* [PATCH 1/2] ArmPlatformPkg/PL061: remove duplicated PL061_GPIO_DATA_REG
@ 2017-02-13 7:52 Haojian Zhuang
2017-02-13 7:53 ` [PATCH 2/2] ArmPlatformPkg/PL061Gpio: fix the offset value in Get function Haojian Zhuang
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Haojian Zhuang @ 2017-02-13 7:52 UTC (permalink / raw)
To: leif.lindholm, ard.biesheuvel, edk2-devel; +Cc: Haojian Zhuang
PL061_GPIO_DATA_REG offset is referenced in PL061EffectiveAddress ()
already. So remove the duplicated reference when invoke PL061GetPins ()
or PL061SetPins ().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
index 0e2ea61..ff8bb3b 100644
--- a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
+++ b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
@@ -186,7 +186,7 @@ Get (
return EFI_INVALID_PARAMETER;
}
- if (PL061GetPins (RegisterBase + PL061_GPIO_DATA_REG, Offset)) {
+ if (PL061GetPins (RegisterBase, Offset)) {
*Value = 1;
} else {
*Value = 0;
@@ -239,14 +239,14 @@ Set (
// Set the corresponding direction bit to HIGH for output
MmioOr8 (RegisterBase + PL061_GPIO_DIR_REG, GPIO_PIN_MASK(Offset));
// Set the corresponding data bit to LOW for 0
- PL061SetPins (RegisterBase + PL061_GPIO_DATA_REG, GPIO_PIN_MASK(Offset), 0);
+ PL061SetPins (RegisterBase, GPIO_PIN_MASK(Offset), 0);
break;
case GPIO_MODE_OUTPUT_1:
// Set the corresponding direction bit to HIGH for output
MmioOr8 (RegisterBase + PL061_GPIO_DIR_REG, GPIO_PIN_MASK(Offset));
// Set the corresponding data bit to HIGH for 1
- PL061SetPins (RegisterBase + PL061_GPIO_DATA_REG, GPIO_PIN_MASK(Offset), 0xff);
+ PL061SetPins (RegisterBase, GPIO_PIN_MASK(Offset), 0xff);
break;
default:
@@ -297,7 +297,7 @@ GetMode (
// Check if it is input or output
if (MmioRead8 (RegisterBase + PL061_GPIO_DIR_REG) & GPIO_PIN_MASK(Offset)) {
// Pin set to output
- if (PL061GetPins (RegisterBase + PL061_GPIO_DATA_REG, GPIO_PIN_MASK(Offset))) {
+ if (PL061GetPins (RegisterBase, GPIO_PIN_MASK(Offset))) {
*Mode = GPIO_MODE_OUTPUT_1;
} else {
*Mode = GPIO_MODE_OUTPUT_0;
--
2.7.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] ArmPlatformPkg/PL061Gpio: fix the offset value in Get function
2017-02-13 7:52 [PATCH 1/2] ArmPlatformPkg/PL061: remove duplicated PL061_GPIO_DATA_REG Haojian Zhuang
@ 2017-02-13 7:53 ` Haojian Zhuang
2017-02-13 12:59 ` Haojian Zhuang
2017-02-16 11:34 ` Ard Biesheuvel
2017-02-13 12:59 ` [PATCH 1/2] ArmPlatformPkg/PL061: remove duplicated PL061_GPIO_DATA_REG Haojian Zhuang
2017-02-16 11:23 ` Ard Biesheuvel
2 siblings, 2 replies; 6+ messages in thread
From: Haojian Zhuang @ 2017-02-13 7:53 UTC (permalink / raw)
To: leif.lindholm, ard.biesheuvel, edk2-devel; +Cc: Haojian Zhuang
When call PL061GetPins() or PL061SetPins(), should use GPIO_PIN_MASK(offset)
as parameter, not offset.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
index ff8bb3b..81b9f6d 100644
--- a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
+++ b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
@@ -186,7 +186,7 @@ Get (
return EFI_INVALID_PARAMETER;
}
- if (PL061GetPins (RegisterBase, Offset)) {
+ if (PL061GetPins (RegisterBase, GPIO_PIN_MASK(Offset))) {
*Value = 1;
} else {
*Value = 0;
--
2.7.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] ArmPlatformPkg/PL061: remove duplicated PL061_GPIO_DATA_REG
2017-02-13 7:52 [PATCH 1/2] ArmPlatformPkg/PL061: remove duplicated PL061_GPIO_DATA_REG Haojian Zhuang
2017-02-13 7:53 ` [PATCH 2/2] ArmPlatformPkg/PL061Gpio: fix the offset value in Get function Haojian Zhuang
@ 2017-02-13 12:59 ` Haojian Zhuang
2017-02-16 11:23 ` Ard Biesheuvel
2 siblings, 0 replies; 6+ messages in thread
From: Haojian Zhuang @ 2017-02-13 12:59 UTC (permalink / raw)
To: Leif Lindholm, edk2-devel@lists.01.org, Ard Biesheuvel
On 13 February 2017 at 15:52, Haojian Zhuang <haojian.zhuang@linaro.org> wrote:
> PL061_GPIO_DATA_REG offset is referenced in PL061EffectiveAddress ()
> already. So remove the duplicated reference when invoke PL061GetPins ()
> or PL061SetPins ().
>
> Contributed-under: TianoCore Contribution Agreement 1.0
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
> ---
> ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c | 8 ++++----
> 1 file changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> index 0e2ea61..ff8bb3b 100644
> --- a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> +++ b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> @@ -186,7 +186,7 @@ Get (
> return EFI_INVALID_PARAMETER;
> }
>
> - if (PL061GetPins (RegisterBase + PL061_GPIO_DATA_REG, Offset)) {
> + if (PL061GetPins (RegisterBase, Offset)) {
> *Value = 1;
> } else {
> *Value = 0;
> @@ -239,14 +239,14 @@ Set (
> // Set the corresponding direction bit to HIGH for output
> MmioOr8 (RegisterBase + PL061_GPIO_DIR_REG, GPIO_PIN_MASK(Offset));
> // Set the corresponding data bit to LOW for 0
> - PL061SetPins (RegisterBase + PL061_GPIO_DATA_REG, GPIO_PIN_MASK(Offset), 0);
> + PL061SetPins (RegisterBase, GPIO_PIN_MASK(Offset), 0);
> break;
>
> case GPIO_MODE_OUTPUT_1:
> // Set the corresponding direction bit to HIGH for output
> MmioOr8 (RegisterBase + PL061_GPIO_DIR_REG, GPIO_PIN_MASK(Offset));
> // Set the corresponding data bit to HIGH for 1
> - PL061SetPins (RegisterBase + PL061_GPIO_DATA_REG, GPIO_PIN_MASK(Offset), 0xff);
> + PL061SetPins (RegisterBase, GPIO_PIN_MASK(Offset), 0xff);
> break;
>
> default:
> @@ -297,7 +297,7 @@ GetMode (
> // Check if it is input or output
> if (MmioRead8 (RegisterBase + PL061_GPIO_DIR_REG) & GPIO_PIN_MASK(Offset)) {
> // Pin set to output
> - if (PL061GetPins (RegisterBase + PL061_GPIO_DATA_REG, GPIO_PIN_MASK(Offset))) {
> + if (PL061GetPins (RegisterBase, GPIO_PIN_MASK(Offset))) {
> *Mode = GPIO_MODE_OUTPUT_1;
> } else {
> *Mode = GPIO_MODE_OUTPUT_0;
> --
> 2.7.4
>
Correct Ard's email address.
Regards
Haojian
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ArmPlatformPkg/PL061Gpio: fix the offset value in Get function
2017-02-13 7:53 ` [PATCH 2/2] ArmPlatformPkg/PL061Gpio: fix the offset value in Get function Haojian Zhuang
@ 2017-02-13 12:59 ` Haojian Zhuang
2017-02-16 11:34 ` Ard Biesheuvel
1 sibling, 0 replies; 6+ messages in thread
From: Haojian Zhuang @ 2017-02-13 12:59 UTC (permalink / raw)
To: Leif Lindholm, edk2-devel@lists.01.org, Ard Biesheuvel
On 13 February 2017 at 15:53, Haojian Zhuang <haojian.zhuang@linaro.org> wrote:
> When call PL061GetPins() or PL061SetPins(), should use GPIO_PIN_MASK(offset)
> as parameter, not offset.
>
> Contributed-under: TianoCore Contribution Agreement 1.0
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
> ---
> ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> index ff8bb3b..81b9f6d 100644
> --- a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> +++ b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> @@ -186,7 +186,7 @@ Get (
> return EFI_INVALID_PARAMETER;
> }
>
> - if (PL061GetPins (RegisterBase, Offset)) {
> + if (PL061GetPins (RegisterBase, GPIO_PIN_MASK(Offset))) {
> *Value = 1;
> } else {
> *Value = 0;
> --
> 2.7.4
>
Correct Ard's email address.
Regards
Haojian
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] ArmPlatformPkg/PL061: remove duplicated PL061_GPIO_DATA_REG
2017-02-13 7:52 [PATCH 1/2] ArmPlatformPkg/PL061: remove duplicated PL061_GPIO_DATA_REG Haojian Zhuang
2017-02-13 7:53 ` [PATCH 2/2] ArmPlatformPkg/PL061Gpio: fix the offset value in Get function Haojian Zhuang
2017-02-13 12:59 ` [PATCH 1/2] ArmPlatformPkg/PL061: remove duplicated PL061_GPIO_DATA_REG Haojian Zhuang
@ 2017-02-16 11:23 ` Ard Biesheuvel
2 siblings, 0 replies; 6+ messages in thread
From: Ard Biesheuvel @ 2017-02-16 11:23 UTC (permalink / raw)
To: Haojian Zhuang; +Cc: Leif Lindholm, edk2-devel@lists.01.org
On 13 February 2017 at 07:52, Haojian Zhuang <haojian.zhuang@linaro.org> wrote:
> PL061_GPIO_DATA_REG offset is referenced in PL061EffectiveAddress ()
> already. So remove the duplicated reference when invoke PL061GetPins ()
> or PL061SetPins ().
>
> Contributed-under: TianoCore Contribution Agreement 1.0
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
> ---
> ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c | 8 ++++----
> 1 file changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> index 0e2ea61..ff8bb3b 100644
> --- a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> +++ b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> @@ -186,7 +186,7 @@ Get (
> return EFI_INVALID_PARAMETER;
> }
>
> - if (PL061GetPins (RegisterBase + PL061_GPIO_DATA_REG, Offset)) {
> + if (PL061GetPins (RegisterBase, Offset)) {
> *Value = 1;
> } else {
> *Value = 0;
> @@ -239,14 +239,14 @@ Set (
> // Set the corresponding direction bit to HIGH for output
> MmioOr8 (RegisterBase + PL061_GPIO_DIR_REG, GPIO_PIN_MASK(Offset));
> // Set the corresponding data bit to LOW for 0
> - PL061SetPins (RegisterBase + PL061_GPIO_DATA_REG, GPIO_PIN_MASK(Offset), 0);
> + PL061SetPins (RegisterBase, GPIO_PIN_MASK(Offset), 0);
> break;
>
> case GPIO_MODE_OUTPUT_1:
> // Set the corresponding direction bit to HIGH for output
> MmioOr8 (RegisterBase + PL061_GPIO_DIR_REG, GPIO_PIN_MASK(Offset));
> // Set the corresponding data bit to HIGH for 1
> - PL061SetPins (RegisterBase + PL061_GPIO_DATA_REG, GPIO_PIN_MASK(Offset), 0xff);
> + PL061SetPins (RegisterBase, GPIO_PIN_MASK(Offset), 0xff);
> break;
>
> default:
> @@ -297,7 +297,7 @@ GetMode (
> // Check if it is input or output
> if (MmioRead8 (RegisterBase + PL061_GPIO_DIR_REG) & GPIO_PIN_MASK(Offset)) {
> // Pin set to output
> - if (PL061GetPins (RegisterBase + PL061_GPIO_DATA_REG, GPIO_PIN_MASK(Offset))) {
> + if (PL061GetPins (RegisterBase, GPIO_PIN_MASK(Offset))) {
> *Mode = GPIO_MODE_OUTPUT_1;
> } else {
> *Mode = GPIO_MODE_OUTPUT_0;
> --
> 2.7.4
>
> _______________________________________________
> edk2-devel mailing list
> edk2-devel@lists.01.org
> https://lists.01.org/mailman/listinfo/edk2-devel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ArmPlatformPkg/PL061Gpio: fix the offset value in Get function
2017-02-13 7:53 ` [PATCH 2/2] ArmPlatformPkg/PL061Gpio: fix the offset value in Get function Haojian Zhuang
2017-02-13 12:59 ` Haojian Zhuang
@ 2017-02-16 11:34 ` Ard Biesheuvel
1 sibling, 0 replies; 6+ messages in thread
From: Ard Biesheuvel @ 2017-02-16 11:34 UTC (permalink / raw)
To: Haojian Zhuang; +Cc: Leif Lindholm, edk2-devel@lists.01.org
On 13 February 2017 at 07:53, Haojian Zhuang <haojian.zhuang@linaro.org> wrote:
> When call PL061GetPins() or PL061SetPins(), should use GPIO_PIN_MASK(offset)
> as parameter, not offset.
>
> Contributed-under: TianoCore Contribution Agreement 1.0
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Pushed as
d164a0e31bf8 ArmPlatformPkg/PL061: remove duplicated PL061_GPIO_DATA_REG
d176bb3c5c28 ArmPlatformPkg/PL061Gpio: fix the offset value in Get function
> ---
> ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> index ff8bb3b..81b9f6d 100644
> --- a/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> +++ b/ArmPlatformPkg/Drivers/PL061GpioDxe/PL061Gpio.c
> @@ -186,7 +186,7 @@ Get (
> return EFI_INVALID_PARAMETER;
> }
>
> - if (PL061GetPins (RegisterBase, Offset)) {
> + if (PL061GetPins (RegisterBase, GPIO_PIN_MASK(Offset))) {
> *Value = 1;
> } else {
> *Value = 0;
> --
> 2.7.4
>
> _______________________________________________
> edk2-devel mailing list
> edk2-devel@lists.01.org
> https://lists.01.org/mailman/listinfo/edk2-devel
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2017-02-16 11:34 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2017-02-13 7:52 [PATCH 1/2] ArmPlatformPkg/PL061: remove duplicated PL061_GPIO_DATA_REG Haojian Zhuang
2017-02-13 7:53 ` [PATCH 2/2] ArmPlatformPkg/PL061Gpio: fix the offset value in Get function Haojian Zhuang
2017-02-13 12:59 ` Haojian Zhuang
2017-02-16 11:34 ` Ard Biesheuvel
2017-02-13 12:59 ` [PATCH 1/2] ArmPlatformPkg/PL061: remove duplicated PL061_GPIO_DATA_REG Haojian Zhuang
2017-02-16 11:23 ` Ard Biesheuvel
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox