From: "Michael D Kinney" <michael.d.kinney@intel.com>
To: "Warkentin, Andrei" <andrei.warkentin@intel.com>,
"devel@edk2.groups.io" <devel@edk2.groups.io>
Cc: "Gao, Liming" <gaoliming@byosoft.com.cn>,
"Liu, Zhiguang" <zhiguang.liu@intel.com>,
"Kinney, Michael D" <michael.d.kinney@intel.com>
Subject: Re: [PATCH v5 2/3] MdePkg: add SBI-based SerialPortLib for RISC-V
Date: Mon, 27 Mar 2023 16:32:18 +0000 [thread overview]
Message-ID: <CO1PR11MB4929D85F96C3D7963DD0A3E6D28B9@CO1PR11MB4929.namprd11.prod.outlook.com> (raw)
In-Reply-To: <PH8PR11MB685658DC8FD0594DACCA330083BD9@PH8PR11MB6856.namprd11.prod.outlook.com>
I think that would still be called Sec. Are there any issues with using Sec prefix?
Mike
> -----Original Message-----
> From: Warkentin, Andrei <andrei.warkentin@intel.com>
> Sent: Thursday, March 16, 2023 10:45 PM
> To: Kinney, Michael D <michael.d.kinney@intel.com>; devel@edk2.groups.io
> Cc: Gao, Liming <gaoliming@byosoft.com.cn>; Liu, Zhiguang <zhiguang.liu@intel.com>
> Subject: RE: [PATCH v5 2/3] MdePkg: add SBI-based SerialPortLib for RISC-V
>
> PrePi refers to a SEC-like stage in a Tiano implementation that skips the PEI stage. Reasons for skipping PEI usually center around
> memory initialization being done at an earlier stage of firmware initialization - for example, prior or part of TF-A firmware on
> AArch64 or prior or part of SBI implementation on RISC-V.
>
> E.g. ArmVirtPkg/PrePi and OvmfPkg/RiscVVirt/Sec. The later is not a "SEC" in the send of handing off to PeiCore, but instead hands
> off to DxeCore.
>
> There is no base type for PrePi. The type is still SEC. But it a) assumes RAM is available b) builds HOBs and hands-off to DXE.
>
> The name has been around for at least half a decade now and making it a part of the SerialPortLib component name is important as it
> signifies the scenario where the code can apply.
>
> A
>
> -----Original Message-----
> From: Kinney, Michael D <michael.d.kinney@intel.com>
> Sent: Friday, March 17, 2023 12:01 AM
> To: Warkentin, Andrei <andrei.warkentin@intel.com>; devel@edk2.groups.io
> Cc: Gao, Liming <gaoliming@byosoft.com.cn>; Liu, Zhiguang <zhiguang.liu@intel.com>; Kinney, Michael D <michael.d.kinney@intel.com>
> Subject: RE: [PATCH v5 2/3] MdePkg: add SBI-based SerialPortLib for RISC-V
>
> What is the definition of "PrePI"? That is not a prefix I have seen used before.
>
> Mike
>
> > -----Original Message-----
> > From: Warkentin, Andrei <andrei.warkentin@intel.com>
> > Sent: Thursday, March 16, 2023 9:53 PM
> > To: devel@edk2.groups.io
> > Cc: Kinney, Michael D <michael.d.kinney@intel.com>; Gao, Liming
> > <gaoliming@byosoft.com.cn>; Liu, Zhiguang <zhiguang.liu@intel.com>
> > Subject: RE: [PATCH v5 2/3] MdePkg: add SBI-based SerialPortLib for
> > RISC-V
> >
> > Hi folks,
> >
> > Can I get a review for the changes to MdePkg.dsc to include the new
> > libs on RISC-V? That's the minor thing preventing this patch set from being merged 😊.
> >
> > A
> >
> > -----Original Message-----
> > From: Warkentin, Andrei <andrei.warkentin@intel.com>
> > Sent: Friday, March 10, 2023 11:05 AM
> > To: devel@edk2.groups.io
> > Cc: Warkentin, Andrei <andrei.warkentin@intel.com>; Daniel Schaefer
> > <git@danielschaefer.me>; Sunil V L <sunilvl@ventanamicro.com>; Kinney,
> > Michael D <michael.d.kinney@intel.com>; Gao, Liming
> > <gaoliming@byosoft.com.cn>; Liu, Zhiguang <zhiguang.liu@intel.com>;
> > Gerd Hoffmann <kraxel@redhat.com>
> > Subject: [PATCH v5 2/3] MdePkg: add SBI-based SerialPortLib for RISC-V
> >
> > These are implementations of SerialPortLib using SBI console services.
> > - SecPeiRiscVSerialPortLibSbi is appropriate for SEC/PEI (XIP)
> > environments
> > - PrePiDxeRiscVSerialPortLibSbi is appropriate for PrePI/DXE
> > environments
> >
> > Tested with:
> > - Qemu RiscVVirt (non-DBCN case, backed by UART)
> > - TinyEMU + RiscVVirt (non-DBCN case, HTIF)
> > - TinyEMU + RiscVVirt (DBCN case, HTIF)
> >
> > Cc: Daniel Schaefer <git@danielschaefer.me>
> > Cc: Sunil V L <sunilvl@ventanamicro.com>
> > Cc: Michael D Kinney <michael.d.kinney@intel.com>
> > Cc: Liming Gao <gaoliming@byosoft.com.cn>
> > Cc: Zhiguang Liu <zhiguang.liu@intel.com>
> > Acked-by: Gerd Hoffmann <kraxel@redhat.com>
> > Signed-off-by: Andrei Warkentin <andrei.warkentin@intel.com>
> > ---
> > MdePkg/MdePkg.dsc | 2 +
> > MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerialPortLibSbi.inf | 36 +++
> > MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPortLibSbi.inf | 39 +++
> > MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerialPortLibSbi.c | 288 ++++++++++++++++++++
> > MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPortLibSbi.c | 233 ++++++++++++++++
> > MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerialPortLibSbi.uni | 16 ++
> > MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPortLibSbi.uni | 16 ++
> > 7 files changed, 630 insertions(+)
> >
> > diff --git a/MdePkg/MdePkg.dsc b/MdePkg/MdePkg.dsc index
> > 0ac7618b4623..fb31349042fb 100644
> > --- a/MdePkg/MdePkg.dsc
> > +++ b/MdePkg/MdePkg.dsc
> > @@ -192,5 +192,7 @@ [Components.ARM, Components.AARCH64]
> >
> > [Components.RISCV64]
> > MdePkg/Library/BaseRiscVSbiLib/BaseRiscVSbiLib.inf
> > +
> > + MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPortLibS
> > + bi
> > + .inf
> > + MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerialPort
> > + Li
> > + bSbi.inf
> >
> > [BuildOptions]
> > diff --git
> > a/MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerialPort
> > LibSbi.inf
> > b/MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerialPort
> > LibSbi.inf
> > new file mode 100644
> > index 000000000000..1d8544756bb9
> > --- /dev/null
> > +++ b/MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerial
> > +++ Po
> > +++ rtLibSbi.inf
> > @@ -0,0 +1,36 @@
> > +## @file
> > +# Serial Port Library backed by SBI console.
> > +#
> > +# Meant for PrePi and DXE environments (where globals are allowed).
> > +See # SecPeiSerialPortLibRiscVSbi for a reduced variant appropriate
> > +for SEC # and PEI (XIP) environments.
> > +#
> > +# Copyright (c) 2023, Intel Corporation. All rights reserved.<BR> #
> > +#
> > +SPDX-License-Identifier: BSD-2-Clause-Patent # # ##
> > +
> > +[Defines]
> > + INF_VERSION = 0x0001001B
> > + BASE_NAME = PrePiDxeRiscVSerialPortLibSbi
> > + MODULE_UNI_FILE = PrePiDxeRiscVSerialPortLibSbi.uni
> > + FILE_GUID = 872af743-ab56-45b4-a065-602567f4820c
> > + MODULE_TYPE = BASE
> > + VERSION_STRING = 1.0
> > + LIBRARY_CLASS = SerialPortLib | SEC DXE_CORE DXE_DRIVER DXE_RUNTIME_DRIVER UEFI_DRIVER UEFI_APPLICATION
> > +
> > +
> > +#
> > +# VALID_ARCHITECTURES = RISCV64
> > +#
> > +
> > +[Sources]
> > + PrePiDxeRiscVSerialPortLibSbi.c
> > +
> > +[Packages]
> > + MdePkg/MdePkg.dec
> > +
> > +[LibraryClasses]
> > + RiscVSbiLib
> > diff --git
> > a/MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPortLibS
> > bi.inf
> > b/MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPortLibS
> > bi.inf
> > new file mode 100644
> > index 000000000000..7bc7cd47c11c
> > --- /dev/null
> > +++ b/MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPort
> > +++ Li
> > +++ bSbi.inf
> > @@ -0,0 +1,39 @@
> > +## @file
> > +# Serial Port Library backed by SBI console.
> > +#
> > +# Meant for SEC and PEI (XIP) environments.
> > +#
> > +# Due to limitations of SBI console interface and XIP environments #
> > +(on use of globals), this library instance does not implement reading
> > +# and polling the serial port. See PrePiDxeSerialPortLibRiscVSbi for
> > +# the full-featured variant meant for PrePi and DXE environments.
> > +#
> > +# Copyright (c) 2023, Intel Corporation. All rights reserved.<BR> #
> > +#
> > +SPDX-License-Identifier: BSD-2-Clause-Patent # # ##
> > +
> > +[Defines]
> > + INF_VERSION = 0x0001001B
> > + BASE_NAME = SecPeiRiscVSerialPortLibSbi
> > + MODULE_UNI_FILE = SecPeiRiscVSerialPortLibSbi.uni
> > + FILE_GUID = 639fad38-4bfd-4eb9-9f09-e97c7947d480
> > + MODULE_TYPE = BASE
> > + VERSION_STRING = 1.0
> > + LIBRARY_CLASS = SerialPortLib | SEC PEI_CORE PEIM
> > +
> > +
> > +#
> > +# VALID_ARCHITECTURES = RISCV64
> > +#
> > +
> > +[Sources]
> > + SecPeiRiscVSerialPortLibSbi.c
> > +
> > +[Packages]
> > + MdePkg/MdePkg.dec
> > +
> > +[LibraryClasses]
> > + RiscVSbiLib
> > diff --git
> > a/MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerialPort
> > LibSbi.c
> > b/MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerialPort
> > LibSbi.c
> > new file mode 100644
> > index 000000000000..058a6573ef2d
> > --- /dev/null
> > +++ b/MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerial
> > +++ Po
> > +++ rtLibSbi.c
> > @@ -0,0 +1,288 @@
> > +/** @file
> > + Serial Port Library backed by SBI console.
> > +
> > + Meant for PrePi and DXE environments (where globals are allowed).
> > + See SecPeiSerialPortLibRiscVSbi for a reduced variant appropriate
> > + for SEC and PEI (XIP) environments.
> > +
> > + Copyright (c) 2023, Intel Corporation. All rights reserved.<BR>
> > + SPDX-License-Identifier: BSD-2-Clause-Patent
> > +
> > +**/
> > +
> > +#include <Base.h>
> > +#include <Library/SerialPortLib.h>
> > +#include <Library/BaseRiscVSbiLib.h>
> > +
> > +STATIC BOOLEAN mHaveDbcn = FALSE;
> > +STATIC BOOLEAN mHaveLegacyPutchar = FALSE; STATIC BOOLEAN
> > +mHaveLegacyGetchar = FALSE;
> > +STATIC INT64 mLastGetChar = -1;
> > +
> > +/**
> > + Initialize the serial device hardware.
> > +
> > + If no initialization is required, then return RETURN_SUCCESS.
> > + If the serial device was successfully initialized, then return RETURN_SUCCESS.
> > + If the serial device could not be initialized, then return RETURN_DEVICE_ERROR.
> > +
> > + @retval RETURN_SUCCESS The serial device was initialized.
> > + @retval RETURN_DEVICE_ERROR The serial device could not be initialized.
> > +
> > +**/
> > +RETURN_STATUS
> > +EFIAPI
> > +SerialPortInitialize (
> > + VOID
> > + )
> > +{
> > + SBI_RET Ret;
> > +
> > + Ret = SbiCall (SBI_EXT_BASE, SBI_EXT_BASE_PROBE_EXT, 1,
> > + SBI_EXT_DBCN); if ((TranslateError (Ret.Error) == EFI_SUCCESS) &&
> > + (Ret.Value != 0))
> > + {
> > + mHaveDbcn = TRUE;
> > + } else {
> > + Ret = SbiCall (SBI_EXT_BASE, SBI_EXT_BASE_PROBE_EXT, 1, SBI_EXT_0_1_CONSOLE_PUTCHAR);
> > + if ((TranslateError (Ret.Error) == EFI_SUCCESS) &&
> > + (Ret.Value != 0))
> > + {
> > + mHaveLegacyPutchar = TRUE;
> > + }
> > +
> > + Ret = SbiCall (SBI_EXT_BASE, SBI_EXT_BASE_PROBE_EXT, 1, SBI_EXT_0_1_CONSOLE_GETCHAR);
> > + if ((TranslateError (Ret.Error) == EFI_SUCCESS) &&
> > + (Ret.Value != 0))
> > + {
> > + mHaveLegacyGetchar = TRUE;
> > + }
> > + }
> > +
> > + return RETURN_SUCCESS;
> > +}
> > +
> > +/**
> > + Write data from buffer to serial device.
> > +
> > + Writes NumberOfBytes data bytes from Buffer to the serial device.
> > + The number of bytes actually written to the serial device is returned.
> > + If the return value is less than NumberOfBytes, then the write operation failed.
> > + If Buffer is NULL, then ASSERT().
> > + If NumberOfBytes is zero, then return 0.
> > +
> > + @param Buffer The pointer to the data buffer to be written.
> > + @param NumberOfBytes The number of bytes to written to the serial device.
> > +
> > + @retval 0 NumberOfBytes is 0.
> > + @retval >0 The number of bytes written to the serial device.
> > + If this value is less than NumberOfBytes, then the write operation failed.
> > +
> > +**/
> > +UINTN
> > +EFIAPI
> > +SerialPortWrite (
> > + IN UINT8 *Buffer,
> > + IN UINTN NumberOfBytes
> > + )
> > +{
> > + UINTN Index;
> > +
> > + if (mHaveDbcn) {
> > + SBI_RET Ret;
> > + Ret = SbiCall (
> > + SBI_EXT_DBCN,
> > + SBI_EXT_DBCN_WRITE,
> > + 3,
> > + NumberOfBytes,
> > + ((UINTN)Buffer),
> > + 0
> > + );
> > + if (TranslateError (Ret.Error) != EFI_SUCCESS) {
> > + return 0;
> > + }
> > +
> > + return Ret.Value;
> > + } else if (mHaveLegacyPutchar) {
> > + for (Index = 0; Index < NumberOfBytes; Index++) {
> > + SbiCall (SBI_EXT_0_1_CONSOLE_PUTCHAR, 0, 1, Buffer[Index]);
> > + }
> > +
> > + return Index;
> > + }
> > +
> > + /*
> > + * Neither DBCN or legacy extension were present.
> > + */
> > + return NumberOfBytes;
> > +}
> > +
> > +/**
> > + Read data from serial device and save the datas in buffer.
> > +
> > + Reads NumberOfBytes data bytes from a serial device into the buffer
> > + specified by Buffer. The number of bytes actually read is returned.
> > + If the return value is less than NumberOfBytes, then the rest operation failed.
> > + If Buffer is NULL, then ASSERT().
> > + If NumberOfBytes is zero, then return 0.
> > +
> > + @param Buffer The pointer to the data buffer to store the data read from the serial device.
> > + @param NumberOfBytes The number of bytes which will be read.
> > +
> > + @retval 0 Read data failed; No data is to be read.
> > + @retval >0 The actual number of bytes read from serial device.
> > +
> > +**/
> > +UINTN
> > +EFIAPI
> > +SerialPortRead (
> > + OUT UINT8 *Buffer,
> > + IN UINTN NumberOfBytes
> > + )
> > +{
> > + UINTN Index;
> > +
> > + Index = 0;
> > + while ((Index < NumberOfBytes) && SerialPortPoll ()) {
> > + Buffer[Index++] = (UINT8)mLastGetChar;
> > + mLastGetChar = -1;
> > + }
> > +
> > + return Index;
> > +}
> > +
> > +/**
> > + Polls a serial device to see if there is any data waiting to be read.
> > +
> > + Polls a serial device to see if there is any data waiting to be read.
> > + If there is data waiting to be read from the serial device, then TRUE is returned.
> > + If there is no data waiting to be read from the serial device, then FALSE is returned.
> > +
> > + @retval TRUE Data is waiting to be read from the serial device.
