO);
-
- // wait for ready
- while (!(DmcReadReg(DMC_STATUS_REG) & DMC_STATUS_READY));
-
-}
diff --git a/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.inf b/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.inf
deleted file mode 100644
index 0f3d862e14ef..000000000000
--- a/ArmPlatformPkg/Drivers/PL34xDmc/PL341Dmc.inf
+++ /dev/null
@@ -1,29 +0,0 @@
-#/* @file
-# Copyright (c) 2011, ARM Limited. All rights reserved.
-#
-# This program and the accompanying materials
-# are licensed and made available under the terms and conditions of the BSD License
-# which accompanies this distribution. The full text of the license may be found at
-# http://opensource.org/licenses/bsd-license.php
-#
-# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
-# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
-#
-#*/
-
-[Defines]
- INF_VERSION = 0x00010005
- BASE_NAME = PL341Dmc
- FILE_GUID = edf8da40-aad1-11df-a1f4-0002a5d5c51b
- MODULE_TYPE = BASE
- VERSION_STRING = 1.0
- LIBRARY_CLASS = PL341DmcLib
-
-[Sources]
- PL341Dmc.c
-
-[Packages]
- ArmPlatformPkg/ArmPlatformPkg.dec
- MdePkg/MdePkg.dec
-
-[FixedPcd]
diff --git a/ArmPlatformPkg/Include/Drivers/PL341Dmc.h b/ArmPlatformPkg/Include/Drivers/PL341Dmc.h
deleted file mode 100644
index caba8f445bd8..000000000000
--- a/ArmPlatformPkg/Include/Drivers/PL341Dmc.h
+++ /dev/null
@@ -1,336 +0,0 @@
-/** @file
-*
-* Copyright (c) 2011, ARM Limited. All rights reserved.
-*
-* This program and the accompanying materials
-* are licensed and made available under the terms and conditions of the BSD License
-* which accompanies this distribution. The full text of the license may be found at
-* http://opensource.org/licenses/bsd-license.php
-*
-* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
-* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
-*
-**/
-
-#ifndef _PL341DMC_H_
-#define _PL341DMC_H_
-
-
-typedef struct {
- UINTN HasQos; // has QoS registers
- UINTN MaxChip; // number of memory chips accessible
- BOOLEAN IsUserCfg;
- UINT32 User0Cfg;
- UINT32 User2Cfg;
- UINT32 RefreshPeriod;
- UINT32 CasLatency;
- UINT32 WriteLatency;
- UINT32 t_mrd;
- UINT32 t_ras;
- UINT32 t_rc;
- UINT32 t_rcd;
- UINT32 t_rfc;
- UINT32 t_rp;
- UINT32 t_rrd;
- UINT32 t_wr;
- UINT32 t_wtr;
- UINT32 t_xp;
- UINT32 t_xsr;
- UINT32 t_esr;
- UINT32 MemoryCfg;
- UINT32 MemoryCfg2;
- UINT32 MemoryCfg3;
- UINT32 ChipCfg0;
- UINT32 ChipCfg1;
- UINT32 ChipCfg2;
- UINT32 ChipCfg3;
- UINT32 t_faw;
- UINT32 t_data_en;
- UINT32 t_wdata_en;
- UINT32 ModeReg;
- UINT32 ExtModeReg;
-} PL341_DMC_CONFIG;
-
-/* Memory config bit fields */
-#define DMC_MEMORY_CONFIG_COLUMN_ADDRESS_9 0x1
-#define DMC_MEMORY_CONFIG_COLUMN_ADDRESS_10 0x2
-#define DMC_MEMORY_CONFIG_COLUMN_ADDRESS_11 0x3
-#define DMC_MEMORY_CONFIG_COLUMN_ADDRESS_12 0x4
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_11 (0x0 << 3)
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_12 (0x1 << 3)
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_13 (0x2 << 3)
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_14 (0x3 << 3)
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_15 (0x4 << 3)
-#define DMC_MEMORY_CONFIG_ROW_ADDRESS_16 (0x5 << 3)
-#define DMC_MEMORY_CONFIG_BURST_2 (0x1 << 15)
-#define DMC_MEMORY_CONFIG_BURST_4 (0x2 << 15)
-#define DMC_MEMORY_CONFIG_BURST_8 (0x3 << 15)
-#define DMC_MEMORY_CONFIG_BURST_16 (0x4 << 15)
-#define DMC_MEMORY_CONFIG_ACTIVE_CHIP_1 (0x0 << 21)
-#define DMC_MEMORY_CONFIG_ACTIVE_CHIP_2 (0x1 << 21)
-#define DMC_MEMORY_CONFIG_ACTIVE_CHIP_3 (0x2 << 21)
-#define DMC_MEMORY_CONFIG_ACTIVE_CHIP_4 (0x3 << 21)
-
-#define DMC_MEMORY_CFG2_CLK_ASYNC (0x0 << 0)
-#define DMC_MEMORY_CFG2_CLK_SYNC (0x1 << 0)
-#define DMC_MEMORY_CFG2_DQM_INIT (0x1 << 2)
-#define DMC_MEMORY_CFG2_CKE_INIT (0x1 << 3)
-#define DMC_MEMORY_CFG2_BANK_BITS_2 (0x0 << 4)
-#define DMC_MEMORY_CFG2_BANK_BITS_3 (0x3 << 4)
-#define DMC_MEMORY_CFG2_MEM_WIDTH_16 (0x0 << 6)
-#define DMC_MEMORY_CFG2_MEM_WIDTH_32 (0x1 << 6)
-#define DMC_MEMORY_CFG2_MEM_WIDTH_64 (0x2 << 6)
-#define DMC_MEMORY_CFG2_MEM_WIDTH_RESERVED (0x3 << 6)
-
-//
-// DMC Configuration Register Map
-//
-#define DMC_STATUS_REG 0x00
-#define DMC_COMMAND_REG 0x04
-#define DMC_DIRECT_CMD_REG 0x08
-#define DMC_MEMORY_CONFIG_REG 0x0C
-#define DMC_REFRESH_PRD_REG 0x10
-#define DMC_CAS_LATENCY_REG 0x14
-#define DMC_WRITE_LATENCY_REG 0x18
-#define DMC_T_MRD_REG 0x1C
-#define DMC_T_RAS_REG 0x20
-#define DMC_T_RC_REG 0x24
-#define DMC_T_RCD_REG 0x28
-#define DMC_T_RFC_REG 0x2C
-#define DMC_T_RP_REG 0x30
-#define DMC_T_RRD_REG 0x34
-#define DMC_T_WR_REG 0x38
-#define DMC_T_WTR_REG 0x3C
-#define DMC_T_XP_REG 0x40
-#define DMC_T_XSR_REG 0x44
-#define DMC_T_ESR_REG 0x48
-#define DMC_MEMORY_CFG2_REG 0x4C
-#define DMC_MEMORY_CFG3_REG 0x50
-#define DMC_T_FAW_REG 0x54
-#define DMC_T_RDATA_EN 0x5C /* DFI read data enable register */
-#define DMC_T_WRLAT_DIFF 0x60 /* DFI write data enable register */
-
-// Returns the state of the memory controller:
-#define DMC_STATUS_CONFIG 0x0
-#define DMC_STATUS_READY 0x1
-#define DMC_STATUS_PAUSED 0x2
-#define DMC_STATUS_LOWPOWER 0x3
-
-// Changes the state of the memory controller:
-#define DMC_COMMAND_GO 0x0
-#define DMC_COMMAND_SLEEP 0x1
-#define DMC_COMMAND_WAKEUP 0x2
-#define DMC_COMMAND_PAUSE 0x3
-#define DMC_COMMAND_CONFIGURE 0x4
-#define DMC_COMMAND_ACTIVEPAUSE 0x7
-
-// Determines the command required
-#define DMC_DIRECT_CMD_MEMCMD_PRECHARGEALL 0x0
-#define DMC_DIRECT_CMD_MEMCMD_AUTOREFRESH (0x1 << 18)
-#define DMC_DIRECT_CMD_MEMCMD_MODEREG (0x2 << 18)
-#define DMC_DIRECT_CMD_MEMCMD_EXTMODEREG (0x2 << 18)
-#define DMC_DIRECT_CMD_MEMCMD_NOP (0x3 << 18)
-#define DMC_DIRECT_CMD_MEMCMD_DPD (0x1 << 22)
-#define DMC_DIRECT_CMD_BANKADDR(n) ((n & 0x3) << 16)
-#define DMC_DIRECT_CMD_CHIP_ADDR(n) ((n & 0x3) << 20)
-
-
-//
-// AXI ID configuration register map
-//
-#define DMC_ID_0_CFG_REG 0x100
-#define DMC_ID_1_CFG_REG 0x104
-#define DMC_ID_2_CFG_REG 0x108
-#define DMC_ID_3_CFG_REG 0x10C
-#define DMC_ID_4_CFG_REG 0x110
-#define DMC_ID_5_CFG_REG 0x114
-#define DMC_ID_6_CFG_REG 0x118
-#define DMC_ID_7_CFG_REG 0x11C
-#define DMC_ID_8_CFG_REG 0x120
-#define DMC_ID_9_CFG_REG 0x124
-#define DMC_ID_10_CFG_REG 0x128
-#define DMC_ID_11_CFG_REG 0x12C
-#define DMC_ID_12_CFG_REG 0x130
-#define DMC_ID_13_CFG_REG 0x134
-#define DMC_ID_14_CFG_REG 0x138
-#define DMC_ID_15_CFG_REG 0x13C
-
-// Set the QoS
-#define DMC_ID_CFG_QOS_DISABLE 0
-#define DMC_ID_CFG_QOS_ENABLE 1
-#define DMC_ID_CFG_QOS_MIN 2
-
-
-//
-// Chip configuration register map
-//
-#define DMC_CHIP_0_CFG_REG 0x200
-#define DMC_CHIP_1_CFG_REG 0x204
-#define DMC_CHIP_2_CFG_REG 0x208
-#define DMC_CHIP_3_CFG_REG 0x20C
-
-//
-// User Defined Pins
-//
-#define DMC_USER_STATUS_REG 0x300
-#define DMC_USER_0_CFG_REG 0x304
-#define DMC_USER_1_CFG_REG 0x308
-#define DMC_FEATURE_CRTL_REG 0x30C
-#define DMC_USER_2_CFG_REG 0x310
-
-
-//
-// PHY Register Settings
-//
-#define PHY_PTM_DFI_CLK_RANGE 0xE00 // DDR2 PHY PTM register offset
-#define PHY_PTM_IOTERM 0xE04
-#define PHY_PTM_PLL_EN 0xe0c
-#define PHY_PTM_PLL_RANGE 0xe18
-#define PHY_PTM_FEEBACK_DIV 0xe1c
-#define PHY_PTM_RCLK_DIV 0xe20
-#define PHY_PTM_LOCK_STATUS 0xe28
-#define PHY_PTM_INIT_DONE 0xe34
-#define PHY_PTM_ADDCOM_IOSTR_OFF 0xec8
-#define PHY_PTM_SQU_TRAINING 0xee8
-#define PHY_PTM_SQU_STAT 0xeec
-
-// ==============================================================================
-// PIPD 40G DDR2/DDR3 PHY Register definitions
-//
-// Offsets from APB Base Address
-// ==============================================================================
-#define PHY_BYTE0_OFFSET 0x000
-#define PHY_BYTE1_OFFSET 0x200
-#define PHY_BYTE2_OFFSET 0x400
-#define PHY_BYTE3_OFFSET 0x600
-
-#define PHY_BYTE0_COARSE_SQADJ_INIT 0x064 ;// Coarse squelch adjust
-#define PHY_BYTE1_COARSE_SQADJ_INIT 0x264 ;// Coarse squelch adjust
-#define PHY_BYTE2_COARSE_SQADJ_INIT 0x464 ;// Coarse squelch adjust
-#define PHY_BYTE3_COARSE_SQADJ_INIT 0x664 ;// Coarse squelch adjust
-
-#define PHY_BYTE0_IOSTR_OFFSET 0x004
-#define PHY_BYTE1_IOSTR_OFFSET 0x204
-#define PHY_BYTE2_IOSTR_OFFSET 0x404
-#define PHY_BYTE3_IOSTR_OFFSET 0x604
-
-
-;//--------------------------------------------------------------------------
-
-// DFI Clock ranges:
-
-#define PHY_PTM_DFI_CLK_RANGE_200MHz 0x0
-#define PHY_PTM_DFI_CLK_RANGE_201_267MHz 0x1
-#define PHY_PTM_DFI_CLK_RANGE_268_333MHz 0x2
-#define PHY_PTM_DFI_CLK_RANGE_334_400MHz 0x3
-#define PHY_PTM_DFI_CLK_RANGE_401_533MHz 0x4
-#define PHY_PTM_DFI_CLK_RANGE_534_667MHz 0x5
-#define PHY_PTM_DFI_CLK_RANGE_668_800MHz 0x6
-
-
-
-#define PHY_PTM_DFI_CLK_RANGE_VAL PHY_PTM_DFI_CLK_RANGE_334_400MHz
-
-//--------------------------------------------------------------------------
-
-
-// PLL Range
-
-#define PHY_PTM_PLL_RANGE_200_400MHz 0x0 // b0 = frequency >= 200 MHz and < 400 MHz
-#define PHY_PTM_PLL_RANGE_400_800MHz 0x1 // b1 = frequency >= 400 MHz.
-#define PHY_PTM_FEEBACK_DIV_200_400MHz 0x0 // b0 = frequency >= 200 MHz and < 400 MHz
-#define PHY_PTM_FEEBACK_DIV_400_800MHz 0x1 // b1 = frequency >= 400 MHz.
-#define PHY_PTM_REFCLK_DIV_200_400MHz 0x0
-#define PHY_PTM_REFCLK_DIV_400_800MHz 0x1
-
-#define TC_UIOLHNC_MASK 0x000003C0
-#define TC_UIOLHNC_SHIFT 0x6
-#define TC_UIOLHPC_MASK 0x0000003F
-#define TC_UIOLHPC_SHIFT 0x2
-#define TC_UIOHOCT_MASK 0x2
-#define TC_UIOHOCT_SHIFT 0x1
-#define TC_UIOHSTOP_SHIFT 0x0
-#define TC_UIOLHXC_VALUE 0x4
-
-#define PHY_PTM_SQU_TRAINING_ENABLE 0x1
-#define PHY_PTM_SQU_TRAINING_DISABLE 0x0
-
-
-//--------------------------------------
-// JEDEC DDR2 Device Register definitions and settings
-//--------------------------------------
-#define DDR_MODESET_SHFT 14
-#define DDR_MODESET_MR 0x0 ;// Mode register
-#define DDR_MODESET_EMR 0x1 ;// Extended Mode register
-#define DDR_MODESET_EMR2 0x2
-#define DDR_MODESET_EMR3 0x3
-
-//
-// Extended Mode Register settings
-//
-#define DDR_EMR_OCD_MASK 0x0000380
-#define DDR_EMR_OCD_SHIFT 0x7
-#define DDR_EMR_RTT_MASK 0x00000044 // DDR2 Device RTT (ODT) settings
-#define DDR_EMR_RTT_SHIFT 0x2
-#define DDR_EMR_ODS_MASK 0x00000002 // DDR2 Output Drive Strength
-#define DDR_EMR_ODS_SHIFT 0x0001
-
-// Termination Values:
-#define DDR_EMR_RTT_50R 0x00000044 // DDR2 50 Ohm termination
-#define DDR_EMR_RTT_75R 0x00000004 // DDR2 75 Ohm termination
-#define DDR_EMR_RTT_150 0x00000040 // DDR2 150 Ohm termination
-
-// Output Drive Strength Values:
-#define DDR_EMR_ODS_FULL 0x0 // DDR2 Full Drive Strength
-#define DDR_EMR_ODS_HALF 0x1 // DDR2 Half Drive Strength
-
-// OCD values
-#define DDR_EMR_OCD_DEFAULT 0x7
-#define DDR_EMR_OCD_NS 0x0
-
-#define DDR_EMR_ODS_VAL DDR_EMR_ODS_FULL
-
-#define DDR_SDRAM_START_ADDR 0x10000000
-
-
-// ----------------------------------------
-// PHY IOTERM values
-// ----------------------------------------
-#define PHY_PTM_IOTERM_OFF 0x0
-#define PHY_PTM_IOTERM_150R 0x1
-#define PHY_PTM_IOTERM_75R 0x2
-#define PHY_PTM_IOTERM_50R 0x3
-
-#define PHY_BYTE_IOSTR_60OHM 0x0
-#define PHY_BYTE_IOSTR_40OHM 0x1
-#define PHY_BYTE_IOSTR_30OHM 0x2
-#define PHY_BYTE_IOSTR_30AOHM 0x3
-
-#define DDR2_MR_BURST_LENGTH_4 (2)
-#define DDR2_MR_BURST_LENGTH_8 (3)
-#define DDR2_MR_DLL_RESET (1 << 8)
-#define DDR2_MR_CAS_LATENCY_4 (4 << 4)
-#define DDR2_MR_CAS_LATENCY_5 (5 << 4)
-#define DDR2_MR_CAS_LATENCY_6 (6 << 4)
-#define DDR2_MR_WR_CYCLES_2 (1 << 9)
-#define DDR2_MR_WR_CYCLES_3 (2 << 9)
-#define DDR2_MR_WR_CYCLES_4 (3 << 9)
-#define DDR2_MR_WR_CYCLES_5 (4 << 9)
-#define DDR2_MR_WR_CYCLES_6 (5 << 9)
-
-
-VOID
-PL341DmcInit (
- IN UINTN DmcBase,
- IN PL341_DMC_CONFIG* DmcConfig
- );
-
-VOID PL341DmcPhyInit (
- IN UINTN DmcPhyBase
- );
-
-VOID PL341DmcTrainPHY (
- IN UINTN DmcPhyBase
- );
-
-#endif /* _PL341DMC_H_ */
--
2.11.0
next prev parent reply other threads:[~2017-12-04 22:18 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-04 22:22 [PATCH v2 00/13] ArmPlatformPkg: remove unused or migrated modules Ard Biesheuvel
2017-12-04 22:22 ` [PATCH v2 01/13] ArmPlatformPkg: remove NorFlashArmVExpressLib Ard Biesheuvel
2017-12-04 22:22 ` [PATCH v2 02/13] ArmPlatformPkg: remove ArmVExpressPkg Ard Biesheuvel
2017-12-04 22:22 ` [PATCH v2 03/13] ArmPlatformPkg: remove ArmPlatformSysConfigLib library class Ard Biesheuvel
2017-12-04 22:22 ` [PATCH v2 04/13] ArmPlatformPkg: remove BootMonFs and ArmShellCmdRunAxf Ard Biesheuvel
2017-12-04 22:22 ` [PATCH v2 05/13] ArmPlatformPkg: remove old PL011UartLib implementation Ard Biesheuvel
2017-12-04 22:22 ` [PATCH v2 06/13] ArmPlatformPkg: add missing library class declarations to .dec file Ard Biesheuvel
2017-12-04 22:22 ` [PATCH v2 07/13] ArmPlatformPkg/LcdGraphicsOutputDxe: move headers into driver directory Ard Biesheuvel
2017-12-04 22:22 ` [PATCH v2 08/13] ArmPlatformPkg: remove unused PL301Axi driver Ard Biesheuvel
2017-12-04 22:22 ` [PATCH v2 09/13] ArmPlatformPkg: remove unused PL35x driver Ard Biesheuvel
2017-12-04 22:22 ` Ard Biesheuvel [this message]
2017-12-04 22:22 ` [PATCH v2 11/13] ArmPlatformPkg: remove unused PL310 driver Ard Biesheuvel
2017-12-04 22:22 ` [PATCH v2 12/13] ArmPlatformPkg: remove unused ArmTrustZone driver Ard Biesheuvel
2017-12-04 22:22 ` [PATCH v2 13/13] ArmPlatformPkg: remove unused SP804 driver and TimerLib implementation Ard Biesheuvel
2017-12-08 15:59 ` [PATCH v2 00/13] ArmPlatformPkg: remove unused or migrated modules Leif Lindholm
2017-12-08 16:35 ` Ard Biesheuvel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-list from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20171204222243.15950-11-ard.biesheuvel@linaro.org \
--to=devel@edk2.groups.io \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox