[PATCH v3 4/7] Platform/RaspberryPi/Arasan: Add write delay and voltage/clock config

["Jeremy Linton" <jeremy.linton@arm.com>]

The uboot and linux drivers have notes that there is a clock domain crossing
problem that happens with back to back writes to the sd controllers on the
rpi. Its not clear if this is still applicable to the rpi4/emmc2 but
it seems wise to add it.

Futher, we need to assure that the card voltage is set to 3.3V, and
we should try and follow some of the SDHCI docs when it comes to
changing the clock.

Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrei Warkentin <awarkentin@vmware.com>
---
 .../Drivers/ArasanMmcHostDxe/ArasanMmcHostDxe.c    | 112 +++++++++++++++++----
 .../Drivers/ArasanMmcHostDxe/ArasanMmcHostDxe.h    |   1 +
 2 files changed, 93 insertions(+), 20 deletions(-)

diff --git a/Platform/RaspberryPi/Drivers/ArasanMmcHostDxe/ArasanMmcHostDxe.c b/Platform/RaspberryPi/Drivers/ArasanMmcHostDxe/ArasanMmcHostDxe.c
index 0cb7e85b38..a7b538a91a 100644
--- a/Platform/RaspberryPi/Drivers/ArasanMmcHostDxe/ArasanMmcHostDxe.c
+++ b/Platform/RaspberryPi/Drivers/ArasanMmcHostDxe/ArasanMmcHostDxe.c
@@ -18,6 +18,56 @@ UINT32 LastExecutedCommand = (UINT32) -1;
 STATIC RASPBERRY_PI_FIRMWARE_PROTOCOL *mFwProtocol;
 STATIC UINTN MMCHS_BASE;
 
+STATIC
+UINT32
+EFIAPI
+SdMmioWrite32 (
+  IN      UINTN                     Address,
+  IN      UINT32                    Value
+  )
+{
+  UINT32 ret;
+  ret = (UINT32)MmioWrite32 (Address, Value);
+  // There is a bug about clock domain crossing on writes, delay to avoid it
+  gBS->Stall (STALL_AFTER_REG_WRITE_US);
+  return ret;
+}
+
+STATIC
+UINT32
+EFIAPI
+SdMmioOr32 (
+  IN      UINTN                     Address,
+  IN      UINT32                    OrData
+  )
+{
+  return SdMmioWrite32 (Address, MmioRead32 (Address) | OrData);
+}
+
+STATIC
+UINT32
+EFIAPI
+SdMmioAnd32 (
+  IN      UINTN                     Address,
+  IN      UINT32                    AndData
+  )
+{
+  return SdMmioWrite32 (Address, MmioRead32 (Address) & AndData);
+}
+
+STATIC
+UINT32
+EFIAPI
+SdMmioAndThenOr32 (
+  IN      UINTN                     Address,
+  IN      UINT32                    AndData,
+  IN      UINT32                    OrData
+  )
+{
+  return SdMmioWrite32 (Address, (MmioRead32 (Address) & AndData) | OrData);
+}
+
+
 /**
    These SD commands are optional, according to the SD Spec
 **/
@@ -175,7 +225,9 @@ SoftReset (
   IN UINT32 Mask
   )
 {
-  MmioOr32 (MMCHS_SYSCTL, Mask);
+  DEBUG ((DEBUG_MMCHOST_SD, "SoftReset with mask 0x%x\n", Mask));
+
+  SdMmioOr32 (MMCHS_SYSCTL, Mask);
   if (PollRegisterWithMask (MMCHS_SYSCTL, Mask, 0) == EFI_TIMEOUT) {
     DEBUG ((DEBUG_ERROR, "Failed to SoftReset with mask 0x%x\n", Mask));
     return EFI_TIMEOUT;
@@ -326,29 +378,29 @@ MMCSendCommand (
   }
 
   if (IsAppCmd && MmcCmd == ACMD22) {
-    MmioWrite32 (MMCHS_BLK, 4);
+    SdMmioWrite32 (MMCHS_BLK, 4);
   } else if (IsAppCmd && MmcCmd == ACMD51) {
-    MmioWrite32 (MMCHS_BLK, 8);
+    SdMmioWrite32 (MMCHS_BLK, 8);
   } else if (!IsAppCmd && MmcCmd == CMD6) {
-    MmioWrite32 (MMCHS_BLK, 64);
+    SdMmioWrite32 (MMCHS_BLK, 64);
   } else if (IsADTCCmd) {
-    MmioWrite32 (MMCHS_BLK, BLEN_512BYTES);
+    SdMmioWrite32 (MMCHS_BLK, BLEN_512BYTES);
   }
 
   // Set Data timeout counter value to max value.
-  MmioAndThenOr32 (MMCHS_SYSCTL, (UINT32) ~DTO_MASK, DTO_VAL);
+  SdMmioAndThenOr32 (MMCHS_SYSCTL, (UINT32) ~DTO_MASK, DTO_VAL);
 
   //
   // Clear Interrupt Status Register, but not the Card Inserted bit
   // to avoid messing with card detection logic.
   //
-  MmioWrite32 (MMCHS_INT_STAT, ALL_EN & ~(CARD_INS));
+  SdMmioWrite32 (MMCHS_INT_STAT, ALL_EN & ~(CARD_INS));
 
   // Set command argument register
-  MmioWrite32 (MMCHS_ARG, Argument);
+  SdMmioWrite32 (MMCHS_ARG, Argument);
 
   // Send the command
-  MmioWrite32 (MMCHS_CMD, MmcCmd);
+  SdMmioWrite32 (MMCHS_CMD, MmcCmd);
 
   // Check for the command status.
   while (RetryCount < MAX_RETRY_COUNT) {
@@ -373,7 +425,7 @@ MMCSendCommand (
 
     // Check if command is completed.
     if ((MmcStatus & CC) == CC) {
-      MmioWrite32 (MMCHS_INT_STAT, CC);
+      SdMmioWrite32 (MMCHS_INT_STAT, CC);
       break;
     }
 
@@ -428,6 +480,21 @@ MMCNotifyState (
         return Status;
       }
 
+      DEBUG ((DEBUG_MMCHOST_SD, "ArasanMMCHost: CAP %X CAPH %X\n", MmioRead32(MMCHS_CAPA),MmioRead32(MMCHS_CUR_CAPA)));
+
+      // Lets switch to card detect test mode.
+      SdMmioOr32 (MMCHS_HCTL, BIT7|BIT6);
+
+      // set card voltage
+      SdMmioAnd32 (MMCHS_HCTL, ~SDBP_ON);
+      SdMmioAndThenOr32 (MMCHS_HCTL, (UINT32) ~SDBP_MASK, SDVS_3_3_V);
+      SdMmioOr32 (MMCHS_HCTL, SDBP_ON);
+
+      DEBUG ((DEBUG_MMCHOST_SD, "ArasanMMCHost: AC12 %X HCTL %X\n", MmioRead32(MMCHS_AC12),MmioRead32(MMCHS_HCTL)));
+
+      // First turn off the clock
+      SdMmioAnd32 (MMCHS_SYSCTL, ~CEN);
+
       // Attempt to set the clock to 400Khz which is the expected initialization speed
       Status = CalculateClockFrequencyDivisor (400000, &Divisor, NULL);
       if (EFI_ERROR (Status)) {
@@ -436,10 +503,15 @@ MMCNotifyState (
       }
 
       // Set Data Timeout Counter value, set clock frequency, enable internal clock
-      MmioOr32 (MMCHS_SYSCTL, DTO_VAL | Divisor | CEN | ICS | ICE);
+      SdMmioOr32 (MMCHS_SYSCTL, DTO_VAL | Divisor | CEN | ICS | ICE);
+      SdMmioOr32 (MMCHS_HCTL, SDBP_ON);
+      // wait for ICS
+      while ((MmioRead32 (MMCHS_SYSCTL) & ICS_MASK) != ICS);
+
+      DEBUG ((DEBUG_MMCHOST_SD, "ArasanMMCHost: AC12 %X HCTL %X\n", MmioRead32(MMCHS_AC12),MmioRead32(MMCHS_HCTL)));
 
       // Enable interrupts
-      MmioWrite32 (MMCHS_IE, ALL_EN);
+      SdMmioWrite32 (MMCHS_IE, ALL_EN);
     }
     break;
   case MmcIdleState:
@@ -452,7 +524,7 @@ MMCNotifyState (
     ClockFrequency = 25000000;
 
     // First turn off the clock
-    MmioAnd32 (MMCHS_SYSCTL, ~CEN);
+    SdMmioAnd32 (MMCHS_SYSCTL, ~CEN);
 
     Status = CalculateClockFrequencyDivisor (ClockFrequency, &Divisor, NULL);
     if (EFI_ERROR (Status)) {
@@ -462,13 +534,13 @@ MMCNotifyState (
     }
 
     // Setup new divisor
-    MmioAndThenOr32 (MMCHS_SYSCTL, (UINT32) ~CLKD_MASK, Divisor);
+    SdMmioAndThenOr32 (MMCHS_SYSCTL, (UINT32) ~CLKD_MASK, Divisor);
 
     // Wait for the clock to stabilise
     while ((MmioRead32 (MMCHS_SYSCTL) & ICS_MASK) != ICS);
 
     // Set Data Timeout Counter value, set clock frequency, enable internal clock
-    MmioOr32 (MMCHS_SYSCTL, CEN);
+    SdMmioOr32 (MMCHS_SYSCTL, CEN);
     break;
   case MmcTransferState:
     break;
@@ -635,7 +707,7 @@ MMCReadBlockData (
     while (RetryCount < MAX_RETRY_COUNT) {
       MmcStatus = MmioRead32 (MMCHS_INT_STAT);
       if ((MmcStatus & BRR) != 0) {
-        MmioWrite32 (MMCHS_INT_STAT, BRR);
+        SdMmioWrite32 (MMCHS_INT_STAT, BRR);
         /*
          * Data is ready.
          */
@@ -662,7 +734,7 @@ MMCReadBlockData (
     gBS->Stall (STALL_AFTER_READ_US);
   }
 
-  MmioWrite32 (MMCHS_INT_STAT, BRR);
+  SdMmioWrite32 (MMCHS_INT_STAT, BRR);
   return EFI_SUCCESS;
 }
 
@@ -699,13 +771,13 @@ MMCWriteBlockData (
     while (RetryCount < MAX_RETRY_COUNT) {
       MmcStatus = MmioRead32 (MMCHS_INT_STAT);
       if ((MmcStatus & BWR) != 0) {
-        MmioWrite32 (MMCHS_INT_STAT, BWR);
+        SdMmioWrite32 (MMCHS_INT_STAT, BWR);
         /*
          * Can write data.
          */
         mFwProtocol->SetLed (TRUE);
         for (Count = 0; Count < BlockLen; Count += 4, Buffer++) {
-          MmioWrite32 (MMCHS_DATA, *Buffer);
+          SdMmioWrite32 (MMCHS_DATA, *Buffer);
         }
 
         mFwProtocol->SetLed (FALSE);
@@ -726,7 +798,7 @@ MMCWriteBlockData (
     gBS->Stall (STALL_AFTER_WRITE_US);
   }
 
-  MmioWrite32 (MMCHS_INT_STAT, BWR);
+  SdMmioWrite32 (MMCHS_INT_STAT, BWR);
   return EFI_SUCCESS;
 }
 
diff --git a/Platform/RaspberryPi/Drivers/ArasanMmcHostDxe/ArasanMmcHostDxe.h b/Platform/RaspberryPi/Drivers/ArasanMmcHostDxe/ArasanMmcHostDxe.h
index 6cd600f738..e94606cc5b 100644
--- a/Platform/RaspberryPi/Drivers/ArasanMmcHostDxe/ArasanMmcHostDxe.h
+++ b/Platform/RaspberryPi/Drivers/ArasanMmcHostDxe/ArasanMmcHostDxe.h
@@ -37,6 +37,7 @@
 #define STALL_AFTER_REC_RESP_US (50)
 #define STALL_AFTER_WRITE_US (200)
 #define STALL_AFTER_READ_US (20)
+#define STALL_AFTER_REG_WRITE_US (10)
 #define STALL_AFTER_RETRY_US (20)
 
 #define MAX_DIVISOR_VALUE 1023
-- 
2.13.7