[edk2-devel] [PATCH v2 1/5] Platform/RaspberryPi/DualSerialPortLib: Always configure the pl011

["Jeremy Linton" <jeremy.linton@arm.com>]

The rpi's config.txt controls which uart (pl011, or miniuart) is
selected as the console. TFA and edk2 follow its lead, but if the
miniuart is selected as the primary and the machine is booted in ACPI
mode the baud/etc is never configured for the pl011. The linux kernel
won't reconfigure it either as its listed as a "SBSA" uart, so it
simply won't work.

This re-enables BT on the pl011 in ACPI mode, and it somewhat starts
to work again.

Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
---
 .../DualSerialPortLib/DualSerialPortLib.c     | 44 ++++++++++++-------
 1 file changed, 29 insertions(+), 15 deletions(-)

diff --git a/Platform/RaspberryPi/Library/DualSerialPortLib/DualSerialPortLib.c b/Platform/RaspberryPi/Library/DualSerialPortLib/DualSerialPortLib.c
index d2f983bf0a..09d3e33c00 100644
--- a/Platform/RaspberryPi/Library/DualSerialPortLib/DualSerialPortLib.c
+++ b/Platform/RaspberryPi/Library/DualSerialPortLib/DualSerialPortLib.c
@@ -76,6 +76,8 @@ SerialPortInitialize (
   EFI_PARITY_TYPE     Parity;
   UINT8               DataBits;
   EFI_STOP_BITS_TYPE  StopBits;
+  RETURN_STATUS       Ret;
+  UINTN               Timeout;
 
   //
   // First thing we need to do is determine which of PL011 or miniUART is selected
@@ -85,23 +87,34 @@ SerialPortInitialize (
     UsePl011UartSet = TRUE;
   }
 
-  if (UsePl011Uart) {
-    BaudRate = FixedPcdGet64 (PcdUartDefaultBaudRate);
+  // always init the pl011 on the RPi4, linux expects a SBSA uart to be at 115200
+  // this means we need to set the baud/etc even if we aren't using it as a console
+  if ((UsePl011Uart) || (RPI_MODEL == 4)) {
     ReceiveFifoDepth = 0;         // Use default FIFO depth
+    if (!UsePl011Uart)
+    {
+      BaudRate = 115200;
+    }
+    else
+    {
+      BaudRate = FixedPcdGet64 (PcdUartDefaultBaudRate);
+    }
     Parity = (EFI_PARITY_TYPE)FixedPcdGet8 (PcdUartDefaultParity);
     DataBits = FixedPcdGet8 (PcdUartDefaultDataBits);
     StopBits = (EFI_STOP_BITS_TYPE) FixedPcdGet8 (PcdUartDefaultStopBits);
 
-    return PL011UartInitializePort (
-             PL011_UART_REGISTER_BASE,
-             PL011UartClockGetFreq(),
-             &BaudRate,
-             &ReceiveFifoDepth,
-             &Parity,
-             &DataBits,
-             &StopBits
-             );
-  } else {
+    Ret = PL011UartInitializePort (
+           PL011_UART_REGISTER_BASE,
+           PL011UartClockGetFreq(),
+           &BaudRate,
+           &ReceiveFifoDepth,
+           &Parity,
+           &DataBits,
+           &StopBits
+           );
+  }
+
+  if (!UsePl011Uart) {
     SerialRegisterBase = MINI_UART_REGISTER_BASE;
     Divisor = SerialPortGetDivisor (PcdGet32 (PcdSerialBaudRate));
 
@@ -127,7 +140,8 @@ SerialPortInitialize (
     // Wait for the serial port to be ready.
     // Verify that both the transmit FIFO and the shift register are empty.
     //
-    while ((SerialPortReadRegister (SerialRegisterBase, R_UART_LSR) & (B_UART_LSR_TEMT | B_UART_LSR_TXRDY)) != (B_UART_LSR_TEMT | B_UART_LSR_TXRDY));
+    Timeout = 1000;
+    while (((SerialPortReadRegister (SerialRegisterBase, R_UART_LSR) & (B_UART_LSR_TEMT | B_UART_LSR_TXRDY)) != (B_UART_LSR_TEMT | B_UART_LSR_TXRDY)) && (Timeout--));
 
     //
     // Configure baud rate
@@ -158,9 +172,9 @@ SerialPortInitialize (
     // Put Modem Control Register(MCR) into its reset state of 0x00.
     //
     SerialPortWriteRegister (SerialRegisterBase, R_UART_MCR, 0x00);
-
-    return RETURN_SUCCESS;
+    Ret = RETURN_SUCCESS;
   }
+  return Ret;
 }
 
 /**
-- 
2.43.0



-=-=-=-=-=-=-=-=-=-=-=-
Groups.io Links: You receive all messages sent to this group.
View/Reply Online (#113961): https://edk2.groups.io/g/devel/message/113961
Mute This Topic: https://groups.io/mt/103796307/7686176
Group Owner: devel+owner@edk2.groups.io
Unsubscribe: https://edk2.groups.io/g/devel/unsub [rebecca@openfw.io]
-=-=-=-=-=-=-=-=-=-=-=-