> > + @retval FALSE There is no data waiting to be read from the serial device.
> > +
> > +**/
> > +BOOLEAN
> > +EFIAPI
> > +SerialPortPoll (
> > + VOID
> > + )
> > +{
> > + /*
> > + * Careful. OpenSBI with HTIF console will return -1 followed by -2
> > + * if there is no character received. So just check for values >= 0.
> > + */
> > +
> > + if (mLastGetChar >= 0) {
> > + return TRUE;
> > + }
> > +
> > + if (mHaveDbcn) {
> > + UINT8 Buffer;
> > + SBI_RET Ret;
> > +
> > + Ret = SbiCall (
> > + SBI_EXT_DBCN,
> > + SBI_EXT_DBCN_READ,
> > + 3,
> > + 1,
> > + ((UINTN)&Buffer),
> > + 0
> > + );
> > + if ((TranslateError (Ret.Error) == EFI_SUCCESS) &&
> > + (Ret.Value == 1))
> > + {
> > + mLastGetChar = Buffer;
> > + }
> > + } else if (mHaveLegacyGetchar) {
> > + mLastGetChar = (INT64)SbiCall (SBI_EXT_0_1_CONSOLE_GETCHAR, 0,
> > + 0).Error; }
> > +
> > + return mLastGetChar >= 0;
> > +}
> > +
> > +/**
> > + Sets the control bits on a serial device.
> > +
> > + @param Control Sets the bits of Control that are settable.
> > +
> > + @retval RETURN_SUCCESS The new control bits were set on the serial device.
> > + @retval RETURN_UNSUPPORTED The serial device does not support this operation.
> > + @retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
> > +
> > +**/
> > +RETURN_STATUS
> > +EFIAPI
> > +SerialPortSetControl (
> > + IN UINT32 Control
> > + )
> > +{
> > + return RETURN_SUCCESS;
> > +}
> > +
> > +/**
> > + Retrieve the status of the control bits on a serial device.
> > +
> > + @param Control A pointer to return the current control signals from the serial device.
> > +
> > + @retval RETURN_SUCCESS The control bits were read from the serial device.
> > + @retval RETURN_UNSUPPORTED The serial device does not support this operation.
> > + @retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
> > +
> > +**/
> > +RETURN_STATUS
> > +EFIAPI
> > +SerialPortGetControl (
> > + OUT UINT32 *Control
> > + )
> > +{
> > + *Control = 0;
> > + return RETURN_SUCCESS;
> > +}
> > +
> > +/**
> > + Sets the baud rate, receive FIFO depth, transmit/receice time out,
> > +parity,
> > + data bits, and stop bits on a serial device.
> > +
> > + @param BaudRate The requested baud rate. A BaudRate value of 0 will use the
> > + device's default interface speed.
> > + On output, the value actually set.
> > + @param ReveiveFifoDepth The requested depth of the FIFO on the receive side of the
> > + serial interface. A ReceiveFifoDepth value of 0 will use
> > + the device's default FIFO depth.
> > + On output, the value actually set.
> > + @param Timeout The requested time out for a single character in microseconds.
> > + This timeout applies to both the transmit and receive side of the
> > + interface. A Timeout value of 0 will use the device's default time
> > + out value.
> > + On output, the value actually set.
> > + @param Parity The type of parity to use on this serial device. A Parity value of
> > + DefaultParity will use the device's default parity value.
> > + On output, the value actually set.
> > + @param DataBits The number of data bits to use on the serial device. A DataBits
> > + vaule of 0 will use the device's default data bit setting.
> > + On output, the value actually set.
> > + @param StopBits The number of stop bits to use on this serial device. A StopBits
> > + value of DefaultStopBits will use the device's default number of
> > + stop bits.
> > + On output, the value actually set.
> > +
> > + @retval RETURN_SUCCESS The new attributes were set on the serial device.
> > + @retval RETURN_UNSUPPORTED The serial device does not support this operation.
> > + @retval RETURN_INVALID_PARAMETER One or more of the attributes has an unsupported value.
> > + @retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
> > +
> > +**/
> > +RETURN_STATUS
> > +EFIAPI
> > +SerialPortSetAttributes (
> > + IN OUT UINT64 *BaudRate,
> > + IN OUT UINT32 *ReceiveFifoDepth,
> > + IN OUT UINT32 *Timeout,
> > + IN OUT EFI_PARITY_TYPE *Parity,
> > + IN OUT UINT8 *DataBits,
> > + IN OUT EFI_STOP_BITS_TYPE *StopBits
> > + )
> > +{
> > + return RETURN_SUCCESS;
> > +}
> > diff --git
> > a/MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPortLibS
> > bi.c
> > b/MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPortLibS
> > bi.c
> > new file mode 100644
> > index 000000000000..0ad5931be3ae
> > --- /dev/null
> > +++ b/MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPort
> > +++ Li
> > +++ bSbi.c
> > @@ -0,0 +1,233 @@
> > +/** @file
> > + Serial Port Library backed by SBI console.
> > +
> > + Meant for SEC and PEI (XIP) environments.
> > +
> > + Due to limitations of SBI console interface and XIP environments
> > + (on use of globals), this library instance does not implement
> > + reading and polling the serial port. See
> > + PrePiDxeSerialPortLibRiscVSbi for the full-featured variant meant for PrePi and DXE environments.
> > +
> > + Copyright (c) 2023, Intel Corporation. All rights reserved.<BR>
> > + SPDX-License-Identifier: BSD-2-Clause-Patent
> > +
> > +**/
> > +
> > +#include <Base.h>
> > +#include <Library/SerialPortLib.h>
> > +#include <Library/BaseRiscVSbiLib.h>
> > +
> > +/**
> > + Initialize the serial device hardware.
> > +
> > + If no initialization is required, then return RETURN_SUCCESS.
> > + If the serial device was successfully initialized, then return RETURN_SUCCESS.
> > + If the serial device could not be initialized, then return RETURN_DEVICE_ERROR.
> > +
> > + @retval RETURN_SUCCESS The serial device was initialized.
> > + @retval RETURN_DEVICE_ERROR The serial device could not be initialized.
> > +
> > +**/
> > +RETURN_STATUS
> > +EFIAPI
> > +SerialPortInitialize (
> > + VOID
> > + )
> > +{
> > + return RETURN_SUCCESS;
> > +}
> > +
> > +/**
> > + Write data from buffer to serial device.
> > +
> > + Writes NumberOfBytes data bytes from Buffer to the serial device.
> > + The number of bytes actually written to the serial device is returned.
> > + If the return value is less than NumberOfBytes, then the write operation failed.
> > + If Buffer is NULL, then ASSERT().
> > + If NumberOfBytes is zero, then return 0.
> > +
> > + @param Buffer The pointer to the data buffer to be written.
> > + @param NumberOfBytes The number of bytes to written to the serial device.
> > +
> > + @retval 0 NumberOfBytes is 0.
> > + @retval >0 The number of bytes written to the serial device.
> > + If this value is less than NumberOfBytes, then the write operation failed.
> > +
> > +**/
> > +UINTN
> > +EFIAPI
> > +SerialPortWrite (
> > + IN UINT8 *Buffer,
> > + IN UINTN NumberOfBytes
> > + )
> > +{
> > + SBI_RET Ret;
> > + UINTN Index;
> > +
> > + Ret = SbiCall (SBI_EXT_BASE, SBI_EXT_BASE_PROBE_EXT, 1,
> > + SBI_EXT_DBCN); if ((TranslateError (Ret.Error) == EFI_SUCCESS) &&
> > + (Ret.Value != 0))
> > + {
> > + Ret = SbiCall (
> > + SBI_EXT_DBCN,
> > + SBI_EXT_DBCN_WRITE,
> > + 3,
> > + NumberOfBytes,
> > + ((UINTN)Buffer),
> > + 0
> > + );
> > + if (TranslateError (Ret.Error) != EFI_SUCCESS) {
> > + return 0;
> > + }
> > +
> > + return Ret.Value;
> > + }
> > +
> > + Ret = SbiCall (SBI_EXT_BASE, SBI_EXT_BASE_PROBE_EXT, 1,
> > + SBI_EXT_0_1_CONSOLE_PUTCHAR); if ((TranslateError (Ret.Error) == EFI_SUCCESS) &&
> > + (Ret.Value != 0))
> > + {
> > + for (Index = 0; Index < NumberOfBytes; Index++) {
> > + SbiCall (SBI_EXT_0_1_CONSOLE_PUTCHAR, 0, 1, Buffer[Index]);
> > + }
> > +
> > + return Index;
> > + }
> > +
> > + /*
> > + * Neither DBCN or legacy extension were present.
> > + */
> > + return NumberOfBytes;
> > +}
> > +
> > +/**
> > + Read data from serial device and save the datas in buffer.
> > +
> > + Reads NumberOfBytes data bytes from a serial device into the buffer
> > + specified by Buffer. The number of bytes actually read is returned.
> > + If the return value is less than NumberOfBytes, then the rest operation failed.
> > + If Buffer is NULL, then ASSERT().
> > + If NumberOfBytes is zero, then return 0.
> > +
> > + @param Buffer The pointer to the data buffer to store the data read from the serial device.
> > + @param NumberOfBytes The number of bytes which will be read.
> > +
> > + @retval 0 Read data failed; No data is to be read.
> > + @retval >0 The actual number of bytes read from serial device.
> > +
> > +**/
> > +UINTN
> > +EFIAPI
> > +SerialPortRead (
> > + OUT UINT8 *Buffer,
> > + IN UINTN NumberOfBytes
> > + )
> > +{
> > + return 0;
> > +}
> > +
> > +/**
> > + Polls a serial device to see if there is any data waiting to be read.
> > +
> > + Polls a serial device to see if there is any data waiting to be read.
> > + If there is data waiting to be read from the serial device, then TRUE is returned.
> > + If there is no data waiting to be read from the serial device, then FALSE is returned.
> > +
> > + @retval TRUE Data is waiting to be read from the serial device.
> > + @retval FALSE There is no data waiting to be read from the serial device.
> > +
> > +**/
> > +BOOLEAN
> > +EFIAPI
> > +SerialPortPoll (
> > + VOID
> > + )
> > +{
> > + return FALSE;
> > +}
> > +
> > +/**
> > + Sets the control bits on a serial device.
> > +
> > + @param Control Sets the bits of Control that are settable.
> > +
> > + @retval RETURN_SUCCESS The new control bits were set on the serial device.
> > + @retval RETURN_UNSUPPORTED The serial device does not support this operation.
> > + @retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
> > +
> > +**/
> > +RETURN_STATUS
> > +EFIAPI
> > +SerialPortSetControl (
> > + IN UINT32 Control
> > + )
> > +{
> > + return RETURN_SUCCESS;
> > +}
> > +
> > +/**
> > + Retrieve the status of the control bits on a serial device.
> > +
> > + @param Control A pointer to return the current control signals from the serial device.
> > +
> > + @retval RETURN_SUCCESS The control bits were read from the serial device.
> > + @retval RETURN_UNSUPPORTED The serial device does not support this operation.
> > + @retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
> > +
> > +**/
> > +RETURN_STATUS
> > +EFIAPI
> > +SerialPortGetControl (
> > + OUT UINT32 *Control
> > + )
> > +{
> > + *Control = 0;
> > + return RETURN_SUCCESS;
> > +}
> > +
> > +/**
> > + Sets the baud rate, receive FIFO depth, transmit/receice time out,
> > +parity,
> > + data bits, and stop bits on a serial device.
> > +
> > + @param BaudRate The requested baud rate. A BaudRate value of 0 will use the
> > + device's default interface speed.
> > + On output, the value actually set.
> > + @param ReveiveFifoDepth The requested depth of the FIFO on the receive side of the
> > + serial interface. A ReceiveFifoDepth value of 0 will use
> > + the device's default FIFO depth.
> > + On output, the value actually set.
> > + @param Timeout The requested time out for a single character in microseconds.
> > + This timeout applies to both the transmit and receive side of the
> > + interface. A Timeout value of 0 will use the device's default time
> > + out value.
> > + On output, the value actually set.
> > + @param Parity The type of parity to use on this serial device. A Parity value of
> > + DefaultParity will use the device's default parity value.
> > + On output, the value actually set.
> > + @param DataBits The number of data bits to use on the serial device. A DataBits
> > + vaule of 0 will use the device's default data bit setting.
> > + On output, the value actually set.
> > + @param StopBits The number of stop bits to use on this serial device. A StopBits
> > + value of DefaultStopBits will use the device's default number of
> > + stop bits.
> > + On output, the value actually set.
> > +
> > + @retval RETURN_SUCCESS The new attributes were set on the serial device.
> > + @retval RETURN_UNSUPPORTED The serial device does not support this operation.
> > + @retval RETURN_INVALID_PARAMETER One or more of the attributes has an unsupported value.
> > + @retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
> > +
> > +**/
> > +RETURN_STATUS
> > +EFIAPI
> > +SerialPortSetAttributes (
> > + IN OUT UINT64 *BaudRate,
> > + IN OUT UINT32 *ReceiveFifoDepth,
> > + IN OUT UINT32 *Timeout,
> > + IN OUT EFI_PARITY_TYPE *Parity,
> > + IN OUT UINT8 *DataBits,
> > + IN OUT EFI_STOP_BITS_TYPE *StopBits
> > + )
> > +{
> > + return RETURN_SUCCESS;
> > +}
> > diff --git
> > a/MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerialPort
> > LibSbi.uni
> > b/MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerialPort
> > LibSbi.uni
> > new file mode 100644
> > index 000000000000..7b22caa5a090
> > --- /dev/null
> > +++ b/MdePkg/Library/PrePiDxeRiscVSerialPortLibSbi/PrePiDxeRiscVSerial
> > +++ Po
> > +++ rtLibSbi.uni
> > @@ -0,0 +1,16 @@
> > +// /** @file
> > +// Serial Port Library backed by SBI console.
> > +//
> > +// Serial Port Library backed by SBI console.
> > +//
> > +// Copyright (c) 2023, Intel Corporation. All rights reserved.<BR> //
> > +// SPDX-License-Identifier: BSD-2-Clause-Patent // // **/
> > +
> > +
> > +#string STR_MODULE_ABSTRACT #language en-US "Serial Port Library backed by SBI console"
> > +
> > +#string STR_MODULE_DESCRIPTION #language en-US "Serial Port Library backed by SBI console."
> > +
> > diff --git
> > a/MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPortLibS
> > bi.uni
> > b/MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPortLibS
> > bi.uni
> > new file mode 100644
> > index 000000000000..7b22caa5a090
> > --- /dev/null
> > +++ b/MdePkg/Library/SecPeiRiscVSerialPortLibSbi/SecPeiRiscVSerialPort
> > +++ LibSbi.uni
> > @@ -0,0 +1,16 @@
> > +// /** @file
> > +// Serial Port Library backed by SBI console.
> > +//
> > +// Serial Port Library backed by SBI console.
> > +//
> > +// Copyright (c) 2023, Intel Corporation. All rights reserved.<BR> //
> > +// SPDX-License-Identifier: BSD-2-Clause-Patent // // **/
> > +
> > +
> > +#string STR_MODULE_ABSTRACT #language en-US "Serial Port Library backed by SBI console"
> > +
> > +#string STR_MODULE_DESCRIPTION #language en-US "Serial Port Library backed by SBI console."
> > +
> > --
> > 2.25.1
next prev parent reply other threads:[~2023-03-27 16:32 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-03-10 17:04 [PATCH v5 0/3] RISC-V SBI-backed SerialLib Andrei Warkentin
2023-03-10 17:04 ` [PATCH v5 1/3] MdePkg: BaseRiscVSbiLib: make more useful to consumers Andrei Warkentin
2023-03-10 17:04 ` [PATCH v5 2/3] MdePkg: add SBI-based SerialPortLib for RISC-V Andrei Warkentin
2023-03-17 4:53 ` Andrei Warkentin
2023-03-17 5:00 ` Michael D Kinney
2023-03-17 5:44 ` Andrei Warkentin
2023-03-27 16:32 ` Michael D Kinney [this message]
2023-03-28 20:00 ` Andrei Warkentin
2023-03-28 20:09 ` Michael D Kinney
2023-03-28 20:20 ` Andrei Warkentin
2023-03-28 21:25 ` Michael D Kinney
2023-03-28 22:00 ` Andrei Warkentin
[not found] ` <174D1E9AD1BD3A96.10271@groups.io>
2023-03-27 16:10 ` [edk2-devel] " Andrei Warkentin
2023-03-10 17:04 ` [PATCH v5 3/3] OvmfPkg: RiscVVirt: Add missing SerialPortInitialize to Sec Andrei Warkentin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-list from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CO1PR11MB4929D85F96C3D7963DD0A3E6D28B9@CO1PR11MB4929.namprd11.prod.outlook.com \
--to=devel@edk2.groups.io \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox