Re: [PATCH v2] SD/eMMC : Fix Command Argument for SD/eMMC R/W operation.

[Leif Lindholm <leif.lindholm@linaro.org>]

I updated the subject line to start with EmbeddedPkg: instead.

On Thu, Jan 24, 2019 at 07:35:18PM +0530, Meenakshi Aggarwal wrote:
> Issue : SD read failure for high capacity cards e.g. 64 GB
> i

And I dropped the above stray i.
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>

Pushed as b566259c8a.

Thanks!

> Reason : Command argument value exceeds 32 bit for block number 0x3787FFF
> and cant be fit into 32 bit wide SD host controller register.
> 
> Fix :
> AccessMode bits [29:30] of OCR is a valid definition to calculate
> data address for eMMC cards.
> 
> For SD cards, data address is calculated on the basis of
> card capacity status bit[30] of OCR.
> 
> Contributed-under: TianoCore Contribution Agreement 1.1
> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
> ---
>  EmbeddedPkg/Universal/MmcDxe/Mmc.h        |  2 ++
>  EmbeddedPkg/Universal/MmcDxe/MmcBlockIo.c | 21 ++++++++++++++++-----
>  2 files changed, 18 insertions(+), 5 deletions(-)
> 
> diff --git a/EmbeddedPkg/Universal/MmcDxe/Mmc.h b/EmbeddedPkg/Universal/MmcDxe/Mmc.h
> index a77ba41..62de2c8 100644
> --- a/EmbeddedPkg/Universal/MmcDxe/Mmc.h
> +++ b/EmbeddedPkg/Universal/MmcDxe/Mmc.h
> @@ -70,6 +70,8 @@
>  #define SD_HIGH_SPEED                       50000000
>  #define SWITCH_CMD_SUCCESS_MASK             0x0f000000
>  
> +#define SD_CARD_CAPACITY                    0x00000002
> +
>  #define BUSWIDTH_4                          4
>  
>  typedef enum {
> diff --git a/EmbeddedPkg/Universal/MmcDxe/MmcBlockIo.c b/EmbeddedPkg/Universal/MmcDxe/MmcBlockIo.c
> index a2b9232..1dea7d3 100644
> --- a/EmbeddedPkg/Universal/MmcDxe/MmcBlockIo.c
> +++ b/EmbeddedPkg/Universal/MmcDxe/MmcBlockIo.c
> @@ -148,12 +148,23 @@ MmcTransferBlock (
>    MmcHostInstance = MMC_HOST_INSTANCE_FROM_BLOCK_IO_THIS (This);
>    MmcHost = MmcHostInstance->MmcHost;
>  
> -  //Set command argument based on the card access mode (Byte mode or Block mode)
> -  if ((MmcHostInstance->CardInfo.OCRData.AccessMode & MMC_OCR_ACCESS_MASK) ==
> -      MMC_OCR_ACCESS_SECTOR) {
> -    CmdArg = Lba;
> +  if (MmcHostInstance->CardInfo.CardType != EMMC_CARD) {
> +    //Set command argument based on the card capacity
> +    //if 0 : SDSC card
> +    //if 1 : SDXC/SDHC
> +    if (MmcHostInstance->CardInfo.OCRData.AccessMode & SD_CARD_CAPACITY) {
> +      CmdArg = Lba;
> +    } else {
> +      CmdArg = Lba * This->Media->BlockSize;
> +    }
>    } else {
> -    CmdArg = Lba * This->Media->BlockSize;
> +    //Set command argument based on the card access mode (Byte mode or Block mode)
> +    if ((MmcHostInstance->CardInfo.OCRData.AccessMode & MMC_OCR_ACCESS_MASK) ==
> +        MMC_OCR_ACCESS_SECTOR) {
> +      CmdArg = Lba;
> +    } else {
> +      CmdArg = Lba * This->Media->BlockSize;
> +    }
>    }
>  
>    Status = MmcHost->SendCommand (MmcHost, Cmd, CmdArg);
> -- 
> 1.9.1
>