From: "Tian, Feng" <feng.tian@intel.com>
To: Haojian Zhuang <haojian.zhuang@linaro.org>,
"leif.lindholm@linaro.org" <leif.lindholm@linaro.org>,
"ard.biesheuvel@linaro.org" <ard.biesheuvel@linaro.org>,
"edk2-devel@lists.01.org" <edk2-devel@lists.01.org>
Cc: "Tian, Feng" <feng.tian@intel.com>
Subject: Re: [PATCH 7/9] Ufs: fix initialize OCS value to 0x0F
Date: Fri, 6 Jan 2017 07:26:06 +0000 [thread overview]
Message-ID: <7F1BAD85ADEA444D97065A60D2E97EE5699A5FFA@SHSMSX101.ccr.corp.intel.com> (raw)
In-Reply-To: <1483685538-11058-8-git-send-email-haojian.zhuang@linaro.org>
Same with previous patches, could you please fix Ufs PEI driver as well?
Reviewed-by: Feng Tian <feng.tian@intel.com>
Thanks
Feng
-----Original Message-----
From: edk2-devel [mailto:edk2-devel-bounces@lists.01.org] On Behalf Of Haojian Zhuang
Sent: Friday, January 6, 2017 2:52 PM
To: Tian, Feng <feng.tian@intel.com>; leif.lindholm@linaro.org; ard.biesheuvel@linaro.org; edk2-devel@lists.01.org
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Subject: [edk2] [PATCH 7/9] Ufs: fix initialize OCS value to 0x0F
The OCS value should be initiliazed as 0x0F according to UFS spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
MdeModulePkg/Bus/Ufs/UfsPassThruDxe/UfsPassThruHci.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/MdeModulePkg/Bus/Ufs/UfsPassThruDxe/UfsPassThruHci.c b/MdeModulePkg/Bus/Ufs/UfsPassThruDxe/UfsPassThruHci.c
index 7c01d57..db70fb1 100644
--- a/MdeModulePkg/Bus/Ufs/UfsPassThruDxe/UfsPassThruHci.c
+++ b/MdeModulePkg/Bus/Ufs/UfsPassThruDxe/UfsPassThruHci.c
@@ -551,6 +551,7 @@ UfsCreateScsiCommandDesc (
Trd->Int = UFS_INTERRUPT_COMMAND;
Trd->Dd = DataDirection;
Trd->Ct = UFS_STORAGE_COMMAND_TYPE;
+ Trd->Ocs = 0x0F;
Trd->UcdBa = (UINT32)RShiftU64 ((UINT64)CmdDescPhyAddr, 7);
Trd->UcdBaU = (UINT32)RShiftU64 ((UINT64)CmdDescPhyAddr, 32);
Trd->RuL = (UINT16)DivU64x32 ((UINT64)ROUNDUP8 (sizeof (UTP_RESPONSE_UPIU)), sizeof (UINT32));
@@ -719,6 +720,7 @@ UfsCreateNopCommandDesc (
Trd->Int = UFS_INTERRUPT_COMMAND;
Trd->Dd = 0x00;
Trd->Ct = UFS_STORAGE_COMMAND_TYPE;
+ Trd->Ocs = 0x0F;
Trd->UcdBa = (UINT32)RShiftU64 ((UINT64)CmdDescPhyAddr, 7);
Trd->UcdBaU = (UINT32)RShiftU64 ((UINT64)CmdDescPhyAddr, 32);
Trd->RuL = (UINT16)DivU64x32 ((UINT64)ROUNDUP8 (sizeof (UTP_NOP_IN_UPIU)), sizeof (UINT32));
--
2.7.4
_______________________________________________
edk2-devel mailing list
edk2-devel@lists.01.org
https://lists.01.org/mailman/listinfo/edk2-devel
next prev parent reply other threads:[~2017-01-06 7:27 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-06 6:52 [PATCH 0/9] enhance UFS Haojian Zhuang
2017-01-06 6:52 ` [PATCH 1/9] Ufs: fix data direction checking Haojian Zhuang
2017-01-06 7:08 ` Tian, Feng
2017-01-06 8:33 ` Haojian Zhuang
2017-01-06 6:52 ` [PATCH 2/9] Ufs: fix to identify 32 bits address mode Haojian Zhuang
2017-01-06 7:10 ` Tian, Feng
2017-01-06 6:52 ` [PATCH 3/9] Ufs: fix the bit in UFS_HC_UTRLDBR_OFFSET register Haojian Zhuang
2017-01-06 7:18 ` Tian, Feng
2017-01-06 6:52 ` [PATCH 4/9] Ufs: fix to set UTRLBA and UTRLBAU register Haojian Zhuang
2017-01-06 8:36 ` Tian, Feng
2017-01-06 9:05 ` Haojian Zhuang
2017-01-09 1:25 ` Tian, Feng
2017-01-06 6:52 ` [PATCH 5/9] Ufs: fix to set PRDT length Haojian Zhuang
2017-01-06 6:52 ` [PATCH 6/9] Ufs: add PhyInit Haojian Zhuang
2017-01-06 7:27 ` Tian, Feng
2017-01-06 8:21 ` Haojian Zhuang
2017-01-06 8:44 ` Tian, Feng
2017-01-06 6:52 ` [PATCH 7/9] Ufs: fix initialize OCS value to 0x0F Haojian Zhuang
2017-01-06 7:26 ` Tian, Feng [this message]
2017-01-06 8:18 ` Haojian Zhuang
2017-01-06 6:52 ` [PATCH 8/9] Ufs: fix to add cache operation Haojian Zhuang
2017-01-06 8:42 ` Tian, Feng
2017-01-06 6:52 ` [PATCH 9/9] ScsiDisk: retry if device detected power failure Haojian Zhuang
2017-01-06 8:22 ` Tian, Feng
2017-01-06 8:31 ` Haojian Zhuang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-list from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=7F1BAD85ADEA444D97065A60D2E97EE5699A5FFA@SHSMSX101.ccr.corp.intel.com \
--to=devel@edk2.groups.io \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox