From: Leif Lindholm <leif.lindholm@linaro.org>
To: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: edk2-devel@lists.01.org
Subject: Re: [PATCH v2] Silicon/SynQuacer/PlatformDxe: enable spread spectrum mode for ASM1061 SATA
Date: Wed, 24 Jan 2018 12:02:22 +0000 [thread overview]
Message-ID: <20180124120222.yyaih5vnylacreg6@bivouac.eciton.net> (raw)
In-Reply-To: <20180124115711.18797-1-ard.biesheuvel@linaro.org>
On Wed, Jan 24, 2018 at 11:57:11AM +0000, Ard Biesheuvel wrote:
> The ASM1061 SATA controller integrated into the DeveloperBox board
> emits too much electromagnetic radiation, so it needs spread spectrum
> mode enabled.
>
> Contributed-under: TianoCore Contribution Agreement 1.1
> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
> ---
> v2: - rename AsmediaXXX.c to Pci.c
> - rename RegisterAsm1184Notifier() to RegisterPciIoNotifier() and make
> its invocation unconditional (rather than only if PCI domain #0 is
> not limited to Gen1 speed)
> - use switch() rather than if() in PID/VID check
Thanks!
>
> Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/{Asmedia118x.c => Pci.c} | 87 +++++++++++++++-----
> Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.c | 18 ++--
> Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.h | 5 +-
> Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.inf | 2 +-
> 4 files changed, 80 insertions(+), 32 deletions(-)
>
> diff --git a/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/Asmedia118x.c b/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/Pci.c
> similarity index 63%
> rename from Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/Asmedia118x.c
> rename to Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/Pci.c
> index c4cbacd3dff9..7ac96ab22b7a 100644
> --- a/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/Asmedia118x.c
> +++ b/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/Pci.c
> @@ -15,9 +15,12 @@
> #include "PlatformDxe.h"
>
> #define ASMEDIA_VID 0x1b21
> +#define ASM1061_PID 0x0612
> #define ASM1182E_PID 0x1182
> #define ASM1184E_PID 0x1184
>
> +#define ASM1061_SSC_OFFSET 0xA10
> +
> #define ASM118x_PCIE_CAPABILITY_OFFSET 0x80
> #define ASM118x_PCIE_LINK_CONTROL_OFFSET (ASM118x_PCIE_CAPABILITY_OFFSET + \
> OFFSET_OF (PCI_CAPABILITY_PCIEXP, \
> @@ -39,24 +42,10 @@ RetrainAsm1184eDownstreamPort (
> IN EFI_PCI_IO_PROTOCOL *PciIo
> )
> {
> - UINT16 PciVidPid[2];
> EFI_STATUS Status;
> PCIE_CAP Cap;
> PCI_REG_PCIE_LINK_CONTROL LinkControl;
>
> - Status = PciIo->Pci.Read (PciIo, EfiPciIoWidthUint16, PCI_VENDOR_ID_OFFSET,
> - ARRAY_SIZE (PciVidPid), &PciVidPid);
> - if (EFI_ERROR (Status)) {
> - DEBUG ((DEBUG_WARN, "%a: failed to read PCI vendor/product ID - %r\n",
> - __FUNCTION__, Status));
> - return;
> - }
> -
> - if (PciVidPid[0] != ASMEDIA_VID ||
> - (PciVidPid[1] != ASM1182E_PID && PciVidPid[1] != ASM1184E_PID)) {
> - return;
> - }
> -
> //
> // The upstream and downstream ports share the same PID/VID, so check
> // the port type. This assumes the PCIe Express capability block lives
> @@ -91,6 +80,34 @@ RetrainAsm1184eDownstreamPort (
>
> STATIC
> VOID
> +EnableAsm1061SpreadSpectrum (
> + IN EFI_PCI_IO_PROTOCOL *PciIo
> + )
> +{
> + EFI_STATUS Status;
> + UINT8 SscVal;
> +
> + DEBUG ((DEBUG_INFO, "%a: enabling spread spectrum mode 0 for ASM1061\n",
> + __FUNCTION__));
> +
> + // SSC mode 0~-4000 ppm, 1:1 modulation
> +
> + SscVal = 0;
> + Status = PciIo->Pci.Write (PciIo, EfiPciIoWidthUint8, ASM1061_SSC_OFFSET, 1,
> + &SscVal);
> + ASSERT_EFI_ERROR (Status);
> +
> + MemoryFence ();
> + gBS->Stall (1); // delay at least 100 ns between writes of the same register
> +
> + SscVal = 1;
> + Status = PciIo->Pci.Write (PciIo, EfiPciIoWidthUint8, ASM1061_SSC_OFFSET, 1,
> + &SscVal);
> + ASSERT_EFI_ERROR (Status);
> +}
> +
> +STATIC
> +VOID
> EFIAPI
> OnPciIoProtocolNotify (
> IN EFI_EVENT Event,
> @@ -101,6 +118,7 @@ OnPciIoProtocolNotify (
> EFI_STATUS Status;
> EFI_HANDLE HandleBuffer;
> UINTN BufferSize;
> + UINT16 PciVidPid[2];
>
> while (TRUE) {
> BufferSize = sizeof (EFI_HANDLE);
> @@ -114,18 +132,45 @@ OnPciIoProtocolNotify (
> (VOID **)&PciIo);
> ASSERT_EFI_ERROR (Status);
>
> - //
> - // The ASM1184E 4-port PCIe switch on the DeveloperBox board (and its
> - // 2-port sibling of which samples were used in development) needs a
> - // little nudge to get it to train the downstream links at Gen2 speed.
> - //
> - RetrainAsm1184eDownstreamPort (PciIo);
> + Status = PciIo->Pci.Read (PciIo, EfiPciIoWidthUint16, PCI_VENDOR_ID_OFFSET,
> + ARRAY_SIZE (PciVidPid), &PciVidPid);
> + if (EFI_ERROR (Status)) {
> + DEBUG ((DEBUG_WARN, "%a: failed to read PCI vendor/product ID - %r\n",
> + __FUNCTION__, Status));
> + continue;
> + }
> +
> + if (PciVidPid[0] != ASMEDIA_VID) {
> + continue;
> + }
> +
> + switch (PciVidPid[1]) {
> + case ASM1061_PID:
> + //
> + // The ASM1061 SATA controller as integrated into the DeveloperBox design
> + // emits too much electromagnetic radiation. So enable spread spectrum
> + // mode.
> + //
> + EnableAsm1061SpreadSpectrum (PciIo);
> + break;
> + case ASM1182E_PID:
> + case ASM1184E_PID:
> + //
> + // The ASM1184E 4-port PCIe switch on the DeveloperBox board (and its
> + // 2-port sibling of which samples were used in development) needs a
> + // little nudge to get it to train the downstream links at Gen2 speed.
> + //
> + if (mHiiSettings->Pcie0MaxSpeed != PCIE_MAX_SPEED_GEN1) {
> + RetrainAsm1184eDownstreamPort (PciIo);
> + }
> + break;
> + }
> }
> }
>
> EFI_STATUS
> EFIAPI
> -RegisterAsm1184Notifier (
> +RegisterPciIoNotifier (
> VOID
> )
> {
> diff --git a/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.c b/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.c
> index 11b31e77bd3f..f3b05fc973ed 100644
> --- a/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.c
> +++ b/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.c
> @@ -14,6 +14,9 @@
>
> #include "PlatformDxe.h"
>
> +UINT64 mHiiSettingsVal;
> +SYNQUACER_PLATFORM_VARSTORE_DATA *mHiiSettings;
> +
> typedef struct {
> VENDOR_DEVICE_PATH VendorDevicePath;
> EFI_DEVICE_PATH_PROTOCOL End;
> @@ -253,8 +256,9 @@ PlatformDxeEntryPoint (
> VOID *Dtb;
> UINTN DtbSize;
> EFI_HANDLE Handle;
> - UINT64 SettingsVal;
> - SYNQUACER_PLATFORM_VARSTORE_DATA *Settings;
> +
> + mHiiSettingsVal = PcdGet64 (PcdPlatformSettings);
> + mHiiSettings = (SYNQUACER_PLATFORM_VARSTORE_DATA *)&mHiiSettingsVal;
>
> Dtb = NULL;
> Status = DtPlatformLoadDtb (&Dtb, &DtbSize);
> @@ -294,17 +298,13 @@ PlatformDxeEntryPoint (
>
> SmmuEnableCoherentDma ();
>
> - SettingsVal = PcdGet64 (PcdPlatformSettings);
> - Settings = (SYNQUACER_PLATFORM_VARSTORE_DATA *)&SettingsVal;
> - if (Settings->Pcie0MaxSpeed != PCIE_MAX_SPEED_GEN1) {
> - Status = RegisterAsm1184Notifier ();
> - ASSERT_EFI_ERROR (Status);
> - }
> + Status = RegisterPciIoNotifier ();
> + ASSERT_EFI_ERROR (Status);
>
> Status = EnableSettingsForm ();
> ASSERT_EFI_ERROR (Status);
>
> - if (Settings->EnableEmmc == EMMC_ENABLED) {
> + if (mHiiSettings->EnableEmmc == EMMC_ENABLED) {
> Status = RegisterEmmc ();
> ASSERT_EFI_ERROR (Status);
> }
> diff --git a/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.h b/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.h
> index de7de12cec97..b634e8be99ad 100644
> --- a/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.h
> +++ b/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.h
> @@ -40,9 +40,12 @@
> extern UINT8 PlatformDxeHiiBin[];
> extern UINT8 PlatformDxeStrings[];
>
> +extern UINT64 mHiiSettingsVal;
> +extern SYNQUACER_PLATFORM_VARSTORE_DATA *mHiiSettings;
> +
> EFI_STATUS
> EFIAPI
> -RegisterAsm1184Notifier (
> +RegisterPciIoNotifier (
> VOID
> );
>
> diff --git a/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.inf b/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.inf
> index 16412b999a40..e13e16f3da6b 100644
> --- a/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.inf
> +++ b/Silicon/Socionext/SynQuacer/Drivers/PlatformDxe/PlatformDxe.inf
> @@ -23,8 +23,8 @@ [Defines]
> ENTRY_POINT = PlatformDxeEntryPoint
>
> [Sources]
> - Asmedia118x.c
> Emmc.c
> + Pci.c
> PlatformDxe.c
> PlatformDxeHii.uni
> PlatformDxeHii.vfr
> --
> 2.11.0
>
prev parent reply other threads:[~2018-01-24 11:56 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-24 11:57 [PATCH v2] Silicon/SynQuacer/PlatformDxe: enable spread spectrum mode for ASM1061 SATA Ard Biesheuvel
2018-01-24 12:02 ` Leif Lindholm [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-list from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180124120222.yyaih5vnylacreg6@bivouac.eciton.net \
--to=devel@edk2.groups.io \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox