[Patch V2 15/40] TigerlakeSiliconPkg/IpBlock: Add Espi component

["Heng Luo" <heng.luo@intel.com>]

REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3171

Adds the following files:
  * IpBlock/Espi/Library

Cc: Sai Chaganty <rangasai.v.chaganty@intel.com>
Cc: Nate DeSimone <nathaniel.l.desimone@intel.com>
Signed-off-by: Heng Luo <heng.luo@intel.com>
---
 Silicon/Intel/TigerlakeSiliconPkg/IpBlock/Espi/Library/PeiDxeSmmEspiLib/EspiLib.c            | 469 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 Silicon/Intel/TigerlakeSiliconPkg/IpBlock/Espi/Library/PeiDxeSmmEspiLib/PeiDxeSmmEspiLib.inf |  38 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 507 insertions(+)

diff --git a/Silicon/Intel/TigerlakeSiliconPkg/IpBlock/Espi/Library/PeiDxeSmmEspiLib/EspiLib.c b/Silicon/Intel/TigerlakeSiliconPkg/IpBlock/Espi/Library/PeiDxeSmmEspiLib/EspiLib.c
new file mode 100644
index 0000000000..2d1928ce18
--- /dev/null
+++ b/Silicon/Intel/TigerlakeSiliconPkg/IpBlock/Espi/Library/PeiDxeSmmEspiLib/EspiLib.c
@@ -0,0 +1,469 @@
+/** @file
+  This file contains routines for eSPI
+
+  Copyright (c) 2021, Intel Corporation. All rights reserved.<BR>
+  SPDX-License-Identifier: BSD-2-Clause-Patent
+**/
+#include <Base.h>
+#include <Uefi/UefiBaseType.h>
+#include <Library/IoLib.h>
+#include <Library/DebugLib.h>
+#include <Library/BaseMemoryLib.h>
+#include <Library/EspiLib.h>
+#include <Library/PchPcrLib.h>
+#include <Library/PchInfoLib.h>
+#include <Library/TimerLib.h>
+#include <PchLimits.h>
+#include <Register/PchPcrRegs.h>
+#include <Register/PchRegsLpc.h>
+
+#define CHANNEL_RESET_TIMEOUT     100   ///< Channel reset timeout in us after which to report error
+#define SLAVE_CHANNELS_MAX        7     ///< Max number of channels
+
+//
+// eSPI Slave registers
+//
+#define R_ESPI_SLAVE_GENCAP               0x08      ///< General Capabilities and Configurations
+#define B_ESPI_SLAVE_GENCAP_SUPPCHAN      0xFF      ///< Channels supported bit mask
+#define R_ESPI_SLAVE_CHACAP_BASE          0x10      ///< Base address from which channel Cap and Conf registers start on slave
+#define S_ESPI_SLAVE_CHACAP_OFFSET        0x10      ///< Offset for each channel from base
+#define B_ESPI_SLAVE_CHACAP_CHEN          BIT0      ///< Slave Channel enable bit
+#define B_ESPI_SLAVE_CHACAP_CHRDY         BIT1      ///< Slave Channel ready bit
+
+/**
+  Checks if second slave capability is enabled
+
+  @retval TRUE      There's second slave
+  @retval FALSE     There's no second slave
+**/
+BOOLEAN
+IsEspiSecondSlaveSupported (
+  VOID
+  )
+{
+  return FALSE;
+}
+
+/**
+  Checks in slave General Capabilities register if it supports channel with requested number
+
+  @param[in]  SlaveId         Id of slave to check
+  @param[in]  ChannelNumber   Number of channel of which to check
+
+  @retval TRUE      Channel with requested number is supported by slave device
+  @retval FALSE     Channel with requested number is not supported by slave device
+**/
+BOOLEAN
+IsEspiSlaveChannelSupported (
+  UINT8   SlaveId,
+  UINT8   ChannelNumber
+  )
+{
+  UINT32  Data32;
+  UINT8   SupportedChannels;
+
+  PchEspiSlaveGetConfig (SlaveId, R_ESPI_SLAVE_GENCAP, &Data32);
+  SupportedChannels = (UINT8) (Data32 & B_ESPI_SLAVE_GENCAP_SUPPCHAN);
+
+  DEBUG ((DEBUG_INFO, "Slave %d supported channels 0x%4X\n", SlaveId, SupportedChannels));
+
+  if (ChannelNumber > SLAVE_CHANNELS_MAX || !(SupportedChannels & (BIT0 << ChannelNumber))) {
+    // Incorrect channel number was specified. Either exceeded max or Slave doesn't support that channel.
+    return FALSE;
+  }
+
+  return TRUE;
+}
+
+/**
+  Is eSPI enabled in strap.
+
+  @retval TRUE          Espi is enabled in strap
+  @retval FALSE         Espi is disabled in strap
+**/
+BOOLEAN
+IsEspiEnabled (
+  VOID
+  )
+{
+  return (PchPcrRead32 (PID_ESPISPI, R_ESPI_PCR_CFG_VAL) & B_ESPI_PCR_CFG_VAL_ESPI_EN) != 0;
+}
+
+/**
+  eSPI helper function to clear slave configuration register status
+
+  @retval EFI_SUCCESS Write to private config space succeed
+  @retval others      Read / Write failed
+**/
+STATIC
+VOID
+EspiClearScrs (
+  VOID
+  )
+{
+  PchPcrAndThenOr32 (
+    PID_ESPISPI,
+    R_ESPI_PCR_SLV_CFG_REG_CTL,
+    (UINT32) ~0,
+     B_ESPI_PCR_SLV_CFG_REG_CTL_SCRS
+     );
+}
+
+/**
+  eSPI helper function to poll slave configuration register enable for 0
+  and to check for slave configuration register status
+
+  @retval EFI_SUCCESS       Enable bit is zero and no error in status bits
+  @retval EFI_DEVICE_ERROR  Error in SCRS
+  @retval others            Read / Write to private config space failed
+**/
+STATIC
+EFI_STATUS
+EspiPollScreAndCheckScrs (
+  VOID
+  )
+{
+  UINT32     ScrStat;
+
+  do {
+    ScrStat = PchPcrRead32 (PID_ESPISPI, R_ESPI_PCR_SLV_CFG_REG_CTL);
+  } while ((ScrStat & B_ESPI_PCR_SLV_CFG_REG_CTL_SCRE) != 0);
+
+  ScrStat = (ScrStat & B_ESPI_PCR_SLV_CFG_REG_CTL_SCRS) >> N_ESPI_PCR_SLV_CFG_REG_CTL_SCRS;
+  if (ScrStat != V_ESPI_PCR_SLV_CFG_REG_CTL_SCRS_NOERR) {
+    DEBUG ((DEBUG_ERROR, "eSPI slave config register status (error) is %x \n", ScrStat));
+    return EFI_DEVICE_ERROR;
+  }
+  return EFI_SUCCESS;
+}
+
+typedef enum {
+  EspiSlaveOperationConfigRead,
+  EspiSlaveOperationConfigWrite,
+  EspiSlaveOperationStatusRead,
+  EspiSlaveOperationInBandReset
+} ESPI_SLAVE_OPERATION;
+
+/**
+  Helper library to do all the operations regards to eSPI slave
+
+  @param[in]      SlaveId         eSPI Slave ID
+  @param[in]      SlaveAddress    Slave address to be put in R_ESPI_PCR_SLV_CFG_REG_CTL[11:0]
+  @param[in]      SlaveOperation  Based on ESPI_SLAVE_OPERATION
+  @param[in,out]  Data
+
+  @retval EFI_SUCCESS           Operation succeed
+  @retval EFI_INVALID_PARAMETER Slave ID is not supported or SlaveId 1 is used in PCH_LP
+  @retval EFI_INVALID_PARAMETER Slave configuration register address exceed maximum allowed
+  @retval EFI_INVALID_PARAMETER Slave configuration register address is not DWord aligned
+  @retval EFI_ACCESS_DENIED     eSPI Slave write to address range 0 to 0x7FF has been locked
+  @retval EFI_DEVICE_ERROR      Error in SCRS during polling stage of operation
+**/
+STATIC
+EFI_STATUS
+EspiSlaveOperationHelper (
+  IN     UINT32               SlaveId,
+  IN     UINT32               SlaveAddress,
+  IN     ESPI_SLAVE_OPERATION SlaveOperation,
+  IN OUT UINT32               *Data
+  )
+{
+  EFI_STATUS  Status;
+  UINT32      Data32;
+
+  //
+  // Check the SlaveId is 0 or 1
+  //
+  if (SlaveId >= PCH_MAX_ESPI_SLAVES) {
+    DEBUG ((DEBUG_ERROR, "eSPI Slave ID of %d or more is not accepted \n", PCH_MAX_ESPI_SLAVES));
+    return EFI_INVALID_PARAMETER;
+  }
+  //
+  // Check if SlaveId 1 is used, it is not a PCH_LP
+  //
+  if (SlaveId == 1) {
+    return EFI_INVALID_PARAMETER;
+  }
+  //
+  // Check the address is not more then 0xFFF
+  //
+  if (SlaveAddress > B_ESPI_PCR_SLV_CFG_REG_CTL_SCRA) {
+    DEBUG ((DEBUG_ERROR, "eSPI Slave address must be less than 0x%x \n", (B_ESPI_PCR_SLV_CFG_REG_CTL_SCRA + 1)));
+    return EFI_INVALID_PARAMETER;
+  }
+  //
+  // Check the address is DWord aligned
+  //
+  if ((SlaveAddress & 0x3) != 0) {
+    DEBUG ((DEBUG_ERROR, "eSPI Slave address must be DWord aligned \n"));
+    return EFI_INVALID_PARAMETER;
+  }
+
+  //
+  // Check if write is allowed
+  //
+  if ((SlaveOperation == EspiSlaveOperationConfigWrite) &&
+      (SlaveAddress <= 0x7FF)) {
+
+    //
+    // If the SLCRR is not set in corresponding slave, we will check the lock bit
+    //
+    Data32 = PchPcrRead32 (PID_ESPISPI, (UINT16) (R_ESPI_PCR_LNKERR_SLV0 + (SlaveId * S_ESPI_PCR_LNKERR_SLV0)));
+    if ((Data32 & B_ESPI_PCR_LNKERR_SLV0_SLCRR) == 0) {
+
+      Data32 = PchPcrRead32 (PID_ESPISPI, (UINT16) R_ESPI_PCR_SLV_CFG_REG_CTL);
+      if ((Data32 & B_ESPI_PCR_SLV_CFG_REG_CTL_SBLCL) != 0) {
+        DEBUG ((DEBUG_ERROR, "eSPI Slave write to address range 0 to 0x7FF has been locked \n"));
+        return EFI_ACCESS_DENIED;
+      }
+    }
+  }
+
+  //
+  // Input check done, now go through all the processes
+  //
+   EspiClearScrs ();
+
+  if (SlaveOperation == EspiSlaveOperationConfigWrite) {
+    PchPcrWrite32 (
+      PID_ESPISPI,
+      (UINT16) R_ESPI_PCR_SLV_CFG_REG_DATA,
+      *Data
+      );
+  }
+
+  PchPcrAndThenOr32 (
+    PID_ESPISPI,
+    (UINT16) R_ESPI_PCR_SLV_CFG_REG_CTL,
+    (UINT32) ~(B_ESPI_PCR_SLV_CFG_REG_CTL_SID | B_ESPI_PCR_SLV_CFG_REG_CTL_SCRT | B_ESPI_PCR_SLV_CFG_REG_CTL_SCRA),
+    (B_ESPI_PCR_SLV_CFG_REG_CTL_SCRE |
+     (SlaveId << N_ESPI_PCR_SLV_CFG_REG_CTL_SID) |
+     (((UINT32) SlaveOperation) << N_ESPI_PCR_SLV_CFG_REG_CTL_SCRT) |
+     SlaveAddress
+     )
+    );
+
+  Status = EspiPollScreAndCheckScrs ();
+  if (EFI_ERROR (Status)) {
+    return Status;
+  }
+
+  if ((SlaveOperation == EspiSlaveOperationConfigRead) || (SlaveOperation == EspiSlaveOperationStatusRead)) {
+    Data32 = PchPcrRead32 (
+               PID_ESPISPI,
+               (UINT16) R_ESPI_PCR_SLV_CFG_REG_DATA
+               );
+    if (SlaveOperation == EspiSlaveOperationStatusRead) {
+      *Data = Data32 & 0xFFFF;
+    } else {
+      *Data = Data32;
+    }
+  }
+
+  return EFI_SUCCESS;
+}
+
+/**
+  Get configuration from eSPI slave
+
+  @param[in]  SlaveId       eSPI slave ID
+  @param[in]  SlaveAddress  Slave Configuration Register Address
+  @param[out] OutData       Configuration data read
+
+  @retval EFI_SUCCESS           Operation succeed
+  @retval EFI_INVALID_PARAMETER Slave ID is not supported
+  @retval EFI_INVALID_PARAMETER Slave ID is not supported or SlaveId 1 is used in PCH_LP
+  @retval EFI_INVALID_PARAMETER Slave configuration register address exceed maximum allowed
+  @retval EFI_INVALID_PARAMETER Slave configuration register address is not DWord aligned
+  @retval EFI_DEVICE_ERROR      Error in SCRS during polling stage of operation
+**/
+EFI_STATUS
+PchEspiSlaveGetConfig (
+  IN  UINT32 SlaveId,
+  IN  UINT32 SlaveAddress,
+  OUT UINT32 *OutData
+  )
+{
+  //
+  // 1. Clear status from previous transaction by writing 111b to status in SCRS, PCR[eSPI] + 4000h [30:28]
+  // 2. Program SLV_CFG_REG_CTL with the right value (Bit[31]=01, Bit [20:19]=<SlvID>, Bit [17:16] = 00b, Bit[11:0] = <addr_xxx>.
+  // 3. Poll the SCRE (PCR[eSPI] +4000h [31]) to be set back to 0
+  // 4. Check the transaction status in SCRS (bits [30:28])
+  // 5. Read SLV_CFG_REG_DATA.
+  //
+  return EspiSlaveOperationHelper (SlaveId, SlaveAddress, EspiSlaveOperationConfigRead, OutData);
+}
+
+/**
+  Set eSPI slave configuration
+
+  Note: A Set_Configuration must always be followed by a Get_Configuration in order to ensure
+  that the internal state of the eSPI-MC is consistent with the Slave's register settings.
+
+  @param[in]  SlaveId       eSPI slave ID
+  @param[in]  SlaveAddress  Slave Configuration Register Address
+  @param[in]  InData        Configuration data to write
+
+  @retval EFI_SUCCESS           Operation succeed
+  @retval EFI_INVALID_PARAMETER Slave ID is not supported or SlaveId 1 is used in PCH_LP
+  @retval EFI_INVALID_PARAMETER Slave configuration register address exceed maximum allowed
+  @retval EFI_INVALID_PARAMETER Slave configuration register address is not DWord aligned
+  @retval EFI_ACCESS_DENIED     eSPI Slave write to address range 0 to 0x7FF has been locked
+  @retval EFI_DEVICE_ERROR      Error in SCRS during polling stage of operation
+**/
+EFI_STATUS
+PchEspiSlaveSetConfig (
+  IN  UINT32 SlaveId,
+  IN  UINT32 SlaveAddress,
+  IN  UINT32 InData
+  )
+{
+  EFI_STATUS  Status;
+  UINT32      Data32;
+
+  //
+  // 1. Clear status from previous transaction by writing 111b to status in SCRS, PCR[eSPI] + 4000h [30:28]
+  // 2. Program SLV_CFG_REG_DATA with the write value.
+  // 3. Program SLV_CFG_REG_CTL with the right value (Bit[31]=01, Bit [20:19]=<SlvID>, Bit [17:16] = 01b, Bit[11:0] = <addr_xxx>.
+  // 4. Poll the SCRE (PCR[eSPI] +4000h [31]) to be set back to 0
+  // 5. Check the transaction status in SCRS (bits [30:28])
+  //
+  Status = EspiSlaveOperationHelper (SlaveId, SlaveAddress, EspiSlaveOperationConfigWrite, &InData);
+  PchEspiSlaveGetConfig (SlaveId, SlaveAddress, &Data32);
+  return Status;
+}
+
+/**
+  Get status from eSPI slave
+
+  @param[in]  SlaveId       eSPI slave ID
+  @param[out] OutData       Configuration data read
+
+  @retval EFI_SUCCESS           Operation succeed
+  @retval EFI_INVALID_PARAMETER Slave ID is not supported or SlaveId 1 is used in PCH_LP
+  @retval EFI_DEVICE_ERROR      Error in SCRS during polling stage of operation
+**/
+EFI_STATUS
+PchEspiSlaveGetStatus (
+  IN  UINT32 SlaveId,
+  OUT UINT16 *OutData
+  )
+{
+  EFI_STATUS  Status;
+  UINT32      TempOutData;
+
+  TempOutData = 0;
+
+  //
+  // 1. Clear status from previous transaction by writing 111b to status in SCRS, PCR[eSPI] + 4000h [30:28]
+  // 2. Program SLV_CFG_REG_CTL with the right value (Bit[31]=01, Bit [20:19]=<SlvID>, Bit [17:16] = 10b, Bit[11:0] = <addr_xxx>.
+  // 3. Poll the SCRE (PCR[eSPI] +4000h [31]) to be set back to 0
+  // 4. Check the transaction status in SCRS (bits [30:28])
+  // 5. Read SLV_CFG_REG_DATA [15:0].
+  //
+  Status = EspiSlaveOperationHelper (SlaveId, 0, EspiSlaveOperationStatusRead, &TempOutData);
+  *OutData = (UINT16) TempOutData;
+
+  return Status;
+}
+
+/**
+  eSPI slave in-band reset
+
+  @param[in]  SlaveId           eSPI slave ID
+
+  @retval EFI_SUCCESS           Operation succeed
+  @retval EFI_INVALID_PARAMETER Slave ID is not supported or SlaveId 1 is used in PCH_LP
+  @retval EFI_DEVICE_ERROR      Error in SCRS during polling stage of operation
+**/
+EFI_STATUS
+PchEspiSlaveInBandReset (
+  IN  UINT32 SlaveId
+  )
+{
+  //
+  // 1. Clear status from previous transaction by writing 111b to status in SCRS, PCR[eSPI] + 4000h [30:28]
+  // 2. Program SLV_CFG_REG_CTL with the right value (Bit[31]=01, Bit [20:19]=<SlvID>, Bit [17:16] = 11b).
+  // 3. Poll the SCRE (PCR[eSPI] +4000h [31]) to be set back to 0
+  // 4. Check the transaction status in SCRS (bits [30:28])
+  //
+  return EspiSlaveOperationHelper (SlaveId, 0, EspiSlaveOperationInBandReset, NULL);
+}
+
+/**
+  eSPI Slave channel reset helper function
+
+  @param[in]  SlaveId           eSPI slave ID
+  @param[in]  ChannelNumber     Number of channel to reset
+
+  @retval     EFI_SUCCESS       Operation succeeded
+  @retval     EFI_UNSUPPORTED   Slave doesn't support that channel or invalid number specified
+  @retval     EFI_TIMEOUT       Operation has timeouted
+**/
+EFI_STATUS
+PchEspiSlaveChannelReset (
+  IN  UINT8   SlaveId,
+  IN  UINT8   ChannelNumber
+  )
+{
+  UINT8       Timeout;
+  UINT32      Data32;
+  UINT32      SlaveChannelAddress;
+  BOOLEAN     SlaveBmeSet;
+
+  DEBUG ((DEBUG_INFO, "eSPI slave %d channel %d reset\n", SlaveId, ChannelNumber));
+
+  Timeout = CHANNEL_RESET_TIMEOUT;
+  SlaveBmeSet = FALSE;
+
+  if (!IsEspiSlaveChannelSupported (SlaveId, ChannelNumber)) {
+    // Incorrect channel number was specified. Either exceeded max or Slave doesn't support that channel.
+    DEBUG ((DEBUG_ERROR, "Channel %d is not valid channel number for slave %d!\n", ChannelNumber, SlaveId));
+    return EFI_UNSUPPORTED;
+  }
+
+  // Calculating slave channel address
+  SlaveChannelAddress = R_ESPI_SLAVE_CHACAP_BASE + (S_ESPI_SLAVE_CHACAP_OFFSET * ChannelNumber);
+
+  // If we're resetting Peripheral Channel then we need to disable Bus Mastering first and reenable after reset
+  if (ChannelNumber == 0) {
+    PchEspiSlaveGetConfig (SlaveId, SlaveChannelAddress, &Data32);
+    if ((Data32 & B_ESPI_SLAVE_BME) != 0) {
+      Data32 &= ~(B_ESPI_SLAVE_BME);
+      PchEspiSlaveSetConfig (SlaveId, SlaveChannelAddress, Data32);
+      SlaveBmeSet = TRUE;
+    }
+  }
+
+  // Disable channel
+  PchEspiSlaveGetConfig (SlaveId, SlaveChannelAddress, &Data32);
+  Data32 &= ~(B_ESPI_SLAVE_CHACAP_CHEN);
+  PchEspiSlaveSetConfig (SlaveId, SlaveChannelAddress, Data32);
+
+  // Enable channel
+  PchEspiSlaveGetConfig (SlaveId, SlaveChannelAddress, &Data32);
+  Data32 |= B_ESPI_SLAVE_CHACAP_CHEN;
+  PchEspiSlaveSetConfig (SlaveId, SlaveChannelAddress, Data32);
+
+  DEBUG ((DEBUG_INFO, "Waiting for Channel Ready bit\n"));
+  // Wait until channel is ready by polling Channel Ready bit
+  while (((Data32 & B_ESPI_SLAVE_CHACAP_CHRDY) == 0) && (Timeout > 0)) {
+    PchEspiSlaveGetConfig (SlaveId, SlaveChannelAddress, &Data32);
+    MicroSecondDelay (1);
+    --Timeout;
+  }
+
+  if (Timeout == 0) {
+    // The waiting for channel to be ready has timed out
+    DEBUG ((DEBUG_ERROR, "The operation of channel %d reset for slave %d has timed out!\n", ChannelNumber, SlaveId));
+    return EFI_TIMEOUT;
+  }
+
+  if (ChannelNumber == 0 && SlaveBmeSet) {
+    PchEspiSlaveGetConfig (SlaveId, SlaveChannelAddress, &Data32);
+    Data32 |= B_ESPI_SLAVE_BME;
+    PchEspiSlaveSetConfig (SlaveId, SlaveChannelAddress, Data32);
+  }
+
+  return EFI_SUCCESS;
+}
diff --git a/Silicon/Intel/TigerlakeSiliconPkg/IpBlock/Espi/Library/PeiDxeSmmEspiLib/PeiDxeSmmEspiLib.inf b/Silicon/Intel/TigerlakeSiliconPkg/IpBlock/Espi/Library/PeiDxeSmmEspiLib/PeiDxeSmmEspiLib.inf
new file mode 100644
index 0000000000..440051432f
--- /dev/null
+++ b/Silicon/Intel/TigerlakeSiliconPkg/IpBlock/Espi/Library/PeiDxeSmmEspiLib/PeiDxeSmmEspiLib.inf
@@ -0,0 +1,38 @@
+## @file
+# Component description file for the PeiDxeSmmPchEspiLib
+#
+#  Copyright (c) 2021, Intel Corporation. All rights reserved.<BR>
+#  SPDX-License-Identifier: BSD-2-Clause-Patent
+#
+##
+
+
+[Defines]
+INF_VERSION = 0x00010017
+BASE_NAME = PeiDxeSmmEspiLib
+FILE_GUID = 7F25F990-7989-4413-B414-1EDE557E9389
+VERSION_STRING = 1.0
+MODULE_TYPE = BASE
+LIBRARY_CLASS = EspiLib
+#
+# The following information is for reference only and not required by the build tools.
+#
+# VALID_ARCHITECTURES = IA32 X64 IPF EBC
+#
+
+
+
+[LibraryClasses]
+BaseLib
+IoLib
+DebugLib
+PchPcrLib
+TimerLib
+
+[Packages]
+MdePkg/MdePkg.dec
+TigerlakeSiliconPkg/SiPkg.dec
+
+
+[Sources]
+EspiLib.c
-- 
2.24.0.windows.2