From: "Loh, Tien Hock" <tien.hock.loh@intel.com>
To: "Kinney, Michael D" <michael.d.kinney@intel.com>,
"devel@edk2.groups.io" <devel@edk2.groups.io>
Cc: "thloh85@gmail.com" <thloh85@gmail.com>,
Leif Lindholm <leif@nuviainc.com>,
Ard Biesheuvel <ardb+tianocore@kernel.org>
Subject: Re: [PATCH V5 1/1] EmbeddedPkg: DwMmcHcDxe: Add support for Designware SDMMC driver
Date: Tue, 27 Apr 2021 10:27:56 +0000 [thread overview]
Message-ID: <SJ0PR11MB513626B13059C47EC64D9C89BD419@SJ0PR11MB5136.namprd11.prod.outlook.com> (raw)
In-Reply-To: <SJ0PR11MB51360640336B4C2313A300C5BD419@SJ0PR11MB5136.namprd11.prod.outlook.com>
Hi Mike,
Just to be sure, I'm referring to refactoring to making functions that make calls that uses EFI_PCI_IO_PROTOCOL a generic function that will be implemented as a separate PciIo Sd driver, and Mmio Designware driver, and in the future other Mmio IP Sd driver.
I'll proceed if that is not a concern. If you have other suggestions on the paths I should pursue, please do inform me.
Thanks
> -----Original Message-----
> From: Loh, Tien Hock
> Sent: Tuesday, April 27, 2021 5:08 PM
> To: Kinney, Michael D <michael.d.kinney@intel.com>; devel@edk2.groups.io
> Cc: thloh85@gmail.com; Leif Lindholm <leif@nuviainc.com>; Ard Biesheuvel
> <ardb+tianocore@kernel.org>
> Subject: RE: [PATCH V5 1/1] EmbeddedPkg: DwMmcHcDxe: Add support for
> Designware SDMMC driver
>
> Hi Mike
>
> Yes, the existing Sd driver is very tightly coupled with PCI IO struct, thus the
> reason for a new driver.
> I can attempt to refactor the Pci/SdMmcPciHcDxe and make PCI and Mmio a
> library if that's the best route. I remember I tried briefly to refactor the code
> but it was quite a bit of work.
>
> Let me give it another go, and get back to you.
>
> Thanks.
>
>
> > -----Original Message-----
> > From: Kinney, Michael D <michael.d.kinney@intel.com>
> > Sent: Tuesday, April 27, 2021 1:54 AM
> > To: Loh, Tien Hock <tien.hock.loh@intel.com>; devel@edk2.groups.io;
> > Kinney, Michael D <michael.d.kinney@intel.com>
> > Cc: thloh85@gmail.com; Leif Lindholm <leif@nuviainc.com>; Ard
> Biesheuvel
> > <ardb+tianocore@kernel.org>
> > Subject: RE: [PATCH V5 1/1] EmbeddedPkg: DwMmcHcDxe: Add support
> for
> > Designware SDMMC driver
> >
> > I see the MdeModulePkg has the SdMmcPciHcDxe module and it uses the
> > EDK II SD MMC Override
> > Protocol for host controller specific behaviors. Why was this driver and an
> > implementation
> > of the EDK II SD MMC Override Protocol for the DesignWare MMC HC not
> > used?
> >
> > If there is a good reason that this exiting module and override extensions
> can
> > not be used,
> > then please add that background and analysis to the BZ.
> >
> > I see the existing module is PCI and I think this new one is for a MMIO
> based
> > device
> > that requires different DMA services. Is this correct? I am wondering if
> there
> > is
> > a way to implement t a single UEFI Driver sources that can support a device
> > that is
> > with PCI or MMIO?
> >
> > If a new driver is required, then here is some more specific code review
> > feedback:
> >
> > 1) EmbeddedPkg/Include/Protocol/PlatformSwMmc.h
> >
> > The enum EFI_SD_MMC_SLOT_TYPE can not being with EFI_ unless is part
> > of the UEFI Spec.
> > This file appears to be specific to DW, so perhaps it should be prefixed
> with
> > DW_ instead
> > to match the usage of DW_MMC_HC_SLOT_CAP.
> >
> > The same comment applies to SD_MMC_CARD_TYPE. Should that be
> > DW_SD_MMC_CARD_TYPE?
> >
> >
> > 2) EmbeddedPkg/Drivers/DwMmcHcDxe
> > a) There is a package .dec file in this directory. Packages can never be
> > nested. Any
> > interfaces that need to be exported from the EmbeddedPkg should be
> > declared in
> > EmbeddedPkg.dec and DwMmcDcDxe.dec should be removed.
> > b) DwMmcDcDxe.dec declared a token space GUID, but there are not
> PCDs.
> > I think this GUID
> > can be removed.
> > c) DwMmcDcDxe.inf. Remove reference to DwMmcDcDxe.dec. Also, is
> this
> > UEFI Driver really
> > ARM specific? Why is there a dependency on ArmPkg/ArmPkg.dec?
> Can
> > that be removed?
> > Can the dependency on ArmLib be removed?
> >
> > 3) I see use of #ifdef in the DwMmcHci.h file. This is highly discouraged.
> Why
> > are
> > those there and why not use featured flags PCD instead? If it is related to
> > the
> > PCI vs MMIO register mapping, then perhaps the PCI related content can
> > be removed
> > from this MMIO specific driver?
> >
> > Best regards,
> >
> > Mike
> >
> > > -----Original Message-----
> > > From: Loh, Tien Hock <tien.hock.loh@intel.com>
> > > Sent: Sunday, March 21, 2021 8:25 PM
> > > To: devel@edk2.groups.io
> > > Cc: thloh85@gmail.com; Loh, Tien Hock <tien.hock.loh@intel.com>;
> Kinney,
> > Michael D <michael.d.kinney@intel.com>; Leif
> > > Lindholm <leif@nuviainc.com>; Ard Biesheuvel
> > <ardb+tianocore@kernel.org>
> > > Subject: [PATCH V5 1/1] EmbeddedPkg: DwMmcHcDxe: Add support for
> > Designware SDMMC driver
> > >
> > > From: "Tien Hock, Loh" <tien.hock.loh@intel.com>
> > >
> > > This adds support for Designware SDMMC driver. The SDMMC driver
> > depends on
> > > MdeModulePkg/Bus/Sd/, and produces
> > EFI_SD_MMC_PASS_THRU_PROTOCOL. The
> > > driver uses MMIO to read/write, and uses
> > > gEdkiiNonDiscoverableDeviceProtocolGuid. Platform needs to register
> > device
> > > with gEdkiiNonDiscoverableDeviceProtocolGuid.
> > >
> > > Signed-off-by: Loh Tien Hock <tien.hock.loh@intel.com>
> > > Cc: Leif Lindholm <leif@nuviainc.com>
> > > Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
> > > ---
> > > EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.dec | 40 +
> > > EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.inf | 70 +
> > > EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.h | 817
> > ++++++++++
> > > EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHci.h | 985
> > ++++++++++++
> > > EmbeddedPkg/Include/Protocol/PlatformDwMmc.h | 79 +
> > > EmbeddedPkg/Drivers/DwMmcHcDxe/ComponentName.c | 214 +++
> > > EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.c | 1296
> > ++++++++++++++++
> > > EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHci.c | 1602
> > ++++++++++++++++++++
> > > EmbeddedPkg/Drivers/DwMmcHcDxe/EmmcDevice.c | 1042
> > +++++++++++++
> > > EmbeddedPkg/Drivers/DwMmcHcDxe/SdDevice.c | 1105
> > ++++++++++++++
> > > 10 files changed, 7250 insertions(+)
> > >
> > > diff --git a/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.dec
> > b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.dec
> > > new file mode 100644
> > > index 000000000000..cf85ccb1a030
> > > --- /dev/null
> > > +++ b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.dec
> > > @@ -0,0 +1,40 @@
> > > +#/** @file
> > > +# Framework Module Development Environment Industry Standards
> > > +#
> > > +# This Package provides headers and libraries that conform to EFI/PI
> > Industry standards.
> > > +# Copyright (c) 2007, Intel Corporation. All rights reserved.<BR>
> > > +# Copyright (c) 2012-2014, ARM Ltd. All rights reserved.<BR>
> > > +# Copyright (c) 2018, Linaro. All rights reserved.<BR>
> > > +#
> > > +# This program and the accompanying materials are licensed and made
> > available under
> > > +# the terms and conditions of the BSD License which accompanies this
> > distribution.
> > > +# The full text of the license may be found at
> > > +# http://opensource.org/licenses/bsd-license.php
> > > +#
> > > +# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS
> IS"
> > BASIS,
> > > +# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER
> > EXPRESS OR IMPLIED.
> > > +#
> > > +#**/
> > > +
> > > +[Defines]
> > > + DEC_SPECIFICATION = 0x00010019
> > > + PACKAGE_NAME = DwMmcHcDxePkg
> > > + PACKAGE_GUID = e73097ce-1fe2-41a6-a930-3136bc6d23ef
> > > + PACKAGE_VERSION = 0.1
> > > +
> > > +
> > >
> >
> +#########################################################
> > #######################
> > > +#
> > > +# Include Section - list of Include Paths that are provided by this
> package.
> > > +# Comments are used for Keywords and Module Types.
> > > +#
> > > +# Supported Module Types:
> > > +# BASE SEC PEI_CORE PEIM DXE_CORE DXE_DRIVER
> > DXE_RUNTIME_DRIVER DXE_SMM_DRIVER DXE_SAL_DRIVER UEFI_DRIVER
> > > UEFI_APPLICATION
> > > +#
> > >
> >
> +#########################################################
> > #######################
> > > +
> > > +[Guids.common]
> > > + gDwMmcHcDxeTokenSpaceGuid = { 0x576c132e, 0x7d51, 0x4abb, {
> > 0xbc, 0x60, 0x13, 0x08, 0x04, 0x0e, 0x90, 0x92 }}
> > > +
> > > +[Protocols.common]
> > > + gPlatformDwMmcProtocolGuid = { 0x1d6dfde5, 0x76a7, 0x4404, {
> 0x85,
> > 0x74, 0x7a, 0xdf, 0x1a, 0x8a, 0xa2, 0x0d }}
> > > diff --git a/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.inf
> > b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.inf
> > > new file mode 100644
> > > index 000000000000..4cd0960ef9c3
> > > --- /dev/null
> > > +++ b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.inf
> > > @@ -0,0 +1,70 @@
> > > +## @file
> > > +# DwSdMmcHcDxe driver is used to manage those host controllers
> which
> > comply with
> > > +# Designware SD Host Controller.
> > > +#
> > > +# It will produce EFI_SD_MMC_PASS_THRU_PROTOCOL to allow
> sending
> > SD/MMC/eMMC cmds
> > > +# to specified devices from upper layer.
> > > +#
> > > +# Copyright (c) 2015, Intel Corporation. All rights reserved.<BR>
> > > +# Copyright (C) 2016, Marvell International Ltd. All rights reserved.<BR>
> > > +# Copyright (c) 2018, Linaro Ltd. All rights reserved.<BR>
> > > +#
> > > +# This program and the accompanying materials
> > > +# are licensed and made available under the terms and conditions of
> the
> > BSD License
> > > +# which accompanies this distribution. The full text of the license may
> be
> > found at
> > > +# http://opensource.org/licenses/bsd-license.php
> > > +# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS
> IS"
> > BASIS,
> > > +# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER
> > EXPRESS OR IMPLIED.
> > > +#
> > > +#
> > > +##
> > > +
> > > +[Defines]
> > > + INF_VERSION = 0x00010019
> > > + BASE_NAME = DwMmcHcDxe
> > > + MODULE_UNI_FILE = DwMmcHcDxe.uni
> > > + FILE_GUID = 9be4d260-208c-4efe-a524-0b5d3bf77f9d
> > > + MODULE_TYPE = UEFI_DRIVER
> > > + VERSION_STRING = 1.0
> > > + ENTRY_POINT = InitializeDwMmcHcDxe
> > > +
> > > +[Sources]
> > > + ComponentName.c
> > > + DwMmcHcDxe.c
> > > + DwMmcHcDxe.h
> > > + DwMmcHci.c
> > > + DwMmcHci.h
> > > + EmmcDevice.c
> > > + SdDevice.c
> > > +
> > > +[Packages]
> > > + ArmPkg/ArmPkg.dec
> > > + EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.dec
> > > + EmbeddedPkg/EmbeddedPkg.dec
> > > + MdeModulePkg/MdeModulePkg.dec
> > > + MdePkg/MdePkg.dec
> > > +
> > > +[LibraryClasses]
> > > + ArmLib
> > > + BaseLib
> > > + BaseMemoryLib
> > > + CacheMaintenanceLib
> > > + DebugLib
> > > + DevicePathLib
> > > + DmaLib
> > > + MemoryAllocationLib
> > > + TimerLib
> > > + UefiBootServicesTableLib
> > > + UefiDriverEntryPoint
> > > + UefiLib
> > > + UefiRuntimeServicesTableLib
> > > +
> > > +[Protocols]
> > > + gEdkiiNonDiscoverableDeviceProtocolGuid
> > > + gEfiDevicePathProtocolGuid ## TO_START
> > > + gEfiPciIoProtocolGuid ## TO_START
> > > + gEfiSdMmcPassThruProtocolGuid ## BY_START
> > > + gPlatformDwMmcProtocolGuid
> > > +
> > > +[UserExtensions.TianoCore."ExtraFiles"]
> > > + DwMmcHcDxeExtra.uni
> > > diff --git a/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.h
> > b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.h
> > > new file mode 100644
> > > index 000000000000..b783d9830325
> > > --- /dev/null
> > > +++ b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.h
> > > @@ -0,0 +1,817 @@
> > > +/** @file
> > > +
> > > + Provides some data structure definitions used by the Designware
> > SD/MMC
> > > + host controller driver.
> > > +
> > > + Copyright (c) 2015, Intel Corporation. All rights reserved.<BR>
> > > + Copyright (C) 2018, Linaro Ltd. All rigths reserved.<BR>
> > > +
> > > + This program and the accompanying materials are licensed and made
> > available
> > > + under the terms and conditions of the BSD License which accompanies
> > this
> > > + distribution. The full text of the license may be found at
> > > + http://opensource.org/licenses/bsd-license.php
> > > +
> > > + THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS"
> > BASIS,
> > > + WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER
> > EXPRESS OR IMPLIED.
> > > +
> > > +**/
> > > +
> > > +#ifndef _DW_MMC_HC_DXE_H_
> > > +#define _DW_MMC_HC_DXE_H_
> > > +
> > > +#include <Uefi.h>
> > > +
> > > +#include <Library/UefiLib.h>
> > > +
> > > +#include <Protocol/ComponentName.h>
> > > +#include <Protocol/ComponentName2.h>
> > > +#include <Protocol/DeviceIo.h>
> > > +#include <Protocol/DriverBinding.h>
> > > +#include <Protocol/SdMmcPassThru.h>
> > > +
> > > +#include "DwMmcHci.h"
> > > +
> > > +extern EFI_COMPONENT_NAME_PROTOCOL
> > gDwMmcHcComponentName;
> > > +extern EFI_COMPONENT_NAME2_PROTOCOL
> > gDwMmcHcComponentName2;
> > > +extern EFI_DRIVER_BINDING_PROTOCOL gDwMmcHcDriverBinding;
> > > +
> > > +#define DW_MMC_HC_PRIVATE_SIGNATURE SIGNATURE_32 ('d', 'w',
> 's',
> > 'd')
> > > +
> > > +#define DW_MMC_HC_PRIVATE_FROM_THIS(a) \
> > > + CR(a, DW_MMC_HC_PRIVATE_DATA, PassThru,
> > DW_MMC_HC_PRIVATE_SIGNATURE)
> > > +
> > > +//
> > > +// Generic time out value, 1 microsecond as unit.
> > > +//
> > > +#define DW_MMC_HC_GENERIC_TIMEOUT (1 * 1000 * 1000)
> > > +
> > > +//
> > > +// SD/MMC async transfer timer interval, set by experience.
> > > +// The unit is 100us, takes 1ms as interval.
> > > +//
> > > +#define DW_MMC_HC_ASYNC_TIMER
> > EFI_TIMER_PERIOD_MILLISECONDS(1)
> > > +//
> > > +// SD/MMC removable device enumeration timer interval, set by
> > experience.
> > > +// The unit is 100us, takes 100ms as interval.
> > > +//
> > > +#define DW_MMC_HC_ENUM_TIMER
> > EFI_TIMER_PERIOD_MILLISECONDS(100)
> > > +
> > > +typedef struct {
> > > + BOOLEAN Enable;
> > > + EFI_SD_MMC_SLOT_TYPE SlotType;
> > > + BOOLEAN MediaPresent;
> > > + BOOLEAN Initialized;
> > > + SD_MMC_CARD_TYPE CardType;
> > > +} DW_MMC_HC_SLOT;
> > > +
> > > +typedef struct {
> > > + UINTN Signature;
> > > +
> > > + EFI_HANDLE ControllerHandle;
> > > +
> > > + // Mmio base address
> > > + UINTN DevBase;
> > > +
> > > + EFI_SD_MMC_PASS_THRU_PROTOCOL PassThru;
> > > +
> > > + PLATFORM_DW_MMC_PROTOCOL *PlatformDwMmc;
> > > + //
> > > + // The field is used to record the previous slot in GetNextSlot().
> > > + //
> > > + UINT8 PreviousSlot;
> > > + //
> > > + // For Non-blocking operation.
> > > + //
> > > + EFI_EVENT TimerEvent;
> > > + //
> > > + // For Sd removable device enumeration.
> > > + //
> > > + EFI_EVENT ConnectEvent;
> > > + LIST_ENTRY Queue;
> > > +
> > > + DW_MMC_HC_SLOT Slot[DW_MMC_HC_MAX_SLOT];
> > > + DW_MMC_HC_SLOT_CAP
> > Capability[DW_MMC_HC_MAX_SLOT];
> > > + UINT64 MaxCurrent[DW_MMC_HC_MAX_SLOT];
> > > +
> > > + UINT32 ControllerVersion;
> > > +} DW_MMC_HC_PRIVATE_DATA;
> > > +
> > > +#define DW_MMC_HC_TRB_SIG SIGNATURE_32 ('D', 'T', 'R', 'B')
> > > +
> > > +//
> > > +// TRB (Transfer Request Block) contains information for the cmd
> request.
> > > +//
> > > +typedef struct {
> > > + UINT32 Signature;
> > > + LIST_ENTRY TrbList;
> > > +
> > > + UINT8 Slot;
> > > + UINT16 BlockSize;
> > > +
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet;
> > > + VOID *Data;
> > > + UINT32 DataLen;
> > > + BOOLEAN Read;
> > > + EFI_PHYSICAL_ADDRESS DataPhy;
> > > + VOID *DataMap;
> > > + DW_MMC_HC_TRANSFER_MODE Mode;
> > > +
> > > + EFI_EVENT Event;
> > > + BOOLEAN Started;
> > > + UINT64 Timeout;
> > > +
> > > + DW_MMC_HC_DMA_DESC_LINE *DmaDesc;
> > > + EFI_PHYSICAL_ADDRESS DmaDescPhy;
> > > + UINT32 DmaDescPages;
> > > + VOID *DmaMap;
> > > +
> > > + BOOLEAN UseFifo;
> > > + BOOLEAN UseBE; // Big-endian
> > > +
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > +} DW_MMC_HC_TRB;
> > > +
> > > +#define DW_MMC_HC_TRB_FROM_THIS(a) \
> > > + CR(a, DW_MMC_HC_TRB, TrbList, DW_MMC_HC_TRB_SIG)
> > > +
> > > +//
> > > +// Task for Non-blocking mode.
> > > +//
> > > +typedef struct {
> > > + UINT32 Signature;
> > > + LIST_ENTRY Link;
> > > +
> > > + UINT8 Slot;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet;
> > > + BOOLEAN IsStart;
> > > + EFI_EVENT Event;
> > > + UINT64 RetryTimes;
> > > + BOOLEAN InfiniteWait;
> > > + VOID *Map;
> > > + VOID *MapAddress;
> > > +} DW_MMC_HC_QUEUE;
> > > +
> > > +//
> > > +// Prototypes
> > > +//
> > > +/**
> > > + Execute card identification procedure.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > +
> > > + @retval EFI_SUCCESS The card is identified correctly.
> > > + @retval Others The card can't be identified.
> > > +
> > > +**/
> > > +typedef
> > > +EFI_STATUS
> > > +(*DWMMC_CARD_TYPE_DETECT_ROUTINE) (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private
> > > + );
> > > +
> > > +/**
> > > + Sends SD command to an SD card that is attached to the SD controller.
> > > +
> > > + The PassThru() function sends the SD command specified by Packet to
> > the SD
> > > + card specified by Slot.
> > > +
> > > + If Packet is successfully sent to the SD card, then EFI_SUCCESS is
> > returned.
> > > +
> > > + If a device error occurs while sending the Packet, then
> > EFI_DEVICE_ERROR is
> > > + returned.
> > > +
> > > + If Slot is not in a valid range for the SD controller, then
> > > + EFI_INVALID_PARAMETER is returned.
> > > +
> > > + If Packet defines a data command but both InDataBuffer and
> > OutDataBuffer are
> > > + NULL, EFI_INVALID_PARAMETER is returned.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > > + command to.
> > > + @param[in,out] Packet A pointer to the SD command data
> structure.
> > > + @param[in] Event If Event is NULL, blocking I/O is performed. If
> > > + Event is not NULL, then nonblocking I/O is
> > > + performed, and Event will be signaled when the
> > > + Packet completes.
> > > +
> > > + @retval EFI_SUCCESS The SD Command Packet was sent by the
> > host.
> > > + @retval EFI_DEVICE_ERROR A device error occurred while
> attempting
> > to send
> > > + the SD command Packet.
> > > + @retval EFI_INVALID_PARAMETER Packet, Slot, or the contents of the
> > Packet is
> > > + invalid.
> > > + @retval EFI_INVALID_PARAMETER Packet defines a data command but
> > both
> > > + InDataBuffer and OutDataBuffer are NULL.
> > > + @retval EFI_NO_MEDIA SD Device not present in the Slot.
> > > + @retval EFI_UNSUPPORTED The command described by the SD
> > Command Packet
> > > + is not supported by the host controller.
> > > + @retval EFI_BAD_BUFFER_SIZE The InTransferLength or
> > OutTransferLength
> > > + exceeds the limit supported by SD card ( i.e. if
> > > + the number of bytes exceed the Last LBA).
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcPassThruPassThru (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *This,
> > > + IN UINT8 Slot,
> > > + IN OUT EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet,
> > > + IN EFI_EVENT Event OPTIONAL
> > > + );
> > > +
> > > +/**
> > > + Used to retrieve next slot numbers supported by the SD controller. The
> > > + function returns information about all available slots (populated or
> > > + not-populated).
> > > +
> > > + The GetNextSlot() function retrieves the next slot number on an SD
> > controller.
> > > + If on input Slot is 0xFF, then the slot number of the first slot on the SD
> > > + controller is returned.
> > > +
> > > + If Slot is a slot number that was returned on a previous call to
> > > + GetNextSlot(), then the slot number of the next slot on the SD
> controller
> > is
> > > + returned.
> > > +
> > > + If Slot is not 0xFF and Slot was not returned on a previous call to
> > > + GetNextSlot(), EFI_INVALID_PARAMETER is returned.
> > > +
> > > + If Slot is the slot number of the last slot on the SD controller, then
> > > + EFI_NOT_FOUND is returned.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_SD_MMMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in,out] Slot On input, a pointer to a slot number on the
> SD
> > > + controller.
> > > + On output, a pointer to the next slot number on
> > > + the SD controller.
> > > + An input value of 0xFF retrieves the first slot
> > > + number on the SD controller.
> > > +
> > > + @retval EFI_SUCCESS The next slot number on the SD controller
> > was
> > > + returned in Slot.
> > > + @retval EFI_NOT_FOUND There are no more slots on this SD
> > controller.
> > > + @retval EFI_INVALID_PARAMETER Slot is not 0xFF and Slot was not
> > returned on a
> > > + previous call to GetNextSlot().
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcPassThruGetNextSlot (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *This,
> > > + IN OUT UINT8 *Slot
> > > + );
> > > +
> > > +/**
> > > + Used to allocate and build a device path node for an SD card on the SD
> > > + controller.
> > > +
> > > + The BuildDevicePath() function allocates and builds a single device
> node
> > > + for the SD
> > > + card specified by Slot.
> > > +
> > > + If the SD card specified by Slot is not present on the SD controller, then
> > > + EFI_NOT_FOUND is returned.
> > > +
> > > + If DevicePath is NULL, then EFI_INVALID_PARAMETER is returned.
> > > +
> > > + If there are not enough resources to allocate the device path node,
> then
> > > + EFI_OUT_OF_RESOURCES is returned.
> > > +
> > > + Otherwise, DevicePath is allocated with the boot service
> AllocatePool(),
> > the
> > > + contents of DevicePath are initialized to describe the SD card specified
> by
> > > + Slot, and EFI_SUCCESS is returned.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_SD_MMMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Slot Specifies the slot number of the SD card for
> > > + which a device path node is to be allocated and
> > > + built.
> > > + @param[in,out] DevicePath A pointer to a single device path node
> that
> > > + describes the SD card specified by Slot. This
> > > + function is responsible for allocating the
> > > + buffer DevicePath with the boot service
> > > + AllocatePool(). It is the caller's responsibi-
> > > + lity to free DevicePath when the caller is
> > > + finished with DevicePath.
> > > +
> > > + @retval EFI_SUCCESS The device path node that describes the SD
> > card
> > > + specified by Slot was allocated and returned in
> > > + DevicePath.
> > > + @retval EFI_NOT_FOUND The SD card specified by Slot does not
> > exist on
> > > + the SD controller.
> > > + @retval EFI_INVALID_PARAMETER DevicePath is NULL.
> > > + @retval EFI_OUT_OF_RESOURCES There are not enough resources to
> > allocate
> > > + DevicePath.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcPassThruBuildDevicePath (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *This,
> > > + IN UINT8 Slot,
> > > + IN OUT EFI_DEVICE_PATH_PROTOCOL **DevicePath
> > > + );
> > > +
> > > +/**
> > > + This function retrieves an SD card slot number based on the input
> device
> > path.
> > > +
> > > + The GetSlotNumber() function retrieves slot number for the SD card
> > specified
> > > + by the DevicePath node. If DevicePath is NULL,
> > EFI_INVALID_PARAMETER is
> > > + returned.
> > > +
> > > + If DevicePath is not a device path node type that the SD Pass Thru
> driver
> > > + supports, EFI_UNSUPPORTED is returned.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] DevicePath A pointer to the device path node that
> > describes
> > > + a SD card on the SD controller.
> > > + @param[out] Slot On return, points to the slot number of an SD
> > > + card on the SD controller.
> > > +
> > > + @retval EFI_SUCCESS SD card slot number is returned in Slot.
> > > + @retval EFI_INVALID_PARAMETER Slot or DevicePath is NULL.
> > > + @retval EFI_UNSUPPORTED DevicePath is not a device path node
> > type that
> > > + the SD Pass Thru driver supports.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcPassThruGetSlotNumber (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *This,
> > > + IN EFI_DEVICE_PATH_PROTOCOL *DevicePath,
> > > + OUT UINT8 *Slot
> > > + );
> > > +
> > > +/**
> > > + Resets an SD card that is connected to the SD controller.
> > > +
> > > + The ResetDevice() function resets the SD card specified by Slot.
> > > +
> > > + If this SD controller does not support a device reset operation,
> > > + EFI_UNSUPPORTED is returned.
> > > +
> > > + If Slot is not in a valid slot number for this SD controller,
> > > + EFI_INVALID_PARAMETER is returned.
> > > +
> > > + If the device reset operation is completed, EFI_SUCCESS is returned.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Slot Specifies the slot number of the SD card to be
> > > + reset.
> > > +
> > > + @retval EFI_SUCCESS The SD card specified by Slot was reset.
> > > + @retval EFI_UNSUPPORTED The SD controller does not support a
> > device
> > > + reset operation.
> > > + @retval EFI_INVALID_PARAMETER Slot number is invalid.
> > > + @retval EFI_NO_MEDIA SD Device not present in the Slot.
> > > + @retval EFI_DEVICE_ERROR The reset command failed due to a
> device
> > error
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcPassThruResetDevice (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *This,
> > > + IN UINT8 Slot
> > > + );
> > > +
> > > +//
> > > +// Driver model protocol interfaces
> > > +//
> > > +/**
> > > + Tests to see if this driver supports a given controller. If a child device is
> > > + provided, it further tests to see if this driver supports creating a handle
> > > + for the specified child device.
> > > +
> > > + This function checks to see if the driver specified by This supports the
> > > + device specified by ControllerHandle. Drivers will typically use the
> device
> > > + path attached to ControllerHandle and/or the services from the bus I/O
> > > + abstraction attached to ControllerHandle to determine if the driver
> > supports
> > > + ControllerHandle. This function may be called many times during
> > platform
> > > + initialization. In order to reduce boot times, the tests performed by this
> > > + function must be very small, and take as little time as possible to
> > execute.
> > > + This function must not change the state of any hardware devices, and
> > this
> > > + function must be aware that the device specified by ControllerHandle
> > may
> > > + already be managed by the same driver or a different driver. This
> > function
> > > + must match its calls to AllocatePages() with FreePages(), AllocatePool()
> > with
> > > + FreePool(), and OpenProtocol() with CloseProtocol().
> > > + Since ControllerHandle may have been previously started by the same
> > driver, if
> > > + a protocol is already in the opened state, then it must not be closed
> with
> > > + CloseProtocol(). This is required to guarantee the state of
> > ControllerHandle
> > > + is not modified by this function.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_DRIVER_BINDING_PROTOCOL
> > > + instance.
> > > + @param[in] ControllerHandle The handle of the controller to test.
> This
> > > + handle must support a protocol interface that
> > > + supplies an I/O abstraction to the driver.
> > > + @param[in] RemainingDevicePath A pointer to the remaining portion
> of
> > a
> > > + device path. This parameter is ignored by
> > > + device drivers, and is optional for bus
> > > + drivers. For bus drivers, if this parameter
> > > + is not NULL, then the bus driver must deter-
> > > + mine if the bus controller specified by
> > > + ControllerHandle and the child controller
> > > + specified by RemainingDevicePath are both
> > > + supported by this bus driver.
> > > +
> > > + @retval EFI_SUCCESS The device specified by ControllerHandle
> > and
> > > + RemainingDevicePath is supported by the
> > > + driver specified by This.
> > > + @retval EFI_ALREADY_STARTED The device specified by
> > ControllerHandle and
> > > + RemainingDevicePath is already being managed
> > > + by the driver specified by This.
> > > + @retval EFI_ACCESS_DENIED The device specified by
> > ControllerHandle and
> > > + RemainingDevicePath is already being managed
> > > + by a different driver or an application that
> > > + requires exclusive access.
> > > + Currently not implemented.
> > > + @retval EFI_UNSUPPORTED The device specified by
> > ControllerHandle and
> > > + RemainingDevicePath is not supported by the
> > > + driver specified by This.
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcDriverBindingSupported (
> > > + IN EFI_DRIVER_BINDING_PROTOCOL *This,
> > > + IN EFI_HANDLE Controller,
> > > + IN EFI_DEVICE_PATH_PROTOCOL *RemainingDevicePath
> > > + );
> > > +
> > > +/**
> > > + Starts a device controller or a bus controller.
> > > +
> > > + The Start() function is designed to be invoked from the EFI boot service
> > > + ConnectController().
> > > + As a result, much of the error checking on the parameters to Start() has
> > been
> > > + moved into this common boot service. It is legal to call Start() from
> other
> > > + locations,
> > > + but the following calling restrictions must be followed or the system
> > behavior
> > > + will not be deterministic.
> > > + 1. ControllerHandle must be a valid EFI_HANDLE.
> > > + 2. If RemainingDevicePath is not NULL, then it must be a pointer to a
> > natural-
> > > + ly aligned EFI_DEVICE_PATH_PROTOCOL.
> > > + 3. Prior to calling Start(), the Supported() function for the driver
> specified
> > > + by This must have been called with the same calling parameters, and
> > > + Supported() must have returned EFI_SUCCESS.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_DRIVER_BINDING_PROTOCOL
> > > + instance.
> > > + @param[in] ControllerHandle The handle of the controller to start.
> > This
> > > + handle must support a protocol interface that
> > > + supplies an I/O abstraction to the driver.
> > > + @param[in] RemainingDevicePath A pointer to the remaining portion
> of
> > a
> > > + device path. This parameter is ignored by
> > > + device drivers, and is optional for bus dri-
> > > + vers. For a bus driver, if this parameter is
> > > + NULL, then handles for all the children of
> > > + Controller are created by this driver.
> > > + If this parameter is not NULL and the first
> > > + Device Path Node is not the End of Device
> > > + Path Node, then only the handle for the
> > > + child device specified by the first Device
> > > + Path Node of RemainingDevicePath is created
> > > + by this driver.
> > > + If the first Device Path Node of
> > > + RemainingDevicePath is the End of Device Path
> > > + Node, no child handle is created by this
> > > + driver.
> > > +
> > > + @retval EFI_SUCCESS The device was started.
> > > + @retval EFI_DEVICE_ERROR The device could not be started due to
> a
> > > + device error. Currently not implemented.
> > > + @retval EFI_OUT_OF_RESOURCES The request could not be
> > completed due to a
> > > + lack of resources.
> > > + @retval Others The driver failded to start the device.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcDriverBindingStart (
> > > + IN EFI_DRIVER_BINDING_PROTOCOL *This,
> > > + IN EFI_HANDLE Controller,
> > > + IN EFI_DEVICE_PATH_PROTOCOL *RemainingDevicePath
> > > + );
> > > +
> > > +/**
> > > + Stops a device controller or a bus controller.
> > > +
> > > + The Stop() function is designed to be invoked from the EFI boot service
> > > + DisconnectController().
> > > + As a result, much of the error checking on the parameters to Stop() has
> > been
> > > + moved into this common boot service. It is legal to call Stop() from
> other
> > > + locations, but the following calling restrictions must be followed or the
> > > + system behavior will not be deterministic.
> > > + 1. ControllerHandle must be a valid EFI_HANDLE that was used on a
> > previous
> > > + call to this same driver's Start() function.
> > > + 2. The first NumberOfChildren handles of ChildHandleBuffer must all
> be a
> > valid
> > > + EFI_HANDLE. In addition, all of these handles must have been created
> > in
> > > + this driver's Start() function, and the Start() function must have called
> > > + OpenProtocol() on ControllerHandle with an Attribute of
> > > + EFI_OPEN_PROTOCOL_BY_CHILD_CONTROLLER.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_DRIVER_BINDING_PROTOCOL
> > > + instance.
> > > + @param[in] ControllerHandle A handle to the device being stopped.
> > The handle
> > > + must support a bus specific I/O protocol for the
> > > + driver to use to stop the device.
> > > + @param[in] NumberOfChildren The number of child device handles in
> > > + ChildHandleBuffer.
> > > + @param[in] ChildHandleBuffer An array of child handles to be freed.
> > May be
> > > + NULL if NumberOfChildren is 0.
> > > +
> > > + @retval EFI_SUCCESS The device was stopped.
> > > + @retval EFI_DEVICE_ERROR The device could not be stopped due to
> a
> > device
> > > + error.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcDriverBindingStop (
> > > + IN EFI_DRIVER_BINDING_PROTOCOL *This,
> > > + IN EFI_HANDLE Controller,
> > > + IN UINTN NumberOfChildren,
> > > + IN EFI_HANDLE *ChildHandleBuffer
> > > + );
> > > +
> > > +//
> > > +// EFI Component Name Functions
> > > +//
> > > +/**
> > > + Retrieves a Unicode string that is the user readable name of the driver.
> > > +
> > > + This function retrieves the user readable name of a driver in the form
> of
> > a
> > > + Unicode string. If the driver specified by This has a user readable name
> in
> > > + the language specified by Language, then a pointer to the driver name
> is
> > > + returned in DriverName, and EFI_SUCCESS is returned. If the driver
> > specified
> > > + by This does not support the language specified by Language,
> > > + then EFI_UNSUPPORTED is returned.
> > > +
> > > + @param This[in] A pointer to the
> > EFI_COMPONENT_NAME2_PROTOCOL or
> > > + EFI_COMPONENT_NAME_PROTOCOL instance.
> > > +
> > > + @param Language[in] A pointer to a Null-terminated ASCII string
> > > + array indicating the language. This is the
> > > + language of the driver name that the caller is
> > > + requesting, and it must match one of the
> > > + languages specified in SupportedLanguages. The
> > > + number of languages supported by a driver is up
> > > + to the driver writer. Language is specified
> > > + in RFC 4646 or ISO 639-2 language code format.
> > > +
> > > + @param DriverName[out] A pointer to the Unicode string to return.
> > > + This Unicode string is the name of the
> > > + driver specified by This in the language
> > > + specified by Language.
> > > +
> > > + @retval EFI_SUCCESS The Unicode string for the Driver specified
> by
> > > + This and the language specified by Language was
> > > + returned in DriverName.
> > > +
> > > + @retval EFI_INVALID_PARAMETER Language is NULL.
> > > +
> > > + @retval EFI_INVALID_PARAMETER DriverName is NULL.
> > > +
> > > + @retval EFI_UNSUPPORTED The driver specified by This does not
> > support
> > > + the language specified by Language.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcComponentNameGetDriverName (
> > > + IN EFI_COMPONENT_NAME_PROTOCOL *This,
> > > + IN CHAR8 *Language,
> > > + OUT CHAR16 **DriverName
> > > + );
> > > +
> > > +/**
> > > + Retrieves a Unicode string that is the user readable name of the
> > controller
> > > + that is being managed by a driver.
> > > +
> > > + This function retrieves the user readable name of the controller
> specified
> > by
> > > + ControllerHandle and ChildHandle in the form of a Unicode string. If the
> > > + driver specified by This has a user readable name in the language
> > specified by
> > > + Language, then a pointer to the controller name is returned in
> > ControllerName,
> > > + and EFI_SUCCESS is returned. If the driver specified by This is not
> > currently
> > > + managing the controller specified by ControllerHandle and ChildHandle,
> > > + then EFI_UNSUPPORTED is returned. If the driver specified by This
> does
> > not
> > > + support the language specified by Language, then EFI_UNSUPPORTED
> is
> > returned.
> > > +
> > > + @param This[in] A pointer to the
> > EFI_COMPONENT_NAME2_PROTOCOL or
> > > + EFI_COMPONENT_NAME_PROTOCOL instance.
> > > +
> > > + @param ControllerHandle[in] The handle of a controller that the
> driver
> > > + specified by This is managing. This handle
> > > + specifies the controller whose name is to be
> > > + returned.
> > > +
> > > + @param ChildHandle[in] The handle of the child controller to
> retrieve
> > > + the name of. This is an optional parameter that
> > > + may be NULL. It will be NULL for device
> > > + drivers. It will also be NULL for a bus drivers
> > > + that wish to retrieve the name of the bus
> > > + controller. It will not be NULL for a bus
> > > + driver that wishes to retrieve the name of a
> > > + child controller.
> > > +
> > > + @param Language[in] A pointer to a Null-terminated ASCII string
> > > + array indicating the language. This is the
> > > + language of the driver name that the caller is
> > > + requesting, and it must match one of the
> > > + languages specified in SupportedLanguages. The
> > > + number of languages supported by a driver is up
> > > + to the driver writer. Language is specified in
> > > + RFC 4646 or ISO 639-2 language code format.
> > > +
> > > + @param ControllerName[out] A pointer to the Unicode string to
> > return.
> > > + This Unicode string is the name of the
> > > + controller specified by ControllerHandle and
> > > + ChildHandle in the language specified by
> > > + Language from the point of view of the driver
> > > + specified by This.
> > > +
> > > + @retval EFI_SUCCESS The Unicode string for the user readable
> > name in
> > > + the language specified by Language for the
> > > + driver specified by This was returned in
> > > + DriverName.
> > > +
> > > + @retval EFI_INVALID_PARAMETER ControllerHandle is not a valid
> > EFI_HANDLE.
> > > +
> > > + @retval EFI_INVALID_PARAMETER ChildHandle is not NULL and it is not
> a
> > valid
> > > + EFI_HANDLE.
> > > +
> > > + @retval EFI_INVALID_PARAMETER Language is NULL.
> > > +
> > > + @retval EFI_INVALID_PARAMETER ControllerName is NULL.
> > > +
> > > + @retval EFI_UNSUPPORTED The driver specified by This is not
> > currently
> > > + managing the controller specified by
> > > + ControllerHandle and ChildHandle.
> > > +
> > > + @retval EFI_UNSUPPORTED The driver specified by This does not
> > support
> > > + the language specified by Language.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcComponentNameGetControllerName (
> > > + IN EFI_COMPONENT_NAME_PROTOCOL *This,
> > > + IN EFI_HANDLE ControllerHandle,
> > > + IN EFI_HANDLE ChildHandle, OPTIONAL
> > > + IN CHAR8 *Language,
> > > + OUT CHAR16 **ControllerName
> > > + );
> > > +
> > > +/**
> > > + Create a new TRB for the SD/MMC cmd request.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command
> > > + to.
> > > + @param[in] Packet A pointer to the SD command data structure.
> > > + @param[in] Event If Event is NULL, blocking I/O is performed.
> > > + If Event is not NULL, then nonblocking I/O is
> > > + performed, and Event will be signaled when the
> > > + Packet completes.
> > > +
> > > + @return Created Trb or NULL.
> > > +
> > > +**/
> > > +DW_MMC_HC_TRB *
> > > +DwMmcCreateTrb (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN UINT8 Slot,
> > > + IN EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet,
> > > + IN EFI_EVENT Event
> > > + );
> > > +
> > > +/**
> > > + Free the resource used by the TRB.
> > > +
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > +**/
> > > +VOID
> > > +DwMmcFreeTrb (
> > > + IN DW_MMC_HC_TRB *Trb
> > > + );
> > > +
> > > +/**
> > > + Check if the env is ready for execute specified TRB.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > + @retval EFI_SUCCESS The env is ready for TRB execution.
> > > + @retval EFI_NOT_READY The env is not ready for TRB execution.
> > > + @retval Others Some erros happen.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcCheckTrbEnv (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + );
> > > +
> > > +/**
> > > + Wait for the env to be ready for execute specified TRB.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > + @retval EFI_SUCCESS The env is ready for TRB execution.
> > > + @retval EFI_TIMEOUT The env is not ready for TRB execution in
> time.
> > > + @retval Others Some erros happen.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcWaitTrbEnv (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + );
> > > +
> > > +/**
> > > + Execute the specified TRB.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > + @retval EFI_SUCCESS The TRB is sent to host controller successfully.
> > > + @retval Others Some erros happen when sending this request to
> > the
> > > + host controller.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcExecTrb (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + );
> > > +
> > > +/**
> > > + Check the TRB execution result.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > + @retval EFI_SUCCESS The TRB is executed successfully.
> > > + @retval EFI_NOT_READY The TRB is not completed for execution.
> > > + @retval Others Some erros happen when executing this request.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcCheckTrbResult (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + );
> > > +
> > > +/**
> > > + Wait for the TRB execution result.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > + @retval EFI_SUCCESS The TRB is executed successfully.
> > > + @retval Others Some erros happen when executing this request.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcWaitTrbResult (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + );
> > > +
> > > +/**
> > > + Execute EMMC device identification procedure.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > +
> > > + @retval EFI_SUCCESS There is a EMMC card.
> > > + @retval Others There is not a EMMC card.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcIdentification (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private
> > > + );
> > > +
> > > +/**
> > > + Execute EMMC device identification procedure.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > +
> > > + @retval EFI_SUCCESS There is a EMMC card.
> > > + @retval Others There is not a EMMC card.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardIdentification (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private
> > > + );
> > > +
> > > +#endif /* _DW_MMC_HC_DXE_H_ */
> > > diff --git a/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHci.h
> > b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHci.h
> > > new file mode 100644
> > > index 000000000000..12ef58a37368
> > > --- /dev/null
> > > +++ b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHci.h
> > > @@ -0,0 +1,985 @@
> > > +/** @file
> > > +
> > > + Provides some data structure definitions used by the SD/MMC host
> > controller
> > > + driver.
> > > +
> > > + Copyright (c) 2015, Intel Corporation. All rights reserved.<BR>
> > > + Copyright (c) 2018, Linaro Ltd. All rights reserved.<BR>
> > > +
> > > + This program and the accompanying materials are licensed and made
> > available
> > > + under the terms and conditions of the BSD License which accompanies
> > this
> > > + distribution. The full text of the license may be found at
> > > + http://opensource.org/licenses/bsd-license.php
> > > +
> > > + THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS"
> > BASIS,
> > > + WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER
> > EXPRESS OR IMPLIED.
> > > +
> > > +**/
> > > +
> > > +#ifndef _DW_MMC_HCI_H_
> > > +#define _DW_MMC_HCI_H_
> > > +
> > > +#include <Library/CacheMaintenanceLib.h>
> > > +#include <Library/TimerLib.h>
> > > +
> > > +#include <Protocol/PlatformDwMmc.h>
> > > +
> > > +//
> > > +// SD Host Controller SlotInfo Register Offset
> > > +//
> > > +#define DW_MMC_HC_SLOT_OFFSET 0x40
> > > +
> > > +#define DW_MMC_HC_MAX_SLOT 1
> > > +
> > > +//
> > > +// SD Host Controller MMIO Register Offset
> > > +//
> > > +#define DW_MMC_CTRL 0x000
> > > +#define DW_MMC_PWREN 0x004
> > > +#define DW_MMC_CLKDIV 0x008
> > > +#define DW_MMC_CLKSRC 0x00c
> > > +#define DW_MMC_CLKENA 0x010
> > > +#define DW_MMC_TMOUT 0x014
> > > +#define DW_MMC_CTYPE 0x018
> > > +#define DW_MMC_BLKSIZ 0x01c
> > > +#define DW_MMC_BYTCNT 0x020
> > > +#define DW_MMC_INTMASK 0x024
> > > +#define DW_MMC_CMDARG 0x028
> > > +#define DW_MMC_CMD 0x02c
> > > +#define DW_MMC_RESP0 0x030
> > > +#define DW_MMC_RESP1 0x034
> > > +#define DW_MMC_RESP2 0x038
> > > +#define DW_MMC_RESP3 0x03c
> > > +#define DW_MMC_RINTSTS 0x044
> > > +#define DW_MMC_STATUS 0x048
> > > +#define DW_MMC_FIFOTH 0x04c
> > > +#define DW_MMC_GPIO 0x058
> > > +#define DW_MMC_DEBNCE 0x064
> > > +#define DW_MMC_USRID 0x068
> > > +#define DW_MMC_VERID 0x06c
> > > +#define DW_MMC_HCON 0x070
> > > +#define DW_MMC_UHSREG 0x074
> > > +#define DW_MMC_BMOD 0x080
> > > +#define DW_MMC_DBADDR 0x088
> > > +#define DW_MMC_IDSTS 0x08c
> > > +#define DW_MMC_IDINTEN 0x090
> > > +#define DW_MMC_DSCADDR 0x094
> > > +#define DW_MMC_BUFADDR 0x098
> > > +#define DW_MMC_CARDTHRCTL 0x100
> > > +#define DW_MMC_UHSREG_EXT 0x108
> > > +#define DW_MMC_ENABLE_SHIFT 0x110
> > > +#define DW_MMC_FIFO_START 0x200
> > > +
> > > +#define GET_IDSTS_DMAC_FSM(x) (((x) >> 13) & 0xf)
> > > +#define IDSTS_FSM_DMA_IDLE 0
> > > +#define IDSTS_FSM_DMA_SUSPEND 1
> > > +#define IDSTS_FSM_DESC_RD 2
> > > +#define IDSTS_FSM_DESC_CHK 3
> > > +#define IDSTS_FSM_DMA_RD_REQ_WAIT 4
> > > +#define IDSTS_FSM_DMA_WR_REQ_WAIT 5
> > > +#define IDSTS_FSM_DMA_RD 6
> > > +#define IDSTS_FSM_DMA_WR 7
> > > +#define IDSTS_FSM_DESC_CLOSE 8
> > > +#define IDSTS_FSM_MASK 0xf
> > > +
> > > +#define CMD_UPDATE_CLK 0x80202000
> > > +#define CMD_START_BIT (1 << 31)
> > > +
> > > +#define MMC_8BIT_MODE (1 << 16)
> > > +#define MMC_4BIT_MODE (1 << 0)
> > > +#define MMC_1BIT_MODE 0
> > > +
> > > +#define DW_MMC_BLOCK_SIZE 512
> > > +
> > > +#define CMD_INDEX_MASK 0x3F
> > > +#define BIT_CMD_RESPONSE_EXPECT (1 << 6)
> > > +#define BIT_CMD_LONG_RESPONSE (1 << 7)
> > > +#define BIT_CMD_CHECK_RESPONSE_CRC (1 << 8)
> > > +#define BIT_CMD_DATA_EXPECTED (1 << 9)
> > > +#define BIT_CMD_READ (0 << 10)
> > > +#define BIT_CMD_WRITE (1 << 10)
> > > +#define BIT_CMD_BLOCK_TRANSFER (0 << 11)
> > > +#define BIT_CMD_STREAM_TRANSFER (1 << 11)
> > > +#define BIT_CMD_SEND_AUTO_STOP (1 << 12)
> > > +#define BIT_CMD_WAIT_PRVDATA_COMPLETE (1 << 13)
> > > +#define BIT_CMD_STOP_ABORT_CMD (1 << 14)
> > > +#define BIT_CMD_SEND_INIT (1 << 15)
> > > +#define BIT_CMD_UPDATE_CLOCK_ONLY (1 << 21)
> > > +#define BIT_CMD_READ_CEATA_DEVICE (1 << 22)
> > > +#define BIT_CMD_CCS_EXPECTED (1 << 23)
> > > +#define BIT_CMD_ENABLE_BOOT (1 << 24)
> > > +#define BIT_CMD_EXPECT_BOOT_ACK (1 << 25)
> > > +#define BIT_CMD_DISABLE_BOOT (1 << 26)
> > > +#define BIT_CMD_MANDATORY_BOOT (0 << 27)
> > > +#define BIT_CMD_ALTERNATE_BOOT (1 << 27)
> > > +#define BIT_CMD_VOLT_SWITCH (1 << 28)
> > > +#define BIT_CMD_USE_HOLD_REG (1 << 29)
> > > +#define BIT_CMD_START (1 << 31)
> > > +
> > > +#define CMD_INDEX(x) ((x) & CMD_INDEX_MASK)
> > > +
> > > +#define DW_MMC_INT_EBE (1 << 15) /* End-bit Err */
> > > +#define DW_MMC_INT_SBE (1 << 13) /* Start-bit Err */
> > > +#define DW_MMC_INT_HLE (1 << 12) /* Hardware-lock
> > Err */
> > > +#define DW_MMC_INT_FRUN (1 << 11) /* FIFO UN/OV
> > RUN */
> > > +#define DW_MMC_INT_DRT (1 << 9) /* Data timeout */
> > > +#define DW_MMC_INT_RTO (1 << 8) /* Response
> > timeout */
> > > +#define DW_MMC_INT_DCRC (1 << 7) /* Data CRC err */
> > > +#define DW_MMC_INT_RCRC (1 << 6) /* Response CRC
> > err */
> > > +#define DW_MMC_INT_RXDR (1 << 5) /* Receive FIFO
> > data request */
> > > +#define DW_MMC_INT_TXDR (1 << 4) /* Transmit FIFO
> > data request */
> > > +#define DW_MMC_INT_DTO (1 << 3) /* Data trans over
> > */
> > > +#define DW_MMC_INT_CMD_DONE (1 << 2) /* Command
> > done */
> > > +#define DW_MMC_INT_RE (1 << 1) /* Response error
> */
> > > +
> > > +#define DW_MMC_IDMAC_DES0_DIC (1 << 1)
> > > +#define DW_MMC_IDMAC_DES0_LD (1 << 2)
> > > +#define DW_MMC_IDMAC_DES0_FS (1 << 3)
> > > +#define DW_MMC_IDMAC_DES0_CH (1 << 4)
> > > +#define DW_MMC_IDMAC_DES0_ER (1 << 5)
> > > +#define DW_MMC_IDMAC_DES0_CES (1 << 30)
> > > +#define DW_MMC_IDMAC_DES0_OWN (1 << 31)
> > > +#define DW_MMC_IDMAC_DES1_BS1(x) ((x) & 0x1fff)
> > > +#define DW_MMC_IDMAC_DES2_BS2(x) (((x) & 0x1fff) << 13)
> > > +#define DW_MMC_IDMAC_SWRESET (1 << 0)
> > > +#define DW_MMC_IDMAC_FB (1 << 1)
> > > +#define DW_MMC_IDMAC_ENABLE (1 << 7)
> > > +
> > > +#define DW_MMC_CTRL_RESET (1 << 0)
> > > +#define DW_MMC_CTRL_FIFO_RESET (1 << 1)
> > > +#define DW_MMC_CTRL_DMA_RESET (1 << 2)
> > > +#define DW_MMC_CTRL_INT_EN (1 << 4)
> > > +#define DW_MMC_CTRL_DMA_EN (1 << 5)
> > > +#define DW_MMC_CTRL_IDMAC_EN (1 << 25)
> > > +#define DW_MMC_CTRL_RESET_ALL (DW_MMC_CTRL_RESET
> |
> > DW_MMC_CTRL_FIFO_RESET | DW_MMC_CTRL_DMA_RESET)
> > > +
> > > +#define DW_MMC_STS_DATA_BUSY (1 << 9)
> > > +#define DW_MMC_STS_FIFO_COUNT(x) (((x) & 0x1fff) << 17)
> /*
> > Number of filled locations in FIFO */
> > > +#define GET_STS_FIFO_COUNT(x) (((x) >> 17) & 0x1fff)
> > > +#define DW_MMC_STS_FIFO_FULL(x) (((x) >> 3) & 1)
> > > +
> > > +#define DW_MMC_BMOD_SWR (1 << 0) /* Software
> > Reset */
> > > +#define DW_MMC_BMOD_FB (1 << 1) /* Fix Burst */
> > > +#define DW_MMC_BMOD_DE (1 << 7) /* IDMAC
> Enable
> > */
> > > +
> > > +#define DW_MMC_IDSTS_TI (1 << 0) /* Transmit
> > Interrupt */
> > > +#define DW_MMC_IDSTS_RI (1 << 1) /* Receive
> Interrupt
> > */
> > > +
> > > +#define DW_MMC_FIFO_TWMARK(x) ((x) & 0xfff)
> > > +#define DW_MMC_FIFO_RWMARK(x) (((x) & 0x1ff) << 16)
> > > +#define DW_MMC_DMA_BURST_SIZE(x) (((x) & 0x7) << 28)
> > > +
> > > +#define DW_MMC_CARD_RD_THR(x) (((x) & 0xfff) << 16)
> > > +#define DW_MMC_CARD_RD_THR_EN (1 << 0)
> > > +
> > > +#define UHS_DDR_MODE (1 << 16)
> > > +
> > > +#define GENCLK_DIV 7
> > > +
> > > +#define DW_MMC_GPIO_CLK_DIV(x) (((x) & 0xf) << 8)
> > > +#define DW_MMC_GPIO_USE_SAMPLE_DLY(x) (((x) & 1) << 13)
> > > +#define DW_MMC_GPIO_CLK_ENABLE BIT16
> > > +
> > > +#define UHSEXT_SAMPLE_PHASE(x) (((x) & 0x1f) << 16)
> > > +#define UHSEXT_SAMPLE_DRVPHASE(x) (((x) & 0x1f) << 21)
> > > +#define UHSEXT_SAMPLE_DLY(x) (((x) & 0x1f) << 26)
> > > +
> > > +#define DWMMC_DMA_BUF_SIZE (512 * 8)
> > > +#define DWMMC_FIFO_THRESHOLD 16
> > > +
> > > +#define DWMMC_INIT_CLOCK_FREQ 400 /* KHz */
> > > +
> > > +//
> > > +// The transfer modes supported by SD Host Controller
> > > +// Simplified Spec 3.0 Table 1-2
> > > +//
> > > +typedef enum {
> > > + SdMmcNoData,
> > > + SdMmcPioMode,
> > > + SdMmcSdmaMode,
> > > + SdMmcAdmaMode
> > > +} DW_MMC_HC_TRANSFER_MODE;
> > > +
> > > +//
> > > +// The maximum data length of each descriptor line
> > > +//
> > > +#define ADMA_MAX_DATA_PER_LINE 0x10000
> > > +
> > > +typedef struct {
> > > + UINT32 Des0;
> > > + UINT32 Des1;
> > > + UINT32 Des2;
> > > + UINT32 Des3;
> > > +} DW_MMC_HC_DMA_DESC_LINE;
> > > +
> > > +#define SD_MMC_SDMA_BOUNDARY 512 * 1024
> > > +#define SD_MMC_SDMA_ROUND_UP(x, n) (((x) + n) & ~(n - 1))
> > > +
> > > +typedef struct {
> > > + UINT8 FirstBar:3; // bit 0:2
> > > + UINT8 Reserved:1; // bit 3
> > > + UINT8 SlotNum:3; // bit 4:6
> > > + UINT8 Reserved1:1; // bit 7
> > > +} DW_MMC_HC_SLOT_INFO;
> > > +
> > > +/**
> > > + Dump the content of SD/MMC host controller's Capability Register.
> > > +
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[in] Capability The buffer to store the capability data.
> > > +
> > > +**/
> > > +VOID
> > > +DumpCapabilityReg (
> > > + IN UINT8 Slot,
> > > + IN DW_MMC_HC_SLOT_CAP *Capability
> > > + );
> > > +
> > > +#if 0
> > > +/**
> > > + Read SlotInfo register from SD/MMC host controller pci config space.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[out] FirstBar The buffer to store the first BAR value.
> > > + @param[out] SlotNum The buffer to store the supported slot
> number.
> > > +
> > > + @retval EFI_SUCCESS The operation succeeds.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcGetSlotInfo (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + OUT UINT8 *FirstBar,
> > > + OUT UINT8 *SlotNum
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Read/Write specified SD/MMC host controller mmio register.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] BarIndex The BAR index of the standard PCI
> > Configuration
> > > + header to use as the base address for the memory
> > > + operation to perform.
> > > + @param[in] Offset The offset within the selected BAR to start the
> > > + memory operation.
> > > + @param[in] Read A boolean to indicate it's read or write
> > operation.
> > > + @param[in] Count The width of the mmio register in bytes.
> > > + Must be 1, 2 , 4 or 8 bytes.
> > > + @param[in, out] Data For read operations, the destination buffer
> to
> > store
> > > + the results. For write operations, the source buffer
> > > + to write data from. The caller is responsible for
> > > + having ownership of the data buffer and ensuring its
> > > + size not less than Count bytes.
> > > +
> > > + @retval EFI_INVALID_PARAMETER The PciIo or Data is NULL or the
> Count
> > is not valid.
> > > + @retval EFI_SUCCESS The read/write operation succeeds.
> > > + @retval Others The read/write operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcRwMmio (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 BarIndex,
> > > + IN UINT32 Offset,
> > > + IN BOOLEAN Read,
> > > + IN UINT8 Count,
> > > + IN OUT VOID *Data
> > > + );
> > > +#else
> > > +/**
> > > + Read/Write specified SD/MMC host controller mmio register.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Offset The offset within the selected BAR to start the
> > > + memory operation.
> > > + @param[in] Read A boolean to indicate it's read or write
> > operation.
> > > + @param[in] Count The width of the mmio register in bytes.
> > > + Must be 1, 2 , 4 or 8 bytes.
> > > + @param[in, out] Data For read operations, the destination buffer
> to
> > store
> > > + the results. For write operations, the source buffer
> > > + to write data from. The caller is responsible for
> > > + having ownership of the data buffer and ensuring its
> > > + size not less than Count bytes.
> > > +
> > > + @retval EFI_INVALID_PARAMETER The PciIo or Data is NULL or the
> Count
> > is not valid.
> > > + @retval EFI_SUCCESS The read/write operation succeeds.
> > > + @retval Others The read/write operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcRwMmio (
> > > + IN UINTN DevBase,
> > > + IN UINT32 Offset,
> > > + IN BOOLEAN Read,
> > > + IN UINT8 Count,
> > > + IN OUT VOID *Data
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Do OR operation with the value of the specified SD/MMC host
> controller
> > mmio register.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] BarIndex The BAR index of the standard PCI
> > Configuration
> > > + header to use as the base address for the memory
> > > + operation to perform.
> > > + @param[in] Offset The offset within the selected BAR to start the
> > > + memory operation.
> > > + @param[in] Count The width of the mmio register in bytes.
> > > + Must be 1, 2 , 4 or 8 bytes.
> > > + @param[in] OrData The pointer to the data used to do OR
> > operation.
> > > + The caller is responsible for having ownership of
> > > + the data buffer and ensuring its size not less than
> > > + Count bytes.
> > > +
> > > + @retval EFI_INVALID_PARAMETER The PciIo or OrData is NULL or the
> > Count is not valid.
> > > + @retval EFI_SUCCESS The OR operation succeeds.
> > > + @retval Others The OR operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcOrMmio (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 BarIndex,
> > > + IN UINT32 Offset,
> > > + IN UINT8 Count,
> > > + IN VOID *OrData
> > > + );
> > > +#else
> > > +/**
> > > + Do OR operation with the value of the specified SD/MMC host
> controller
> > mmio register.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] BarIndex The BAR index of the standard PCI
> > Configuration
> > > + header to use as the base address for the memory
> > > + operation to perform.
> > > + @param[in] Offset The offset within the selected BAR to start the
> > > + memory operation.
> > > + @param[in] Count The width of the mmio register in bytes.
> > > + Must be 1, 2 , 4 or 8 bytes.
> > > + @param[in] OrData The pointer to the data used to do OR
> > operation.
> > > + The caller is responsible for having ownership of
> > > + the data buffer and ensuring its size not less than
> > > + Count bytes.
> > > +
> > > + @retval EFI_INVALID_PARAMETER The PciIo or OrData is NULL or the
> > Count is not valid.
> > > + @retval EFI_SUCCESS The OR operation succeeds.
> > > + @retval Others The OR operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcOrMmio (
> > > + IN UINTN DevBase,
> > > + IN UINT32 Offset,
> > > + IN UINT8 Count,
> > > + IN VOID *OrData
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Do AND operation with the value of the specified SD/MMC host
> > controller mmio register.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] BarIndex The BAR index of the standard PCI
> > Configuration
> > > + header to use as the base address for the memory
> > > + operation to perform.
> > > + @param[in] Offset The offset within the selected BAR to start the
> > > + memory operation.
> > > + @param[in] Count The width of the mmio register in bytes.
> > > + Must be 1, 2 , 4 or 8 bytes.
> > > + @param[in] AndData The pointer to the data used to do AND
> > operation.
> > > + The caller is responsible for having ownership of
> > > + the data buffer and ensuring its size not less than
> > > + Count bytes.
> > > +
> > > + @retval EFI_INVALID_PARAMETER The PciIo or AndData is NULL or the
> > Count is not valid.
> > > + @retval EFI_SUCCESS The AND operation succeeds.
> > > + @retval Others The AND operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcAndMmio (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 BarIndex,
> > > + IN UINT32 Offset,
> > > + IN UINT8 Count,
> > > + IN VOID *AndData
> > > + );
> > > +#else
> > > +/**
> > > + Do AND operation with the value of the specified SD/MMC host
> > controller mmio register.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Offset The offset within the selected BAR to start the
> > > + memory operation.
> > > + @param[in] Count The width of the mmio register in bytes.
> > > + Must be 1, 2 , 4 or 8 bytes.
> > > + @param[in] AndData The pointer to the data used to do AND
> > operation.
> > > + The caller is responsible for having ownership of
> > > + the data buffer and ensuring its size not less than
> > > + Count bytes.
> > > +
> > > + @retval EFI_INVALID_PARAMETER The PciIo or AndData is NULL or the
> > Count is not valid.
> > > + @retval EFI_SUCCESS The AND operation succeeds.
> > > + @retval Others The AND operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcAndMmio (
> > > + IN UINTN DevBase,
> > > + IN UINT32 Offset,
> > > + IN UINT8 Count,
> > > + IN VOID *AndData
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Wait for the value of the specified MMIO register set to the test value.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] BarIndex The BAR index of the standard PCI
> > Configuration
> > > + header to use as the base address for the memory
> > > + operation to perform.
> > > + @param[in] Offset The offset within the selected BAR to start the
> > > + memory operation.
> > > + @param[in] Count The width of the mmio register in bytes.
> > > + Must be 1, 2, 4 or 8 bytes.
> > > + @param[in] MaskValue The mask value of memory.
> > > + @param[in] TestValue The test value of memory.
> > > + @param[in] Timeout The time out value for wait memory set, uses
> 1
> > > + microsecond as a unit.
> > > +
> > > + @retval EFI_TIMEOUT The MMIO register hasn't expected value in
> > timeout
> > > + range.
> > > + @retval EFI_SUCCESS The MMIO register has expected value.
> > > + @retval Others The MMIO operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcWaitMmioSet (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 BarIndex,
> > > + IN UINT32 Offset,
> > > + IN UINT8 Count,
> > > + IN UINT64 MaskValue,
> > > + IN UINT64 TestValue,
> > > + IN UINT64 Timeout
> > > + );
> > > +#else
> > > +/**
> > > + Wait for the value of the specified MMIO register set to the test value.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Offset The offset within the selected BAR to start the
> > > + memory operation.
> > > + @param[in] Count The width of the mmio register in bytes.
> > > + Must be 1, 2, 4 or 8 bytes.
> > > + @param[in] MaskValue The mask value of memory.
> > > + @param[in] TestValue The test value of memory.
> > > + @param[in] Timeout The time out value for wait memory set, uses
> 1
> > > + microsecond as a unit.
> > > +
> > > + @retval EFI_TIMEOUT The MMIO register hasn't expected value in
> > timeout
> > > + range.
> > > + @retval EFI_SUCCESS The MMIO register has expected value.
> > > + @retval Others The MMIO operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcWaitMmioSet (
> > > + IN UINTN DevBase,
> > > + IN UINT32 Offset,
> > > + IN UINT8 Count,
> > > + IN UINT64 MaskValue,
> > > + IN UINT64 TestValue,
> > > + IN UINT64 Timeout
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Software reset the specified SD/MMC host controller.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > +
> > > + @retval EFI_SUCCESS The software reset executes successfully.
> > > + @retval Others The software reset fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcReset (
> > > +fark
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 Slot,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + );
> > > +#else
> > > +/**
> > > + Software reset the specified SD/MMC host controller.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > +
> > > + @retval EFI_SUCCESS The software reset executes successfully.
> > > + @retval Others The software reset fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcReset (
> > > + IN UINTN DevBase,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Set all interrupt status bits in Normal and Error Interrupt Status Enable
> > > + register.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > +
> > > + @retval EFI_SUCCESS The operation executes successfully.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcEnableInterrupt (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 Slot
> > > + );
> > > +#else
> > > +/**
> > > + Set all interrupt status bits in Normal and Error Interrupt Status Enable
> > > + register.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > +
> > > + @retval EFI_SUCCESS The operation executes successfully.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcEnableInterrupt (
> > > + IN UINTN DevBase
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Get the capability data from the specified slot.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[out] Capability The buffer to store the capability data.
> > > +
> > > + @retval EFI_SUCCESS The operation executes successfully.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcGetCapability (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN EFI_HANDLE Controller,
> > > + IN UINT8 Slot,
> > > + OUT DW_MMC_HC_SLOT_CAP *Capability
> > > + );
> > > +#else
> > > +/**
> > > + Get the capability data from the specified slot.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[out] Capability The buffer to store the capability data.
> > > +
> > > + @retval EFI_SUCCESS The operation executes successfully.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcGetCapability (
> > > + IN UINTN DevBase,
> > > + IN EFI_HANDLE Controller,
> > > + IN UINT8 Slot,
> > > + OUT DW_MMC_HC_SLOT_CAP *Capability
> > > + );
> > > +#endif
> > > +
> > > +#if 0
> > > +/**
> > > + Get the maximum current capability data from the specified slot.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[out] MaxCurrent The buffer to store the maximum current
> > capability data.
> > > +
> > > + @retval EFI_SUCCESS The operation executes successfully.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcGetMaxCurrent (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 Slot,
> > > + OUT UINT64 *MaxCurrent
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Detect whether there is a SD/MMC card attached at the specified
> > SD/MMC host controller
> > > + slot.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.1 for details.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[out] MediaPresent The pointer to the media present
> boolean
> > value.
> > > +
> > > + @retval EFI_SUCCESS There is no media change happened.
> > > + @retval EFI_MEDIA_CHANGED There is media change happened.
> > > + @retval Others The detection fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcCardDetect (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN EFI_HANDLE Controller,
> > > + IN UINT8 Slot,
> > > + OUT BOOLEAN *MediaPresent
> > > + );
> > > +#else
> > > +/**
> > > + Detect whether there is a SD/MMC card attached at the specified
> > SD/MMC host controller
> > > + slot.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.1 for details.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[out] MediaPresent The pointer to the media present
> boolean
> > value.
> > > +
> > > + @retval EFI_SUCCESS There is no media change happened.
> > > + @retval EFI_MEDIA_CHANGED There is media change happened.
> > > + @retval Others The detection fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcCardDetect (
> > > + IN UINTN DevBase,
> > > + IN EFI_HANDLE Controller,
> > > + IN UINT8 Slot,
> > > + OUT BOOLEAN *MediaPresent
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Stop SD/MMC card clock.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.2.2 for details.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > +
> > > + @retval EFI_SUCCESS Succeed to stop SD/MMC clock.
> > > + @retval Others Fail to stop SD/MMC clock.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcStopClock (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 Slot
> > > + );
> > > +
> > > +/**
> > > + SD/MMC card clock supply.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.2.1 for details.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[in] ClockFreq The max clock frequency to be set. The unit is
> > KHz.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The clock is supplied successfully.
> > > + @retval Others The clock isn't supplied successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcClockSupply (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 Slot,
> > > + IN UINT64 ClockFreq,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + );
> > > +#else
> > > +/**
> > > + Stop SD/MMC card clock.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.2.2 for details.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > +
> > > + @retval EFI_SUCCESS Succeed to stop SD/MMC clock.
> > > + @retval Others Fail to stop SD/MMC clock.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcStopClock (
> > > + IN UINTN DevBase
> > > + );
> > > +
> > > +/**
> > > + SD/MMC card clock supply.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.2.1 for details.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] ClockFreq The max clock frequency to be set. The unit is
> > KHz.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The clock is supplied successfully.
> > > + @retval Others The clock isn't supplied successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcClockSupply (
> > > + IN UINTN DevBase,
> > > + IN UINT64 ClockFreq,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + );
> > > +#endif
> > > +
> > > +#if 0
> > > +/**
> > > + SD/MMC bus power control.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.3 for details.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[in] PowerCtrl The value setting to the power control
> register.
> > > +
> > > + @retval TRUE There is a SD/MMC card attached.
> > > + @retval FALSE There is no a SD/MMC card attached.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcPowerControl (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 Slot,
> > > + IN UINT8 PowerCtrl
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Set the SD/MMC bus width.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.4 for details.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[in] BusWidth The bus width used by the SD/MMC device, it
> > must be 1, 4 or 8.
> > > +
> > > + @retval EFI_SUCCESS The bus width is set successfully.
> > > + @retval Others The bus width isn't set successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcSetBusWidth (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 Slot,
> > > + IN BOOLEAN IsDdr,
> > > + IN UINT16 BusWidth
> > > + );
> > > +#else
> > > +/**
> > > + Set the SD/MMC bus width.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.4 for details.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] BusWidth The bus width used by the SD/MMC device, it
> > must be 1, 4 or 8.
> > > +
> > > + @retval EFI_SUCCESS The bus width is set successfully.
> > > + @retval Others The bus width isn't set successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcSetBusWidth (
> > > + IN UINTN DevBase,
> > > + IN BOOLEAN IsDdr,
> > > + IN UINT16 BusWidth
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Supply SD/MMC card with lowest clock frequency at initialization.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The clock is supplied successfully.
> > > + @retval Others The clock isn't supplied successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitClockFreq (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 Slot,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + );
> > > +#else
> > > +/**
> > > + Supply SD/MMC card with lowest clock frequency at initialization.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The clock is supplied successfully.
> > > + @retval Others The clock isn't supplied successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitClockFreq (
> > > + IN UINTN DevBase,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Supply SD/MMC card with maximum voltage at initialization.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.3 for details.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The voltage is supplied successfully.
> > > + @retval Others The voltage isn't supplied successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitPowerVoltage (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 Slot,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + );
> > > +#else
> > > +/**
> > > + Supply SD/MMC card with maximum voltage at initialization.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.3 for details.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The voltage is supplied successfully.
> > > + @retval Others The voltage isn't supplied successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitPowerVoltage (
> > > + IN UINTN DevBase,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Initialize the Timeout Control register with most conservative value at
> > initialization.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 2.2.15 for details.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > +
> > > + @retval EFI_SUCCESS The timeout control register is configured
> > successfully.
> > > + @retval Others The timeout control register isn't configured
> > successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitTimeoutCtrl (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 Slot
> > > + );
> > > +#else
> > > +/**
> > > + Initialize the Timeout Control register with most conservative value at
> > initialization.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 2.2.15 for details.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > +
> > > + @retval EFI_SUCCESS The timeout control register is configured
> > successfully.
> > > + @retval Others The timeout control register isn't configured
> > successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitTimeoutCtrl (
> > > + IN UINTN DevBase
> > > + );
> > > +#endif
> > > +
> > > +#ifdef DWMMC_PCI
> > > +/**
> > > + Initial SD/MMC host controller with lowest clock frequency, max power
> > and max timeout value
> > > + at initialization.
> > > +
> > > + @param[in] PciIo The PCI IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command to.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The host controller is initialized successfully.
> > > + @retval Others The host controller isn't initialized successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitHost (
> > > + IN EFI_PCI_IO_PROTOCOL *PciIo,
> > > + IN UINT8 Slot,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + );
> > > +#else
> > > +/**
> > > + Initial SD/MMC host controller with lowest clock frequency, max power
> > and
> > > + max timeout value at initialization.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The host controller is initialized successfully.
> > > + @retval Others The host controller isn't initialized successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitHost (
> > > + IN UINTN DevBase,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + );
> > > +#endif
> > > +
> > > +#endif /* _DW_MMC_HCI_H_ */
> > > diff --git a/EmbeddedPkg/Include/Protocol/PlatformDwMmc.h
> > b/EmbeddedPkg/Include/Protocol/PlatformDwMmc.h
> > > new file mode 100644
> > > index 000000000000..acbc3e153dac
> > > --- /dev/null
> > > +++ b/EmbeddedPkg/Include/Protocol/PlatformDwMmc.h
> > > @@ -0,0 +1,79 @@
> > > +/** @file
> > > +
> > > + Copyright (c) 2018, Linaro. All rights reserved.
> > > +
> > > + This program and the accompanying materials are licensed and made
> > available
> > > + under the terms and conditions of the BSD License which accompanies
> > this
> > > + distribution. The full text of the license may be found at
> > > + http://opensource.org/licenses/bsd-license.php
> > > +
> > > + THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS"
> > BASIS,
> > > + WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER
> > EXPRESS OR IMPLIED.
> > > +
> > > +**/
> > > +
> > > +#ifndef __PLATFORM_DW_MMC_H__
> > > +#define __PLATFORM_DW_MMC_H__
> > > +
> > > +typedef enum {
> > > + RemovableSlot,
> > > + EmbeddedSlot,
> > > + SharedBusSlot,
> > > + UnknownSlot
> > > +} EFI_SD_MMC_SLOT_TYPE;
> > > +
> > > +typedef enum {
> > > + UnknownCardType,
> > > + SdCardType,
> > > + SdioCardType,
> > > + MmcCardType,
> > > + EmmcCardType
> > > +} SD_MMC_CARD_TYPE;
> > > +
> > > +typedef struct {
> > > + UINT32 DefaultSpeed:1; // bit 0
> > > + UINT32 HighSpeed:1; // bit 1
> > > + UINT32 Sdr12:1; // bit 2
> > > + UINT32 Sdr25:1; // bit 3
> > > + UINT32 Sdr50:1; // bit 4
> > > + UINT32 Sdr104:1; // bit 5
> > > + UINT32 Ddr50:1; // bit 6
> > > + UINT32 SysBus64:1; // bit 7
> > > + UINT32 BusWidth:4; // bit 11:8
> > > + UINT32 SlotType:2; // bit 13:12
> > > + UINT32 CardType:3; // bit 16:14
> > > + UINT32 Voltage18:1; // bit 17
> > > + UINT32 Voltage30:1; // bit 18
> > > + UINT32 Voltage33:1; // bit 19
> > > + UINT32 BaseClkFreq;
> > > + EFI_HANDLE Controller;
> > > +} DW_MMC_HC_SLOT_CAP;
> > > +
> > > +//
> > > +// Protocol interface structure
> > > +//
> > > +typedef struct _PLATFORM_DW_MMC_PROTOCOL
> > PLATFORM_DW_MMC_PROTOCOL;
> > > +
> > > +typedef
> > > +EFI_STATUS
> > > +(EFIAPI *PLATFORM_DW_MMC_GET_CAPABILITY) (
> > > + IN EFI_HANDLE Controller,
> > > + IN UINT8 Slot,
> > > + OUT DW_MMC_HC_SLOT_CAP *Capability
> > > + );
> > > +
> > > +typedef
> > > +BOOLEAN
> > > +(EFIAPI *PLATFORM_DW_MMC_CARD_DETECT) (
> > > + IN EFI_HANDLE Controller,
> > > + IN UINT8 Slot
> > > + );
> > > +
> > > +struct _PLATFORM_DW_MMC_PROTOCOL {
> > > + PLATFORM_DW_MMC_GET_CAPABILITY GetCapability;
> > > + PLATFORM_DW_MMC_CARD_DETECT CardDetect;
> > > +};
> > > +
> > > +extern EFI_GUID gPlatformDwMmcProtocolGuid;
> > > +
> > > +#endif /* __PLATFORM_DW_MMC_H__ */
> > > diff --git a/EmbeddedPkg/Drivers/DwMmcHcDxe/ComponentName.c
> > b/EmbeddedPkg/Drivers/DwMmcHcDxe/ComponentName.c
> > > new file mode 100644
> > > index 000000000000..1edade69d091
> > > --- /dev/null
> > > +++ b/EmbeddedPkg/Drivers/DwMmcHcDxe/ComponentName.c
> > > @@ -0,0 +1,214 @@
> > > +/** @file
> > > + UEFI Component Name(2) protocol implementation for Designware
> > SD/MMC host
> > > + controller driver.
> > > +
> > > + Copyright (c) 2015, Intel Corporation. All rights reserved.<BR>
> > > + Copyright (c) 2018, Linaro Ltd. All rights reserved.<BR>
> > > +
> > > + This program and the accompanying materials are licensed and made
> > available
> > > + under the terms and conditions of the BSD License which accompanies
> > this
> > > + distribution. The full text of the license may be found at
> > > + http://opensource.org/licenses/bsd-license.php
> > > +
> > > + THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS"
> > BASIS,
> > > + WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER
> > EXPRESS OR IMPLIED.
> > > +
> > > +**/
> > > +
> > > +#include "DwMmcHcDxe.h"
> > > +
> > > +//
> > > +// EFI Component Name Protocol
> > > +//
> > > +GLOBAL_REMOVE_IF_UNREFERENCED
> > EFI_COMPONENT_NAME_PROTOCOL gDwMmcHcComponentName = {
> > > + DwMmcHcComponentNameGetDriverName,
> > > + DwMmcHcComponentNameGetControllerName,
> > > + "eng"
> > > +};
> > > +
> > > +//
> > > +// EFI Component Name 2 Protocol
> > > +//
> > > +GLOBAL_REMOVE_IF_UNREFERENCED
> > EFI_COMPONENT_NAME2_PROTOCOL gDwMmcHcComponentName2 = {
> > > + (EFI_COMPONENT_NAME2_GET_DRIVER_NAME)
> > DwMmcHcComponentNameGetDriverName,
> > > + (EFI_COMPONENT_NAME2_GET_CONTROLLER_NAME)
> > DwMmcHcComponentNameGetControllerName,
> > > + "en"
> > > +};
> > > +
> > > +GLOBAL_REMOVE_IF_UNREFERENCED EFI_UNICODE_STRING_TABLE
> > mDwMmcHcDriverNameTable[] = {
> > > + { "eng;en", L"Designware Sd/Mmc Host Controller Driver" },
> > > + { NULL , NULL }
> > > +};
> > > +
> > > +GLOBAL_REMOVE_IF_UNREFERENCED EFI_UNICODE_STRING_TABLE
> > mDwMmcHcControllerNameTable[] = {
> > > + { "eng;en", L"Designware Sd/Mmc Host Controller" },
> > > + { NULL , NULL }
> > > +};
> > > +
> > > +/**
> > > + Retrieves a Unicode string that is the user readable name of the driver.
> > > +
> > > + This function retrieves the user readable name of a driver in the form
> of
> > a
> > > + Unicode string. If the driver specified by This has a user readable name
> in
> > > + the language specified by Language, then a pointer to the driver name
> is
> > > + returned in DriverName, and EFI_SUCCESS is returned. If the driver
> > specified
> > > + by This does not support the language specified by Language,
> > > + then EFI_UNSUPPORTED is returned.
> > > +
> > > + @param This[in] A pointer to the
> > EFI_COMPONENT_NAME2_PROTOCOL or
> > > + EFI_COMPONENT_NAME_PROTOCOL instance.
> > > +
> > > + @param Language[in] A pointer to a Null-terminated ASCII string
> > > + array indicating the language. This is the
> > > + language of the driver name that the caller is
> > > + requesting, and it must match one of the
> > > + languages specified in SupportedLanguages. The
> > > + number of languages supported by a driver is up
> > > + to the driver writer. Language is specified
> > > + in RFC 4646 or ISO 639-2 language code format.
> > > +
> > > + @param DriverName[out] A pointer to the Unicode string to return.
> > > + This Unicode string is the name of the
> > > + driver specified by This in the language
> > > + specified by Language.
> > > +
> > > + @retval EFI_SUCCESS The Unicode string for the Driver specified
> by
> > > + This and the language specified by Language was
> > > + returned in DriverName.
> > > +
> > > + @retval EFI_INVALID_PARAMETER Language is NULL.
> > > +
> > > + @retval EFI_INVALID_PARAMETER DriverName is NULL.
> > > +
> > > + @retval EFI_UNSUPPORTED The driver specified by This does not
> > support
> > > + the language specified by Language.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcComponentNameGetDriverName (
> > > + IN EFI_COMPONENT_NAME_PROTOCOL *This,
> > > + IN CHAR8 *Language,
> > > + OUT CHAR16 **DriverName
> > > + )
> > > +{
> > > + return LookupUnicodeString2 (
> > > + Language,
> > > + This->SupportedLanguages,
> > > + mDwMmcHcDriverNameTable,
> > > + DriverName,
> > > + (BOOLEAN)(This == &gDwMmcHcComponentName)
> > > + );
> > > +}
> > > +
> > > +/**
> > > + Retrieves a Unicode string that is the user readable name of the
> > controller
> > > + that is being managed by a driver.
> > > +
> > > + This function retrieves the user readable name of the controller
> specified
> > by
> > > + ControllerHandle and ChildHandle in the form of a Unicode string. If the
> > > + driver specified by This has a user readable name in the language
> > specified by
> > > + Language, then a pointer to the controller name is returned in
> > ControllerName,
> > > + and EFI_SUCCESS is returned. If the driver specified by This is not
> > currently
> > > + managing the controller specified by ControllerHandle and ChildHandle,
> > > + then EFI_UNSUPPORTED is returned. If the driver specified by This
> does
> > not
> > > + support the language specified by Language, then EFI_UNSUPPORTED
> is
> > returned.
> > > +
> > > + @param This[in] A pointer to the
> > EFI_COMPONENT_NAME2_PROTOCOL or
> > > + EFI_COMPONENT_NAME_PROTOCOL instance.
> > > +
> > > + @param ControllerHandle[in] The handle of a controller that the
> driver
> > > + specified by This is managing. This handle
> > > + specifies the controller whose name is to be
> > > + returned.
> > > +
> > > + @param ChildHandle[in] The handle of the child controller to
> retrieve
> > > + the name of. This is an optional parameter that
> > > + may be NULL. It will be NULL for device
> > > + drivers. It will also be NULL for a bus drivers
> > > + that wish to retrieve the name of the bus
> > > + controller. It will not be NULL for a bus
> > > + driver that wishes to retrieve the name of a
> > > + child controller.
> > > +
> > > + @param Language[in] A pointer to a Null-terminated ASCII string
> > > + array indicating the language. This is the
> > > + language of the driver name that the caller is
> > > + requesting, and it must match one of the
> > > + languages specified in SupportedLanguages. The
> > > + number of languages supported by a driver is up
> > > + to the driver writer. Language is specified in
> > > + RFC 4646 or ISO 639-2 language code format.
> > > +
> > > + @param ControllerName[out] A pointer to the Unicode string to
> > return.
> > > + This Unicode string is the name of the
> > > + controller specified by ControllerHandle and
> > > + ChildHandle in the language specified by
> > > + Language from the point of view of the driver
> > > + specified by This.
> > > +
> > > + @retval EFI_SUCCESS The Unicode string for the user readable
> > name in
> > > + the language specified by Language for the
> > > + driver specified by This was returned in
> > > + DriverName.
> > > +
> > > + @retval EFI_INVALID_PARAMETER ControllerHandle is not a valid
> > EFI_HANDLE.
> > > +
> > > + @retval EFI_INVALID_PARAMETER ChildHandle is not NULL and it is not
> a
> > valid
> > > + EFI_HANDLE.
> > > +
> > > + @retval EFI_INVALID_PARAMETER Language is NULL.
> > > +
> > > + @retval EFI_INVALID_PARAMETER ControllerName is NULL.
> > > +
> > > + @retval EFI_UNSUPPORTED The driver specified by This is not
> > currently
> > > + managing the controller specified by
> > > + ControllerHandle and ChildHandle.
> > > +
> > > + @retval EFI_UNSUPPORTED The driver specified by This does not
> > support
> > > + the language specified by Language.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcComponentNameGetControllerName (
> > > + IN EFI_COMPONENT_NAME_PROTOCOL *This,
> > > + IN EFI_HANDLE ControllerHandle,
> > > + IN EFI_HANDLE ChildHandle, OPTIONAL
> > > + IN CHAR8 *Language,
> > > + OUT CHAR16 **ControllerName
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > +
> > > + if (Language == NULL || ControllerName == NULL) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + //
> > > + // This is a device driver, so ChildHandle must be NULL.
> > > + //
> > > + if (ChildHandle != NULL) {
> > > + return EFI_UNSUPPORTED;
> > > + }
> > > +
> > > + //
> > > + // Make sure this driver is currently managing ControllerHandle
> > > + //
> > > + Status = EfiTestManagedDevice (
> > > + ControllerHandle,
> > > + gDwMmcHcDriverBinding.DriverBindingHandle,
> > > + &gEfiPciIoProtocolGuid
> > > + );
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + return LookupUnicodeString2 (
> > > + Language,
> > > + This->SupportedLanguages,
> > > + mDwMmcHcControllerNameTable,
> > > + ControllerName,
> > > + (BOOLEAN)(This == &gDwMmcHcComponentName)
> > > + );
> > > +}
> > > diff --git a/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.c
> > b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.c
> > > new file mode 100644
> > > index 000000000000..aea12170d2cc
> > > --- /dev/null
> > > +++ b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHcDxe.c
> > > @@ -0,0 +1,1296 @@
> > > +/** @file
> > > + This driver is used to manage Designware SD/MMC host controller.
> > > +
> > > + It would expose EFI_SD_MMC_PASS_THRU_PROTOCOL for upper
> layer
> > use.
> > > +
> > > + Copyright (c) 2015 - 2021, Intel Corporation. All rights reserved.<BR>
> > > + Copyright (C) 2016 Marvell International Ltd. All rigths reserved.<BR>
> > > + Copyright (C) 2018, Linaro Ltd. All rigths reserved.<BR>
> > > +
> > > + This program and the accompanying materials
> > > + are licensed and made available under the terms and conditions of the
> > BSD License
> > > + which accompanies this distribution. The full text of the license may be
> > found at
> > > + http://opensource.org/licenses/bsd-license.php
> > > +
> > > + THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS"
> > BASIS,
> > > + WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER
> > EXPRESS OR IMPLIED.
> > > +
> > > +**/
> > > +
> > > +#include <Library/BaseMemoryLib.h>
> > > +#include <Library/DebugLib.h>
> > > +#include <Library/DevicePathLib.h>
> > > +#include <Library/IoLib.h>
> > > +#include <Library/MemoryAllocationLib.h>
> > > +#include <Protocol/NonDiscoverableDevice.h>
> > > +#include <Library/UefiBootServicesTableLib.h>
> > > +#include <Library/UefiDriverEntryPoint.h>
> > > +
> > > +#include <Protocol/DevicePath.h>
> > > +#include <Protocol/PlatformDwMmc.h>
> > > +
> > > +#include "DwMmcHcDxe.h"
> > > +
> > > +//
> > > +// Driver Global Variables
> > > +//
> > > +EFI_DRIVER_BINDING_PROTOCOL gDwMmcHcDriverBinding = {
> > > + DwMmcHcDriverBindingSupported,
> > > + DwMmcHcDriverBindingStart,
> > > + DwMmcHcDriverBindingStop,
> > > + 0x10,
> > > + NULL,
> > > + NULL
> > > +};
> > > +
> > > +//
> > > +// Template for Designware SD/MMC host controller private data.
> > > +//
> > > +DW_MMC_HC_PRIVATE_DATA gDwMmcHcTemplate = {
> > > + DW_MMC_HC_PRIVATE_SIGNATURE, // Signature
> > > + NULL, // ControllerHandle
> > > + 0x0, // Mmio base address
> > > + { // PassThru
> > > + sizeof (UINT32),
> > > + DwMmcPassThruPassThru,
> > > + DwMmcPassThruGetNextSlot,
> > > + DwMmcPassThruBuildDevicePath,
> > > + DwMmcPassThruGetSlotNumber,
> > > + DwMmcPassThruResetDevice
> > > + },
> > > + NULL, // PlatformDwMmc
> > > + 0, // PreviousSlot
> > > + NULL, // TimerEvent
> > > + NULL, // ConnectEvent
> > > + // Queue
> > > + INITIALIZE_LIST_HEAD_VARIABLE (gDwMmcHcTemplate.Queue),
> > > + { // Slot
> > > + {0, UnknownSlot, 0, 0, 0}
> > > + },
> > > + { // Capability
> > > + {0}
> > > + },
> > > + { // MaxCurrent
> > > + 0
> > > + },
> > > + 0 // ControllerVersion
> > > +};
> > > +
> > > +SD_DEVICE_PATH mSdDpTemplate = {
> > > + {
> > > + MESSAGING_DEVICE_PATH,
> > > + MSG_SD_DP,
> > > + {
> > > + (UINT8) (sizeof (SD_DEVICE_PATH)),
> > > + (UINT8) ((sizeof (SD_DEVICE_PATH)) >> 8)
> > > + }
> > > + },
> > > + 0
> > > +};
> > > +
> > > +EMMC_DEVICE_PATH mEmmcDpTemplate = {
> > > + {
> > > + MESSAGING_DEVICE_PATH,
> > > + MSG_EMMC_DP,
> > > + {
> > > + (UINT8) (sizeof (EMMC_DEVICE_PATH)),
> > > + (UINT8) ((sizeof (EMMC_DEVICE_PATH)) >> 8)
> > > + }
> > > + },
> > > + 0
> > > +};
> > > +
> > > +//
> > > +// Prioritized function list to detect card type.
> > > +// User could add other card detection logic here.
> > > +//
> > > +DWMMC_CARD_TYPE_DETECT_ROUTINE
> > mCardTypeDetectRoutineTable[] = {
> > > + EmmcIdentification,
> > > + SdCardIdentification,
> > > + NULL
> > > +};
> > > +
> > > +/**
> > > + The entry point for SD host controller driver, used to install this driver
> on
> > the ImageHandle.
> > > +
> > > + @param[in] ImageHandle The firmware allocated handle for this
> driver
> > image.
> > > + @param[in] SystemTable Pointer to the EFI system table.
> > > +
> > > + @retval EFI_SUCCESS Driver loaded.
> > > + @retval other Driver not loaded.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +InitializeDwMmcHcDxe (
> > > + IN EFI_HANDLE ImageHandle,
> > > + IN EFI_SYSTEM_TABLE *SystemTable
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > +
> > > + Status = EfiLibInstallDriverBindingComponentName2 (
> > > + ImageHandle,
> > > + SystemTable,
> > > + &gDwMmcHcDriverBinding,
> > > + ImageHandle,
> > > + &gDwMmcHcComponentName,
> > > + &gDwMmcHcComponentName2
> > > + );
> > > + ASSERT_EFI_ERROR (Status);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Call back function when the timer event is signaled.
> > > +
> > > + @param[in] Event The Event this notify function registered to.
> > > + @param[in] Context Pointer to the context data registered to the
> > > + Event.
> > > +
> > > +**/
> > > +VOID
> > > +EFIAPI
> > > +ProcessAsyncTaskList (
> > > + IN EFI_EVENT Event,
> > > + IN VOID* Context
> > > + )
> > > +{
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > + LIST_ENTRY *Link;
> > > + DW_MMC_HC_TRB *Trb;
> > > + EFI_STATUS Status;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet;
> > > + BOOLEAN InfiniteWait;
> > > + EFI_EVENT TrbEvent;
> > > +
> > > + Private = (DW_MMC_HC_PRIVATE_DATA *)Context;
> > > +
> > > + //
> > > + // Check if the first entry in the async I/O queue is done or not.
> > > + //
> > > + Status = EFI_SUCCESS;
> > > + Trb = NULL;
> > > + Link = GetFirstNode (&Private->Queue);
> > > + if (!IsNull (&Private->Queue, Link)) {
> > > + Trb = DW_MMC_HC_TRB_FROM_THIS (Link);
> > > + if (!Private->Slot[Trb->Slot].MediaPresent) {
> > > + Status = EFI_NO_MEDIA;
> > > + goto Done;
> > > + }
> > > + if (!Trb->Started) {
> > > + //
> > > + // Check whether the cmd/data line is ready for transfer.
> > > + //
> > > + Status = DwMmcCheckTrbEnv (Private, Trb);
> > > + if (!EFI_ERROR (Status)) {
> > > + Trb->Started = TRUE;
> > > + Status = DwMmcExecTrb (Private, Trb);
> > > + if (EFI_ERROR (Status)) {
> > > + goto Done;
> > > + }
> > > + } else {
> > > + goto Done;
> > > + }
> > > + }
> > > + Status = DwMmcCheckTrbResult (Private, Trb);
> > > + }
> > > +
> > > +Done:
> > > + if ((Trb != NULL) && (Status == EFI_NOT_READY)) {
> > > + Packet = Trb->Packet;
> > > + if (Packet->Timeout == 0) {
> > > + InfiniteWait = TRUE;
> > > + } else {
> > > + InfiniteWait = FALSE;
> > > + }
> > > + if ((!InfiniteWait) && (Trb->Timeout-- == 0)) {
> > > + RemoveEntryList (Link);
> > > + Trb->Packet->TransactionStatus = EFI_TIMEOUT;
> > > + TrbEvent = Trb->Event;
> > > + DwMmcFreeTrb (Trb);
> > > + DEBUG ((
> > > + DEBUG_VERBOSE,
> > > + "ProcessAsyncTaskList(): Signal Event %p EFI_TIMEOUT\n",
> > > + TrbEvent
> > > + ));
> > > + gBS->SignalEvent (TrbEvent);
> > > + return;
> > > + }
> > > + }
> > > + if ((Trb != NULL) && (Status != EFI_NOT_READY)) {
> > > + RemoveEntryList (Link);
> > > + Trb->Packet->TransactionStatus = Status;
> > > + TrbEvent = Trb->Event;
> > > + DwMmcFreeTrb (Trb);
> > > + DEBUG ((
> > > + DEBUG_VERBOSE,
> > > + "ProcessAsyncTaskList(): Signal Event %p with %r\n",
> > > + TrbEvent,
> > > + Status
> > > + ));
> > > + gBS->SignalEvent (TrbEvent);
> > > + }
> > > + return;
> > > +}
> > > +
> > > +/**
> > > + Sd removable device enumeration callback function when the timer
> > event is signaled.
> > > +
> > > + @param[in] Event The Event this notify function registered to.
> > > + @param[in] Context Pointer to the context data registered to the
> > > + Event.
> > > +
> > > +**/
> > > +VOID
> > > +EFIAPI
> > > +DwMmcHcEnumerateDevice (
> > > + IN EFI_EVENT Event,
> > > + IN VOID* Context
> > > + )
> > > +{
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > + EFI_STATUS Status;
> > > + BOOLEAN MediaPresent;
> > > + UINT32 RoutineNum;
> > > + DWMMC_CARD_TYPE_DETECT_ROUTINE *Routine;
> > > + UINTN Index;
> > > + LIST_ENTRY *Link;
> > > + LIST_ENTRY *NextLink;
> > > + DW_MMC_HC_TRB *Trb;
> > > + EFI_TPL OldTpl;
> > > +
> > > + Private = (DW_MMC_HC_PRIVATE_DATA *)Context;
> > > +
> > > + if ((Private->Slot[0].Enable) &&
> > > + (Private->Slot[0].SlotType == RemovableSlot)) {
> > > + Status = DwMmcHcCardDetect (
> > > + Private->DevBase,
> > > + Private->ControllerHandle,
> > > + 0,
> > > + &MediaPresent
> > > + );
> > > + if ((Status == EFI_MEDIA_CHANGED) && !MediaPresent) {
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "DwMmcHcEnumerateDevice: device disconnected at %p\n",
> > > + Private->DevBase
> > > + ));
> > > + Private->Slot[0].MediaPresent = FALSE;
> > > + //
> > > + // Signal all async task events at the slot with EFI_NO_MEDIA status.
> > > + //
> > > + OldTpl = gBS->RaiseTPL (TPL_NOTIFY);
> > > + for (Link = GetFirstNode (&Private->Queue);
> > > + !IsNull (&Private->Queue, Link);
> > > + Link = NextLink) {
> > > + NextLink = GetNextNode (&Private->Queue, Link);
> > > + Trb = DW_MMC_HC_TRB_FROM_THIS (Link);
> > > + if (Trb->Slot == 0) {
> > > + RemoveEntryList (Link);
> > > + Trb->Packet->TransactionStatus = EFI_NO_MEDIA;
> > > + gBS->SignalEvent (Trb->Event);
> > > + DwMmcFreeTrb (Trb);
> > > + }
> > > + }
> > > + gBS->RestoreTPL (OldTpl);
> > > + //
> > > + // Notify the upper layer the connect state change through
> > > + // ReinstallProtocolInterface.
> > > + //
> > > + gBS->ReinstallProtocolInterface (
> > > + Private->ControllerHandle,
> > > + &gEfiSdMmcPassThruProtocolGuid,
> > > + &Private->PassThru,
> > > + &Private->PassThru
> > > + );
> > > + }
> > > + if ((Status == EFI_MEDIA_CHANGED) && MediaPresent) {
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "DwMmcHcEnumerateDevice: device connected at %p\n",
> > > + Private->DevBase
> > > + ));
> > > + //
> > > + // Initialize slot and start identification process for the new
> > > + // attached device
> > > + //
> > > + Status = DwMmcHcInitHost (Private->DevBase, Private-
> >Capability[0]);
> > > + if (EFI_ERROR (Status)) {
> > > + return;
> > > + }
> > > + //
> > > + // Reset the specified slot of the SD/MMC Pci Host Controller
> > > + //
> > > + Status = DwMmcHcReset (Private->DevBase, Private->Capability[0]);
> > > + if (EFI_ERROR (Status)) {
> > > + return;
> > > + }
> > > +
> > > + Private->Slot[0].MediaPresent = TRUE;
> > > + RoutineNum = sizeof (mCardTypeDetectRoutineTable) /
> > > + sizeof (DWMMC_CARD_TYPE_DETECT_ROUTINE);
> > > + for (Index = 0; Index < RoutineNum; Index++) {
> > > + Routine = &mCardTypeDetectRoutineTable[Index];
> > > + if (*Routine != NULL) {
> > > + Status = (*Routine) (Private);
> > > + if (!EFI_ERROR (Status)) {
> > > + break;
> > > + }
> > > + }
> > > + }
> > > + //
> > > + // This card doesn't get initialized correctly.
> > > + //
> > > + if (Index == RoutineNum) {
> > > + return;
> > > + }
> > > +
> > > + //
> > > + // Notify the upper layer the connect state change through
> > > + // ReinstallProtocolInterface.
> > > + //
> > > + gBS->ReinstallProtocolInterface (
> > > + Private->ControllerHandle,
> > > + &gEfiSdMmcPassThruProtocolGuid,
> > > + &Private->PassThru,
> > > + &Private->PassThru
> > > + );
> > > + }
> > > + }
> > > +
> > > + return;
> > > +}
> > > +
> > > +/**
> > > + Reset the specified SD/MMC host controller and enable all interrupts.
> > > +
> > > + @param[in] DevBase The Mmio Device Base Address.
> > > +
> > > + @retval EFI_SUCCESS The software reset executes successfully.
> > > + @retval Others The software reset fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcReset (
> > > + IN UINTN DevBase,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + UINT32 BlkSize;
> > > +
> > > + //
> > > + // Enable all interrupt after reset all.
> > > + //
> > > + Status = DwMmcHcEnableInterrupt (DevBase);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((DEBUG_ERROR, "DwMmcHcReset: enable interrupts fail:
> > %r\n", Status));
> > > + return Status;
> > > + }
> > > + Status = DwMmcHcInitTimeoutCtrl (DevBase);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + BlkSize = DW_MMC_BLOCK_SIZE;
> > > + MmioWrite32 (DevBase + DW_MMC_BLKSIZ, BlkSize);
> > > +
> > > + Status = DwMmcHcInitClockFreq (DevBase, Capability);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + Status = DwMmcHcSetBusWidth (DevBase, FALSE, 1);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Tests to see if this driver supports a given controller. If a child device
> > > + is provided, it further tests to see if this driver supports creating a
> > > + handle for the specified child device.
> > > +
> > > + This function checks to see if the driver specified by This supports the
> > > + device specified by ControllerHandle. Drivers will typically use the
> device
> > > + path attached to ControllerHandle and/or the services from the bus I/O
> > > + abstraction attached to ControllerHandle to determine if the driver
> > supports
> > > + ControllerHandle. This function may be called many times during
> > platform
> > > + initialization. In order to reduce boot times, the tests performed by this
> > > + function must be very small, and take as little time as possible to
> > execute.
> > > + This function must not change the state of any hardware devices, and
> > this
> > > + function must be aware that the device specified by ControllerHandle
> > may
> > > + already be managed by the same driver or a different driver. This
> > function
> > > + must match its calls to AllocatePages() with FreePages(), AllocatePool()
> > with
> > > + FreePool(), and OpenProtocol() with CloseProtocol(). Since
> > ControllerHandle
> > > + may have been previously started by the same driver, if a protocol is
> > already
> > > + in the opened state, then it must not be closed with CloseProtocol().
> This
> > is
> > > + required to guarantee the state of ControllerHandle is not modified by
> > this
> > > + function.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_DRIVER_BINDING_PROTOCOL
> > > + instance.
> > > + @param[in] ControllerHandle The handle of the controller to test.
> This
> > > + handle must support a protocol interface that
> > > + supplies an I/O abstraction to the driver.
> > > + @param[in] RemainingDevicePath A pointer to the remaining portion
> of
> > a
> > > + device path. This parameter is ignored by
> > > + device drivers, and is optional for bus
> > > + drivers. For bus drivers, if this parameter
> > > + is not NULL, then the bus driver must deter-
> > > + mine if the bus controller specified by
> > > + ControllerHandle and the child controller
> > > + specified by RemainingDevicePath are both
> > > + supported by this bus driver.
> > > +
> > > + @retval EFI_SUCCESS The device specified by ControllerHandle
> > and
> > > + RemainingDevicePath is supported by the
> > > + driver specified by This.
> > > + @retval EFI_ALREADY_STARTED The device specified by
> > ControllerHandle and
> > > + RemainingDevicePath is already being managed
> > > + by the driver specified by This.
> > > + @retval EFI_ACCESS_DENIED The device specified by
> > ControllerHandle and
> > > + RemainingDevicePath is already being managed
> > > + by a different driver or an application that
> > > + requires exclusive access.
> > > + Currently not implemented.
> > > + @retval EFI_UNSUPPORTED The device specified by
> > ControllerHandle and
> > > + RemainingDevicePath is not supported by the
> > > + driver specified by This.
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcDriverBindingSupported (
> > > + IN EFI_DRIVER_BINDING_PROTOCOL *This,
> > > + IN EFI_HANDLE Controller,
> > > + IN EFI_DEVICE_PATH_PROTOCOL *RemainingDevicePath
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + EFI_DEVICE_PATH_PROTOCOL *ParentDevicePath;
> > > + NON_DISCOVERABLE_DEVICE *Dev;
> > > + PLATFORM_DW_MMC_PROTOCOL *PlatformDwMmc;
> > > +
> > > + ParentDevicePath = NULL;
> > > +
> > > + Status = gBS->LocateProtocol (
> > > + &gPlatformDwMmcProtocolGuid,
> > > + NULL,
> > > + (VOID **) &PlatformDwMmc
> > > + );
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + Status = gBS->OpenProtocol (
> > > + Controller,
> > > + &gEfiDevicePathProtocolGuid,
> > > + (VOID *) &ParentDevicePath,
> > > + This->DriverBindingHandle,
> > > + Controller,
> > > + EFI_OPEN_PROTOCOL_BY_DRIVER
> > > + );
> > > + if (EFI_ERROR (Status)) {
> > > + //
> > > + // EFI_ALREADY_STARTED is also an error.
> > > + //
> > > + return Status;
> > > + }
> > > + //
> > > + // Close the protocol because we don't use it here.
> > > + //
> > > + gBS->CloseProtocol (
> > > + Controller,
> > > + &gEfiDevicePathProtocolGuid,
> > > + This->DriverBindingHandle,
> > > + Controller
> > > + );
> > > +
> > > + //
> > > + // Now test the EmbeddedNonDiscoverableIoProtocol.
> > > + //
> > > + Status = gBS->OpenProtocol (
> > > + Controller,
> > > + &gEdkiiNonDiscoverableDeviceProtocolGuid,
> > > + (VOID **) &Dev,
> > > + This->DriverBindingHandle,
> > > + Controller,
> > > + EFI_OPEN_PROTOCOL_BY_DRIVER
> > > + );
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + gBS->CloseProtocol (
> > > + Controller,
> > > + &gEdkiiNonDiscoverableDeviceProtocolGuid,
> > > + This->DriverBindingHandle,
> > > + Controller
> > > + );
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Starts a device controller or a bus controller.
> > > +
> > > + The Start() function is designed to be invoked from the EFI boot service
> > > + ConnectController().
> > > + As a result, much of the error checking on the parameters to Start() has
> > > + been moved into this
> > > + common boot service. It is legal to call Start() from other locations,
> > > + but the following calling restrictions must be followed or the system
> > > + behavior will not be deterministic.
> > > + 1. ControllerHandle must be a valid EFI_HANDLE.
> > > + 2. If RemainingDevicePath is not NULL, then it must be a pointer to a
> > > + naturally aligned EFI_DEVICE_PATH_PROTOCOL.
> > > + 3. Prior to calling Start(), the Supported() function for the driver
> > > + specified by This must have been called with the same calling
> > parameters,
> > > + and Supported() must have returned EFI_SUCCESS.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_DRIVER_BINDING_PROTOCOL
> > > + instance.
> > > + @param[in] ControllerHandle The handle of the controller to start.
> > This
> > > + handle must support a protocol interface
> > > + that supplies an I/O abstraction to the
> > > + driver.
> > > + @param[in] RemainingDevicePath A pointer to the remaining portion
> of
> > a
> > > + device path. This parameter is ignored by
> > > + device drivers, and is optional for bus
> > > + drivers.
> > > + For a bus driver, if this parameter is NULL,
> > > + then handles for all the children of
> > > + Controller are created by this driver.
> > > + If this parameter is not NULL and the first
> > > + Device Path Node is not the End of Device
> > > + Path Node, then only the handle for the
> > > + child device specified by the first Device
> > > + Path Node of RemainingDevicePath is created
> > > + by this driver.
> > > + If the first Device Path Node of
> > > + RemainingDevicePath is the End of Device Path
> > > + Node, no child handle is created by this
> > > + driver.
> > > +
> > > + @retval EFI_SUCCESS The device was started.
> > > + @retval EFI_DEVICE_ERROR The device could not be started due to
> a
> > > + device error. Currently not implemented.
> > > + @retval EFI_OUT_OF_RESOURCES The request could not be
> > completed due to a
> > > + lack of resources.
> > > + @retval Others The driver failded to start the device.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcDriverBindingStart (
> > > + IN EFI_DRIVER_BINDING_PROTOCOL *This,
> > > + IN EFI_HANDLE Controller,
> > > + IN EFI_DEVICE_PATH_PROTOCOL *RemainingDevicePath
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > +
> > > + NON_DISCOVERABLE_DEVICE *Dev;
> > > +
> > > + BOOLEAN MediaPresent;
> > > + DWMMC_CARD_TYPE_DETECT_ROUTINE *Routine;
> > > + UINT8 Index;
> > > + UINT32 RoutineNum;
> > > + PLATFORM_DW_MMC_PROTOCOL *PlatformDwMmc;
> > > +
> > > + Status = gBS->LocateProtocol (
> > > + &gPlatformDwMmcProtocolGuid,
> > > + NULL,
> > > + (VOID **) &PlatformDwMmc
> > > + );
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((DEBUG_ERROR, "err %d", __LINE__));
> > > + return Status;
> > > + }
> > > +
> > > + Status = gBS->OpenProtocol (
> > > + Controller,
> > > + &gEdkiiNonDiscoverableDeviceProtocolGuid,
> > > + (VOID **) &Dev,
> > > + This->DriverBindingHandle,
> > > + Controller,
> > > + EFI_OPEN_PROTOCOL_BY_DRIVER
> > > + );
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((DEBUG_ERROR, "err %d", __LINE__));
> > > + return Status;
> > > + }
> > > +
> > > + Private = AllocateCopyPool (sizeof (DW_MMC_HC_PRIVATE_DATA),
> > &gDwMmcHcTemplate);
> > > + if (Private == NULL) {
> > > + DEBUG ((DEBUG_ERROR, "err %d", __LINE__));
> > > + Status = EFI_OUT_OF_RESOURCES;
> > > + goto Done;
> > > + }
> > > +
> > > + Private->ControllerHandle = Controller;
> > > + Private->DevBase = Dev->Resources[0].AddrRangeMin;
> > > + Private->PlatformDwMmc = PlatformDwMmc;
> > > + InitializeListHead (&Private->Queue);
> > > +
> > > + Status = Private->PlatformDwMmc->GetCapability (Controller, 0,
> > &Private->Capability[0]);
> > > +
> > > + if (EFI_ERROR (Status)) {
> > > + goto Done;
> > > + }
> > > +
> > > + if (Private->Capability[0].BaseClkFreq == 0) {
> > > + goto Done;
> > > + }
> > > +
> > > + DumpCapabilityReg (0, &Private->Capability[0]);
> > > +
> > > + MediaPresent = FALSE;
> > > +
> > > + Status = Private->PlatformDwMmc->CardDetect (Controller, 0);
> > > + Status = DwMmcHcCardDetect (Private->DevBase, Controller, 0,
> > &MediaPresent);
> > > + if (MediaPresent == FALSE) {
> > > + goto Done;
> > > + }
> > > +
> > > + //
> > > + // Initialize slot and start identification process for the new attached
> > device
> > > + //
> > > + Status = DwMmcHcInitHost (Private->DevBase, Private->Capability[0]);
> > > + if (EFI_ERROR (Status)) {
> > > + goto Done;
> > > + }
> > > +
> > > + //
> > > + // Reset HC
> > > + //
> > > + Status = DwMmcHcReset (Private->DevBase, Private->Capability[0]);
> > > + if (EFI_ERROR (Status)) {
> > > + goto Done;
> > > + }
> > > +
> > > + Private->Slot[0].CardType = Private->Capability[0].CardType;
> > > + Private->Slot[0].Enable = TRUE;
> > > + Private->Slot[0].MediaPresent = TRUE;
> > > +
> > > + RoutineNum = sizeof (mCardTypeDetectRoutineTable) / sizeof
> > (DWMMC_CARD_TYPE_DETECT_ROUTINE);
> > > + for (Index = 0; Index < RoutineNum; Index++) {
> > > + Routine = &mCardTypeDetectRoutineTable[Index];
> > > + if (*Routine != NULL) {
> > > + Status = (*Routine) (Private);
> > > + if (!EFI_ERROR (Status)) {
> > > + break;
> > > + }
> > > + }
> > > + }
> > > +
> > > + //
> > > + // Start the asynchronous I/O monitor
> > > + //
> > > + Status = gBS->CreateEvent (
> > > + EVT_TIMER | EVT_NOTIFY_SIGNAL,
> > > + TPL_NOTIFY,
> > > + ProcessAsyncTaskList,
> > > + Private,
> > > + &Private->TimerEvent
> > > + );
> > > + if (EFI_ERROR (Status)) {
> > > + goto Done;
> > > + }
> > > +
> > > + Status = gBS->SetTimer (Private->TimerEvent, TimerPeriodic,
> > DW_MMC_HC_ASYNC_TIMER);
> > > + if (EFI_ERROR (Status)) {
> > > + goto Done;
> > > + }
> > > +
> > > + //
> > > + // Start the Sd removable device connection enumeration
> > > + //
> > > + Status = gBS->CreateEvent (
> > > + EVT_TIMER | EVT_NOTIFY_SIGNAL,
> > > + TPL_CALLBACK,
> > > + DwMmcHcEnumerateDevice,
> > > + Private,
> > > + &Private->ConnectEvent
> > > + );
> > > + if (EFI_ERROR (Status)) {
> > > + goto Done;
> > > + }
> > > +
> > > + Status = gBS->SetTimer (Private->ConnectEvent, TimerPeriodic,
> > DW_MMC_HC_ENUM_TIMER);
> > > + if (EFI_ERROR (Status)) {
> > > + goto Done;
> > > + }
> > > +
> > > + Status = gBS->InstallMultipleProtocolInterfaces (
> > > + &Controller,
> > > + &gEfiSdMmcPassThruProtocolGuid,
> > > + &(Private->PassThru),
> > > + NULL
> > > + );
> > > +
> > > + DEBUG ((DEBUG_INFO, "DwMmcHcDriverBindingStart: %r End on
> %x\n",
> > Status, Controller));
> > > +
> > > +Done:
> > > + if (EFI_ERROR (Status)) {
> > > + if ((Private != NULL) && (Private->TimerEvent != NULL)) {
> > > + gBS->CloseEvent (Private->TimerEvent);
> > > + }
> > > +
> > > + if ((Private != NULL) && (Private->ConnectEvent != NULL)) {
> > > + gBS->CloseEvent (Private->ConnectEvent);
> > > + }
> > > +
> > > + if (Private != NULL) {
> > > + FreePool (Private);
> > > + }
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Stops a device controller or a bus controller.
> > > +
> > > + The Stop() function is designed to be invoked from the EFI boot service
> > > + DisconnectController().
> > > + As a result, much of the error checking on the parameters to Stop() has
> > been
> > > + moved into this common boot service. It is legal to call Stop() from
> other
> > > + locations, but the following calling restrictions must be followed or the
> > > + system behavior will not be deterministic.
> > > + 1. ControllerHandle must be a valid EFI_HANDLE that was used on a
> > previous
> > > + call to this same driver's Start() function.
> > > + 2. The first NumberOfChildren handles of ChildHandleBuffer must all
> be a
> > valid
> > > + EFI_HANDLE. In addition, all of these handles must have been created
> > in
> > > + this driver's Start() function, and the Start() function must have called
> > > + OpenProtocol() on ControllerHandle with an Attribute of
> > > + EFI_OPEN_PROTOCOL_BY_CHILD_CONTROLLER.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_DRIVER_BINDING_PROTOCOL
> > > + instance.
> > > + @param[in] ControllerHandle A handle to the device being stopped.
> > The handle
> > > + must support a bus specific I/O protocol for the
> > > + driver to use to stop the device.
> > > + @param[in] NumberOfChildren The number of child device handles in
> > > + ChildHandleBuffer.
> > > + @param[in] ChildHandleBuffer An array of child handles to be freed.
> > May be
> > > + NULL if NumberOfChildren is 0.
> > > +
> > > + @retval EFI_SUCCESS The device was stopped.
> > > + @retval EFI_DEVICE_ERROR The device could not be stopped due to
> a
> > device
> > > + error.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcHcDriverBindingStop (
> > > + IN EFI_DRIVER_BINDING_PROTOCOL *This,
> > > + IN EFI_HANDLE Controller,
> > > + IN UINTN NumberOfChildren,
> > > + IN EFI_HANDLE *ChildHandleBuffer
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru;
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > + LIST_ENTRY *Link;
> > > + LIST_ENTRY *NextLink;
> > > + DW_MMC_HC_TRB *Trb;
> > > +
> > > + DEBUG ((DEBUG_INFO, "DwMmcHcDriverBindingStop: Start\n"));
> > > +
> > > + Status = gBS->OpenProtocol (
> > > + Controller,
> > > + &gEfiSdMmcPassThruProtocolGuid,
> > > + (VOID**) &PassThru,
> > > + This->DriverBindingHandle,
> > > + Controller,
> > > + EFI_OPEN_PROTOCOL_GET_PROTOCOL
> > > + );
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + Private = DW_MMC_HC_PRIVATE_FROM_THIS (PassThru);
> > > + //
> > > + // Close Non-Blocking timer and free Task list.
> > > + //
> > > + if (Private->TimerEvent != NULL) {
> > > + gBS->CloseEvent (Private->TimerEvent);
> > > + Private->TimerEvent = NULL;
> > > + }
> > > + if (Private->ConnectEvent != NULL) {
> > > + gBS->CloseEvent (Private->ConnectEvent);
> > > + Private->ConnectEvent = NULL;
> > > + }
> > > + //
> > > + // As the timer is closed, there is no needs to use TPL lock to
> > > + // protect the critical region "queue".
> > > + //
> > > + for (Link = GetFirstNode (&Private->Queue);
> > > + !IsNull (&Private->Queue, Link);
> > > + Link = NextLink) {
> > > + NextLink = GetNextNode (&Private->Queue, Link);
> > > + RemoveEntryList (Link);
> > > + Trb = DW_MMC_HC_TRB_FROM_THIS (Link);
> > > + Trb->Packet->TransactionStatus = EFI_ABORTED;
> > > + gBS->SignalEvent (Trb->Event);
> > > + DwMmcFreeTrb (Trb);
> > > + }
> > > +
> > > + //
> > > + // Uninstall Block I/O protocol from the device handle
> > > + //
> > > + Status = gBS->UninstallProtocolInterface (
> > > + Controller,
> > > + &gEfiSdMmcPassThruProtocolGuid,
> > > + &(Private->PassThru)
> > > + );
> > > +
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + gBS->CloseProtocol (
> > > + Controller,
> > > + &gEfiPciIoProtocolGuid,
> > > + This->DriverBindingHandle,
> > > + Controller
> > > + );
> > > +
> > > + FreePool (Private);
> > > +
> > > + DEBUG ((DEBUG_INFO, "DwMmcHcDriverBindingStop: End with %r\n",
> > Status));
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Sends SD command to an SD card that is attached to the SD controller.
> > > +
> > > + The PassThru() function sends the SD command specified by Packet to
> > the SD
> > > + card specified by Slot.
> > > +
> > > + If Packet is successfully sent to the SD card, then EFI_SUCCESS is
> > returned.
> > > +
> > > + If a device error occurs while sending the Packet, then
> > EFI_DEVICE_ERROR is
> > > + returned.
> > > +
> > > + If Slot is not in a valid range for the SD controller, then
> > > + EFI_INVALID_PARAMETER is returned.
> > > +
> > > + If Packet defines a data command but both InDataBuffer and
> > OutDataBuffer are
> > > + NULL, EFI_INVALID_PARAMETER is returned.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > > + command to.
> > > + @param[in,out] Packet A pointer to the SD command data
> structure.
> > > + @param[in] Event If Event is NULL, blocking I/O is performed. If
> > > + Event is not NULL, then nonblocking I/O is
> > > + performed, and Event will be signaled when the
> > > + Packet completes.
> > > +
> > > + @retval EFI_SUCCESS The SD Command Packet was sent by the
> > host.
> > > + @retval EFI_DEVICE_ERROR A device error occurred while
> attempting
> > to send
> > > + the SD command Packet.
> > > + @retval EFI_INVALID_PARAMETER Packet, Slot, or the contents of the
> > Packet is
> > > + invalid.
> > > + @retval EFI_INVALID_PARAMETER Packet defines a data command but
> > both
> > > + InDataBuffer and OutDataBuffer are NULL.
> > > + @retval EFI_NO_MEDIA SD Device not present in the Slot.
> > > + @retval EFI_UNSUPPORTED The command described by the SD
> > Command Packet
> > > + is not supported by the host controller.
> > > + @retval EFI_BAD_BUFFER_SIZE The InTransferLength or
> > OutTransferLength
> > > + exceeds the limit supported by SD card
> > > + ( i.e. if the number of bytes exceed the Last
> > > + LBA).
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcPassThruPassThru (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *This,
> > > + IN UINT8 Slot,
> > > + IN OUT EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet,
> > > + IN EFI_EVENT Event OPTIONAL
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > + DW_MMC_HC_TRB *Trb;
> > > + EFI_TPL OldTpl;
> > > +
> > > + if ((This == NULL) || (Packet == NULL)) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + if ((Packet->SdMmcCmdBlk == NULL) || (Packet->SdMmcStatusBlk ==
> > NULL)) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + if ((Packet->OutDataBuffer == NULL) && (Packet->OutTransferLength
> !=
> > 0)) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + if ((Packet->InDataBuffer == NULL) && (Packet->InTransferLength !=
> 0))
> > {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + Private = DW_MMC_HC_PRIVATE_FROM_THIS (This);
> > > +
> > > + if (!Private->Slot[Slot].Enable) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + if (!Private->Slot[Slot].MediaPresent) {
> > > + return EFI_NO_MEDIA;
> > > + }
> > > +
> > > + Trb = DwMmcCreateTrb (Private, Slot, Packet, Event);
> > > + if (Trb == NULL) {
> > > + return EFI_OUT_OF_RESOURCES;
> > > + }
> > > + //
> > > + // Immediately return for async I/O.
> > > + //
> > > + if (Event != NULL) {
> > > + return EFI_SUCCESS;
> > > + }
> > > +
> > > + //
> > > + // Wait async I/O list is empty before execute sync I/O operation.
> > > + //
> > > + while (TRUE) {
> > > + OldTpl = gBS->RaiseTPL (TPL_NOTIFY);
> > > + if (IsListEmpty (&Private->Queue)) {
> > > + gBS->RestoreTPL (OldTpl);
> > > + break;
> > > + }
> > > + gBS->RestoreTPL (OldTpl);
> > > + }
> > > +
> > > + Status = DwMmcWaitTrbEnv (Private, Trb);
> > > + if (EFI_ERROR (Status)) {
> > > + goto Done;
> > > + }
> > > +
> > > + Status = DwMmcExecTrb (Private, Trb);
> > > + if (EFI_ERROR (Status)) {
> > > + goto Done;
> > > + }
> > > +
> > > + Status = DwMmcWaitTrbResult (Private, Trb);
> > > + if (EFI_ERROR (Status)) {
> > > + goto Done;
> > > + }
> > > +
> > > +Done:
> > > + if (Trb != NULL) {
> > > + DwMmcFreeTrb (Trb);
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Used to retrieve next slot numbers supported by the SD controller. The
> > > + function returns information about all available slots (populated or
> > > + not-populated).
> > > +
> > > + The GetNextSlot() function retrieves the next slot number on an SD
> > controller.
> > > + If on input Slot is 0xFF, then the slot number of the first slot on the SD
> > > + controller is returned.
> > > +
> > > + If Slot is a slot number that was returned on a previous call to
> > > + GetNextSlot(), then the slot number of the next slot on the SD
> controller
> > is
> > > + returned.
> > > +
> > > + If Slot is not 0xFF and Slot was not returned on a previous call to
> > > + GetNextSlot(), EFI_INVALID_PARAMETER is returned.
> > > +
> > > + If Slot is the slot number of the last slot on the SD controller, then
> > > + EFI_NOT_FOUND is returned.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_SD_MMMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in,out] Slot On input, a pointer to a slot number on the
> SD
> > > + controller.
> > > + On output, a pointer to the next slot number on
> > > + the SD controller.
> > > + An input value of 0xFF retrieves the first slot
> > > + number on the SD controller.
> > > +
> > > + @retval EFI_SUCCESS The next slot number on the SD controller
> > was
> > > + returned in Slot.
> > > + @retval EFI_NOT_FOUND There are no more slots on this SD
> > controller.
> > > + @retval EFI_INVALID_PARAMETER Slot is not 0xFF and Slot was not
> > returned on a
> > > + previous call to GetNextSlot().
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcPassThruGetNextSlot (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *This,
> > > + IN OUT UINT8 *Slot
> > > + )
> > > +{
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > +
> > > + if ((This == NULL) || (Slot == NULL)) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + Private = DW_MMC_HC_PRIVATE_FROM_THIS (This);
> > > +
> > > + if (*Slot == 0xFF) {
> > > + if (Private->Slot[0].Enable) {
> > > + *Slot = 0;
> > > + Private->PreviousSlot = 0;
> > > + return EFI_SUCCESS;
> > > + }
> > > + return EFI_NOT_FOUND;
> > > + } else if (*Slot == Private->PreviousSlot) {
> > > + return EFI_NOT_FOUND;
> > > + } else {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +}
> > > +
> > > +/**
> > > + Used to allocate and build a device path node for an SD card on the SD
> > > + controller.
> > > +
> > > + The BuildDevicePath() function allocates and builds a single device
> node
> > > + for the SD card specified by Slot.
> > > +
> > > + If the SD card specified by Slot is not present on the SD controller, then
> > > + EFI_NOT_FOUND is returned.
> > > +
> > > + If DevicePath is NULL, then EFI_INVALID_PARAMETER is returned.
> > > +
> > > + If there are not enough resources to allocate the device path node,
> then
> > > + EFI_OUT_OF_RESOURCES is returned.
> > > +
> > > + Otherwise, DevicePath is allocated with the boot service
> AllocatePool(),
> > > + the contents of DevicePath are initialized to describe the SD card
> > specified
> > > + by Slot, and EFI_SUCCESS is returned.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_SD_MMMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Slot Specifies the slot number of the SD card for
> > > + which a device path node is to be allocated and
> > > + built.
> > > + @param[in,out] DevicePath A pointer to a single device path node
> that
> > > + describes the SD card specified by Slot. This
> > > + function is responsible for allocating the
> > > + buffer DevicePath with the boot service
> > > + AllocatePool(). It is the caller's responsi-
> > > + bility to free DevicePath when the caller is
> > > + finished with DevicePath.
> > > +
> > > + @retval EFI_SUCCESS The device path node that describes the SD
> > card
> > > + specified by Slot was allocated and returned in
> > > + DevicePath.
> > > + @retval EFI_NOT_FOUND The SD card specified by Slot does not
> > exist on
> > > + the SD controller.
> > > + @retval EFI_INVALID_PARAMETER DevicePath is NULL.
> > > + @retval EFI_OUT_OF_RESOURCES There are not enough resources to
> > allocate
> > > + DevicePath.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcPassThruBuildDevicePath (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *This,
> > > + IN UINT8 Slot,
> > > + IN OUT EFI_DEVICE_PATH_PROTOCOL **DevicePath
> > > + )
> > > +{
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > + SD_DEVICE_PATH *SdNode;
> > > + EMMC_DEVICE_PATH *EmmcNode;
> > > +
> > > + if ((This == NULL) || (DevicePath == NULL) || (Slot >=
> > DW_MMC_HC_MAX_SLOT)) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + Private = DW_MMC_HC_PRIVATE_FROM_THIS (This);
> > > +
> > > + if ((!Private->Slot[Slot].Enable) || (!Private->Slot[Slot].MediaPresent))
> {
> > > + return EFI_NOT_FOUND;
> > > + }
> > > +
> > > + if (Private->Slot[Slot].CardType == SdCardType) {
> > > + SdNode = AllocateCopyPool (sizeof (SD_DEVICE_PATH),
> > &mSdDpTemplate);
> > > + if (SdNode == NULL) {
> > > + return EFI_OUT_OF_RESOURCES;
> > > + }
> > > + SdNode->SlotNumber = Slot;
> > > +
> > > + *DevicePath = (EFI_DEVICE_PATH_PROTOCOL *) SdNode;
> > > + } else if (Private->Slot[Slot].CardType == EmmcCardType) {
> > > + EmmcNode = AllocateCopyPool (sizeof (EMMC_DEVICE_PATH),
> > &mEmmcDpTemplate);
> > > + if (EmmcNode == NULL) {
> > > + return EFI_OUT_OF_RESOURCES;
> > > + }
> > > + EmmcNode->SlotNumber = Slot;
> > > +
> > > + *DevicePath = (EFI_DEVICE_PATH_PROTOCOL *) EmmcNode;
> > > + } else {
> > > + //
> > > + // Currently we only support SD and EMMC two device nodes.
> > > + //
> > > + return EFI_NOT_FOUND;
> > > + }
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + This function retrieves an SD card slot number based on the input
> device
> > path.
> > > +
> > > + The GetSlotNumber() function retrieves slot number for the SD card
> > specified
> > > + by the DevicePath node. If DevicePath is NULL,
> > EFI_INVALID_PARAMETER is
> > > + returned.
> > > +
> > > + If DevicePath is not a device path node type that the SD Pass Thru
> driver
> > > + supports, EFI_UNSUPPORTED is returned.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] DevicePath A pointer to the device path node that
> > describes
> > > + a SD card on the SD controller.
> > > + @param[out] Slot On return, points to the slot number of an SD
> > > + card on the SD controller.
> > > +
> > > + @retval EFI_SUCCESS SD card slot number is returned in Slot.
> > > + @retval EFI_INVALID_PARAMETER Slot or DevicePath is NULL.
> > > + @retval EFI_UNSUPPORTED DevicePath is not a device path node
> > type that
> > > + the SD Pass Thru driver supports.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcPassThruGetSlotNumber (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *This,
> > > + IN EFI_DEVICE_PATH_PROTOCOL *DevicePath,
> > > + OUT UINT8 *Slot
> > > + )
> > > +{
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > + SD_DEVICE_PATH *SdNode;
> > > + EMMC_DEVICE_PATH *EmmcNode;
> > > + UINT8 SlotNumber;
> > > +
> > > + if ((This == NULL) || (DevicePath == NULL) || (Slot == NULL)) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + Private = DW_MMC_HC_PRIVATE_FROM_THIS (This);
> > > +
> > > + //
> > > + // Check whether the DevicePath belongs to SD_DEVICE_PATH or
> > EMMC_DEVICE_PATH
> > > + //
> > > + if ((DevicePath->Type != MESSAGING_DEVICE_PATH) ||
> > > + ((DevicePath->SubType != MSG_SD_DP) &&
> > > + (DevicePath->SubType != MSG_EMMC_DP)) ||
> > > + (DevicePathNodeLength(DevicePath) != sizeof(SD_DEVICE_PATH))
> ||
> > > + (DevicePathNodeLength(DevicePath) !=
> > sizeof(EMMC_DEVICE_PATH))) {
> > > + return EFI_UNSUPPORTED;
> > > + }
> > > +
> > > + if (DevicePath->SubType == MSG_SD_DP) {
> > > + SdNode = (SD_DEVICE_PATH *) DevicePath;
> > > + SlotNumber = SdNode->SlotNumber;
> > > + } else {
> > > + EmmcNode = (EMMC_DEVICE_PATH *) DevicePath;
> > > + SlotNumber = EmmcNode->SlotNumber;
> > > + }
> > > +
> > > + if (SlotNumber >= DW_MMC_HC_MAX_SLOT) {
> > > + return EFI_NOT_FOUND;
> > > + }
> > > +
> > > + if (Private->Slot[SlotNumber].Enable) {
> > > + *Slot = SlotNumber;
> > > + return EFI_SUCCESS;
> > > + } else {
> > > + return EFI_NOT_FOUND;
> > > + }
> > > +}
> > > +
> > > +/**
> > > + Resets an SD card that is connected to the SD controller.
> > > +
> > > + The ResetDevice() function resets the SD card specified by Slot.
> > > +
> > > + If this SD controller does not support a device reset operation,
> > > + EFI_UNSUPPORTED is returned.
> > > +
> > > + If Slot is not in a valid slot number for this SD controller,
> > > + EFI_INVALID_PARAMETER is returned.
> > > +
> > > + If the device reset operation is completed, EFI_SUCCESS is returned.
> > > +
> > > + @param[in] This A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Slot Specifies the slot number of the SD card to be
> > > + reset.
> > > +
> > > + @retval EFI_SUCCESS The SD card specified by Slot was reset.
> > > + @retval EFI_UNSUPPORTED The SD controller does not support a
> > device
> > > + reset operation.
> > > + @retval EFI_INVALID_PARAMETER Slot number is invalid.
> > > + @retval EFI_NO_MEDIA SD Device not present in the Slot.
> > > + @retval EFI_DEVICE_ERROR The reset command failed due to a
> device
> > error
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EFIAPI
> > > +DwMmcPassThruResetDevice (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *This,
> > > + IN UINT8 Slot
> > > + )
> > > +{
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > + LIST_ENTRY *Link;
> > > + LIST_ENTRY *NextLink;
> > > + DW_MMC_HC_TRB *Trb;
> > > + EFI_TPL OldTpl;
> > > +
> > > + if (This == NULL) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + Private = DW_MMC_HC_PRIVATE_FROM_THIS (This);
> > > +
> > > + if (!Private->Slot[Slot].Enable) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + if (!Private->Slot[Slot].MediaPresent) {
> > > + return EFI_NO_MEDIA;
> > > + }
> > > +
> > > + //
> > > + // Free all async I/O requests in the queue
> > > + //
> > > + OldTpl = gBS->RaiseTPL (TPL_NOTIFY);
> > > +
> > > + for (Link = GetFirstNode (&Private->Queue);
> > > + !IsNull (&Private->Queue, Link);
> > > + Link = NextLink) {
> > > + NextLink = GetNextNode (&Private->Queue, Link);
> > > + RemoveEntryList (Link);
> > > + Trb = DW_MMC_HC_TRB_FROM_THIS (Link);
> > > + Trb->Packet->TransactionStatus = EFI_ABORTED;
> > > + gBS->SignalEvent (Trb->Event);
> > > + DwMmcFreeTrb (Trb);
> > > + }
> > > +
> > > + gBS->RestoreTPL (OldTpl);
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > diff --git a/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHci.c
> > b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHci.c
> > > new file mode 100644
> > > index 000000000000..b091f9803b2e
> > > --- /dev/null
> > > +++ b/EmbeddedPkg/Drivers/DwMmcHcDxe/DwMmcHci.c
> > > @@ -0,0 +1,1602 @@
> > > +/** @file
> > > + This driver is used to manage Designware SD/MMC PCI host
> controllers.
> > > +
> > > + It would expose EFI_SD_MMC_PASS_THRU_PROTOCOL for upper
> layer
> > use.
> > > +
> > > + Copyright (c) 2015 - 2020, Intel Corporation. All rights reserved.<BR>
> > > + Copyright (c) 2018, Linaro Ltd. All rights reserved.<BR>
> > > +
> > > + This program and the accompanying materials are licensed and made
> > available
> > > + under the terms and conditions of the BSD License which accompanies
> > this
> > > + distribution. The full text of the license may be found at
> > > + http://opensource.org/licenses/bsd-license.php
> > > +
> > > + THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS"
> > BASIS,
> > > + WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER
> > EXPRESS OR IMPLIED.
> > > +
> > > +**/
> > > +
> > > +#include <IndustryStandard/Emmc.h>
> > > +#include <IndustryStandard/Sd.h>
> > > +
> > > +#include <Library/ArmLib.h>
> > > +#include <Library/BaseMemoryLib.h>
> > > +#include <Library/DmaLib.h>
> > > +#include <Library/IoLib.h>
> > > +#include <Library/DebugLib.h>
> > > +#include <Library/MemoryAllocationLib.h>
> > > +#include <Library/UefiBootServicesTableLib.h>
> > > +
> > > +#include "DwMmcHcDxe.h"
> > > +
> > > +/**
> > > + Dump the content of SD/MMC host controller's Capability Register.
> > > +
> > > + @param[in] Slot The slot number of the SD card to send the
> > > + command to.
> > > + @param[in] Capability The buffer to store the capability data.
> > > +
> > > +**/
> > > +VOID
> > > +DumpCapabilityReg (
> > > + IN UINT8 Slot,
> > > + IN DW_MMC_HC_SLOT_CAP *Capability
> > > + )
> > > +{
> > > + //
> > > + // Dump Capability Data
> > > + //
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + " == Slot [%d] Capability is 0x%x ==\n",
> > > + Slot,
> > > + Capability
> > > + ));
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + " Base Clk Freq %dKHz\n",
> > > + Capability->BaseClkFreq
> > > + ));
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + " BusWidth %d\n",
> > > + Capability->BusWidth
> > > + ));
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + " HighSpeed Support %a\n",
> > > + Capability->HighSpeed ? "TRUE" : "FALSE"
> > > + ));
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + " Voltage 1.8 %a\n",
> > > + Capability->Voltage18 ? "TRUE" : "FALSE"
> > > + ));
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + " 64-bit Sys Bus %a\n",
> > > + Capability->SysBus64 ? "TRUE" : "FALSE"
> > > + ));
> > > + DEBUG ((DEBUG_INFO, " SlotType "));
> > > + if (Capability->SlotType == 0x00) {
> > > + DEBUG ((DEBUG_INFO, "%a\n", "Removable Slot"));
> > > + } else if (Capability->SlotType == 0x01) {
> > > + DEBUG ((DEBUG_INFO, "%a\n", "Embedded Slot"));
> > > + } else if (Capability->SlotType == 0x02) {
> > > + DEBUG ((DEBUG_INFO, "%a\n", "Shared Bus Slot"));
> > > + } else {
> > > + DEBUG ((DEBUG_INFO, "%a\n", "Reserved"));
> > > + }
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + " SDR50 Support %a\n",
> > > + Capability->Sdr50 ? "TRUE" : "FALSE"
> > > + ));
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + " SDR104 Support %a\n",
> > > + Capability->Sdr104 ? "TRUE" : "FALSE"
> > > + ));
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + " DDR50 Support %a\n",
> > > + Capability->Ddr50 ? "TRUE" : "FALSE"
> > > + ));
> > > + return;
> > > +}
> > > +
> > > +/**
> > > + Set all interrupt status bits in Normal and Error Interrupt Status Enable
> > > + register.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > +
> > > + @retval EFI_SUCCESS The operation executes successfully.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcEnableInterrupt (
> > > + UINTN DevBase
> > > + )
> > > +{
> > > + UINT32 IntStatus;
> > > + UINT32 IdIntEn;
> > > + UINT32 IdSts;
> > > +
> > > + //
> > > + // Enable all bits in Interrupt Mask Register
> > > + //
> > > + IntStatus = 0;
> > > + MmioWrite32 (DevBase + DW_MMC_INTMASK, IntStatus);
> > > +
> > > + //
> > > + // Clear status in Interrupt Status Register
> > > + //
> > > + IntStatus = ~0;
> > > + MmioWrite32 (DevBase + DW_MMC_RINTSTS, IntStatus);
> > > +
> > > + IdIntEn = ~0;
> > > + MmioWrite32 (DevBase + DW_MMC_IDINTEN, IdIntEn);
> > > +
> > > + IdSts = ~0;
> > > + MmioWrite32 (DevBase + DW_MMC_IDSTS, IdSts);
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +EFI_STATUS
> > > +DwMmcHcGetCapability (
> > > + IN UINTN DevBase,
> > > + IN EFI_HANDLE Controller,
> > > + IN UINT8 Slot,
> > > + OUT DW_MMC_HC_SLOT_CAP *Capacity
> > > + )
> > > +{
> > > + PLATFORM_DW_MMC_PROTOCOL *PlatformDwMmc;
> > > + EFI_STATUS Status;
> > > +
> > > + if (Capacity == NULL) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > + Status = gBS->LocateProtocol (
> > > + &gPlatformDwMmcProtocolGuid,
> > > + NULL,
> > > + (VOID **) &PlatformDwMmc
> > > + );
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + Status = PlatformDwMmc->GetCapability (Controller, Slot, Capacity);
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Detect whether there is a SD/MMC card attached at the specified
> > SD/MMC host
> > > + controller slot.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.1 for details.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command
> > > + to.
> > > + @param[out] MediaPresent The pointer to the media present
> boolean
> > value.
> > > +
> > > + @retval EFI_SUCCESS There is no media change happened.
> > > + @retval EFI_MEDIA_CHANGED There is media change happened.
> > > + @retval Others The detection fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcCardDetect (
> > > + IN UINTN DevBase,
> > > + IN EFI_HANDLE Controller,
> > > + IN UINT8 Slot,
> > > + OUT BOOLEAN *MediaPresent
> > > + )
> > > +{
> > > + PLATFORM_DW_MMC_PROTOCOL *PlatformDwMmc;
> > > + EFI_STATUS Status;
> > > +
> > > + if (MediaPresent == NULL) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > + Status = gBS->LocateProtocol (
> > > + &gPlatformDwMmcProtocolGuid,
> > > + NULL,
> > > + (VOID **) &PlatformDwMmc
> > > + );
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + *MediaPresent = PlatformDwMmc->CardDetect (Controller, Slot);
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +STATIC
> > > +EFI_STATUS
> > > +DwMmcHcUpdateClock (
> > > + IN UINTN DevBase
> > > + )
> > > +{
> > > + UINT32 Cmd;
> > > + UINT32 IntStatus;
> > > +
> > > + Cmd = BIT_CMD_WAIT_PRVDATA_COMPLETE |
> > BIT_CMD_UPDATE_CLOCK_ONLY |
> > > + BIT_CMD_START;
> > > + MmioWrite32 (DevBase + DW_MMC_CMD, Cmd);
> > > +
> > > + while (1) {
> > > + Cmd = MmioRead32 (DevBase + DW_MMC_CMD);
> > > +
> > > + if (!(Cmd & CMD_START_BIT)) {
> > > + break;
> > > + }
> > > +
> > > + IntStatus = MmioRead32 (DevBase + DW_MMC_RINTSTS);
> > > +
> > > + if (IntStatus & DW_MMC_INT_HLE) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "DwMmcHcUpdateClock: failed to update mmc clock frequency\n"
> > > + ));
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > + }
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Stop SD/MMC card clock.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > +
> > > + @retval EFI_SUCCESS Succeed to stop SD/MMC clock.
> > > + @retval Others Fail to stop SD/MMC clock.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcStopClock (
> > > + IN UINTN DevBase
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + UINT32 ClkEna;
> > > +
> > > + //
> > > + // Disable MMC clock first
> > > + //
> > > + ClkEna = 0;
> > > + MmioWrite32 (DevBase + DW_MMC_CLKENA, ClkEna);
> > > +
> > > + Status = DwMmcHcUpdateClock (DevBase);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + SD/MMC card clock supply.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] ClockFreq The max clock frequency to be set. The unit is
> > KHz.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The clock is supplied successfully.
> > > + @retval Others The clock isn't supplied successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcClockSupply (
> > > + IN UINTN DevBase,
> > > + IN UINT64 ClockFreq,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + UINT32 BaseClkFreq;
> > > + UINT32 SettingFreq;
> > > + UINT32 Divisor;
> > > + UINT32 Remainder;
> > > + UINT32 MmcStatus;
> > > + UINT32 ClkEna;
> > > + UINT32 ClkSrc;
> > > +
> > > + //
> > > + // Calculate a divisor for SD clock frequency
> > > + //
> > > + ASSERT (Capability.BaseClkFreq != 0);
> > > +
> > > + BaseClkFreq = Capability.BaseClkFreq;
> > > + if (ClockFreq == 0) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + if (ClockFreq > BaseClkFreq) {
> > > + ClockFreq = BaseClkFreq;
> > > + }
> > > +
> > > + //
> > > + // Calculate the divisor of base frequency.
> > > + //
> > > + Divisor = 0;
> > > + SettingFreq = BaseClkFreq;
> > > + while (ClockFreq < SettingFreq) {
> > > + Divisor++;
> > > +
> > > + SettingFreq = BaseClkFreq / (2 * Divisor);
> > > + Remainder = BaseClkFreq % (2 * Divisor);
> > > + if ((ClockFreq == SettingFreq) && (Remainder == 0)) {
> > > + break;
> > > + }
> > > + if ((ClockFreq == SettingFreq) && (Remainder != 0)) {
> > > + SettingFreq ++;
> > > + }
> > > + }
> > > +
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "BaseClkFreq %dKHz Divisor %d ClockFreq %dKhz\n",
> > > + BaseClkFreq,
> > > + Divisor,
> > > + ClockFreq
> > > + ));
> > > +
> > > + //
> > > + // Wait until MMC is idle
> > > + //
> > > + do {
> > > + MmcStatus = MmioRead32 (DevBase + DW_MMC_STATUS);
> > > + } while (MmcStatus & DW_MMC_STS_DATA_BUSY);
> > > +
> > > + do {
> > > + Status = DwMmcHcStopClock (DevBase);
> > > + } while (EFI_ERROR (Status));
> > > +
> > > + do {
> > > + ClkSrc = 0;
> > > + MmioWrite32 (DevBase + DW_MMC_CLKSRC, ClkSrc);
> > > + //
> > > + // Set clock divisor
> > > + //
> > > + MmioWrite32 (DevBase + DW_MMC_CLKDIV, Divisor);
> > > + //
> > > + // Enable MMC clock
> > > + //
> > > + ClkEna = 1;
> > > + MmioWrite32 (DevBase + DW_MMC_CLKENA, ClkEna);
> > > +
> > > + Status = DwMmcHcUpdateClock (DevBase);
> > > + } while (EFI_ERROR (Status));
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Set the SD/MMC bus width.
> > > +
> > > + Refer to SD Host Controller Simplified spec 3.0 Section 3.4 for details.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] IsDdr A boolean to indicate it's dual data rate or not.
> > > + @param[in] BusWidth The bus width used by the SD/MMC device, it
> > must be
> > > + 1, 4 or 8.
> > > +
> > > + @retval EFI_SUCCESS The bus width is set successfully.
> > > + @retval Others The bus width isn't set successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcSetBusWidth (
> > > + IN UINTN DevBase,
> > > + IN BOOLEAN IsDdr,
> > > + IN UINT16 BusWidth
> > > + )
> > > +{
> > > + UINT32 Ctype;
> > > + UINT32 Uhs;
> > > +
> > > + switch (BusWidth) {
> > > + case 1:
> > > + Ctype = MMC_1BIT_MODE;
> > > + break;
> > > + case 4:
> > > + Ctype = MMC_4BIT_MODE;
> > > + break;
> > > + case 8:
> > > + Ctype = MMC_8BIT_MODE;
> > > + break;
> > > + default:
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > + MmioWrite32 (DevBase + DW_MMC_CTYPE, Ctype);
> > > +
> > > + Uhs = MmioRead32 (DevBase + DW_MMC_UHSREG);
> > > +
> > > + if (IsDdr) {
> > > + Uhs |= UHS_DDR_MODE;
> > > + } else {
> > > + Uhs &= ~(UHS_DDR_MODE);
> > > + }
> > > +
> > > + MmioWrite32 (DevBase + DW_MMC_UHSREG, Uhs);
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Supply SD/MMC card with lowest clock frequency at initialization.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The clock is supplied successfully.
> > > + @retval Others The clock isn't supplied successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitClockFreq (
> > > + IN UINTN DevBase,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + UINT32 InitFreq;
> > > +
> > > + //
> > > + // Calculate a divisor for SD clock frequency
> > > + //
> > > + if (Capability.BaseClkFreq == 0) {
> > > + //
> > > + // Don't support get Base Clock Frequency information via another
> > method
> > > + //
> > > + return EFI_UNSUPPORTED;
> > > + }
> > > + //
> > > + // Supply 400KHz clock frequency at initialization phase.
> > > + //
> > > + InitFreq = DWMMC_INIT_CLOCK_FREQ;
> > > + Status = DwMmcHcClockSupply (DevBase, InitFreq, Capability);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + MicroSecondDelay (100);
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Supply SD/MMC card with maximum voltage at initialization.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The voltage is supplied successfully.
> > > + @retval Others The voltage isn't supplied successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitPowerVoltage (
> > > + IN UINTN DevBase,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + )
> > > +{
> > > + UINT32 Data;
> > > + UINT32 Timeout;
> > > +
> > > + Data = 0x1;
> > > + MmioWrite32 (DevBase + DW_MMC_PWREN, Data);
> > > +
> > > + Data = DW_MMC_CTRL_RESET_ALL;
> > > + MmioWrite32 (DevBase + DW_MMC_CTRL, Data);
> > > +
> > > + Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > + while (Timeout > 0) {
> > > + Data = MmioRead32 (DevBase + DW_MMC_CTRL);
> > > +
> > > + if ((Data & DW_MMC_CTRL_RESET_ALL) == 0) {
> > > + break;
> > > + }
> > > + gBS->Stall (1);
> > > +
> > > + Timeout--;
> > > + }
> > > +
> > > + if (Timeout <= 0) {
> > > + DEBUG ((DEBUG_INFO,
> > > + "DwMmcHcInitPowerVoltage: reset failed due to timeout"));
> > > +
> > > + return EFI_TIMEOUT;
> > > + }
> > > +
> > > + Data = DW_MMC_CTRL_INT_EN;
> > > + MmioWrite32 (DevBase + DW_MMC_CTRL, Data);
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Initialize the Timeout Control register with most conservative value at
> > > + initialization.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > +
> > > + @retval EFI_SUCCESS The timeout control register is configured
> > > + successfully.
> > > + @retval Others The timeout control register isn't configured
> > > + successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitTimeoutCtrl (
> > > + IN UINTN DevBase
> > > + )
> > > +{
> > > + UINT32 Data;
> > > +
> > > + Data = ~0;
> > > + MmioWrite32 (DevBase + DW_MMC_TMOUT, Data);
> > > +
> > > + Data = 0x00FFFFFF;
> > > + MmioWrite32 (DevBase + DW_MMC_DEBNCE, Data);
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Initial SD/MMC host controller with lowest clock frequency, max power
> > and
> > > + max timeout value at initialization.
> > > +
> > > + @param[in] DevIo The DEVICE IO protocol instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command
> > > + to.
> > > + @param[in] Capability The capability of the slot.
> > > +
> > > + @retval EFI_SUCCESS The host controller is initialized successfully.
> > > + @retval Others The host controller isn't initialized successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcHcInitHost (
> > > + IN UINTN DevBase,
> > > + IN DW_MMC_HC_SLOT_CAP Capability
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > +
> > > + Status = DwMmcHcInitPowerVoltage (DevBase, Capability);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + return Status;
> > > +}
> > > +
> > > +EFI_STATUS
> > > +DwMmcHcStartDma (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + UINTN DevBase;
> > > + UINT32 Ctrl;
> > > + UINT32 Bmod;
> > > + UINT32 Timeout;
> > > + UINT32 Data;
> > > +
> > > +// DevIo = Trb->Private->DevIo;
> > > + DevBase = Trb->Private->DevBase;
> > > +
> > > + //
> > > + // Reset DMA
> > > + //
> > > + Ctrl = DW_MMC_CTRL_DMA_RESET;
> > > + MmioWrite32 (DevBase + DW_MMC_CTRL, Ctrl);
> > > +
> > > + Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > + while (Timeout > 0) {
> > > + Data = MmioRead32 (DevBase + DW_MMC_CTRL);
> > > +
> > > + if ((Data & DW_MMC_CTRL_DMA_RESET) == 0) {
> > > + break;
> > > + }
> > > + gBS->Stall (1);
> > > +
> > > + Timeout--;
> > > + }
> > > +
> > > + if (Timeout <= 0) {
> > > + DEBUG ((DEBUG_ERROR, "Timed out waiting for CTRL_DMA_RESET"));
> > > +
> > > + return EFI_TIMEOUT;
> > > + }
> > > +
> > > + Bmod = DW_MMC_IDMAC_SWRESET | MmioRead32 (DevBase +
> > DW_MMC_BMOD);
> > > +
> > > + MmioWrite32 (DevBase + DW_MMC_BMOD, Bmod);
> > > +
> > > + //
> > > + // Select IDMAC
> > > + //
> > > + Ctrl = DW_MMC_CTRL_IDMAC_EN;
> > > + Ctrl |= MmioRead32 (DevBase + DW_MMC_CTRL);
> > > + MmioWrite32 (DevBase + DW_MMC_CTRL, Ctrl);
> > > +
> > > + //
> > > + // Enable IDMAC
> > > + //
> > > + Bmod = DW_MMC_IDMAC_ENABLE | DW_MMC_IDMAC_FB;
> > > + Bmod |= MmioRead32 (DevBase + DW_MMC_BMOD);
> > > +
> > > + MmioWrite32 (DevBase + DW_MMC_BMOD, Bmod);
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +EFI_STATUS
> > > +DwMmcHcStopDma (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + UINTN DevBase;
> > > + UINT32 Ctrl;
> > > + UINT32 Bmod;
> > > +
> > > + DevBase = Trb->Private->DevBase;
> > > +
> > > + //
> > > + // Disable and reset IDMAC
> > > + //
> > > + Ctrl = MmioRead32 (DevBase + DW_MMC_CTRL);
> > > + Ctrl &= ~DW_MMC_CTRL_IDMAC_EN;
> > > + Ctrl |= DW_MMC_CTRL_DMA_RESET;
> > > + MmioWrite32 (DevBase + DW_MMC_CTRL, Ctrl);
> > > +
> > > + //
> > > + // Stop IDMAC
> > > + //
> > > + Bmod = MmioRead32 (DevBase + DW_MMC_BMOD);
> > > + Bmod &= ~(DW_MMC_BMOD_FB | DW_MMC_BMOD_DE);
> > > + Bmod |= DW_MMC_BMOD_SWR;
> > > + MmioWrite32 (DevBase + DW_MMC_BMOD, Bmod);
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Build DMA descriptor table for transfer.
> > > +
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > + @retval EFI_SUCCESS The DMA descriptor table is created
> > successfully.
> > > + @retval Others The DMA descriptor table isn't created
> successfully.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +BuildDmaDescTable (
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + EFI_PHYSICAL_ADDRESS Data;
> > > + UINT64 DataLen;
> > > + UINT64 Entries;
> > > + UINT32 Index;
> > > + UINT64 Remaining;
> > > + UINTN TableSize;
> > > + UINTN DevBase;
> > > + EFI_STATUS Status;
> > > + UINTN Bytes;
> > > + UINTN Blocks;
> > > + DW_MMC_HC_DMA_DESC_LINE *DmaDesc;
> > > + UINT32 DmaDescPhy;
> > > + UINT32 Idsts;
> > > + UINT32 BytCnt;
> > > + UINT32 BlkSize;
> > > +
> > > + Data = Trb->DataPhy;
> > > + DataLen = Trb->DataLen;
> > > + DevBase = Trb->Private->DevBase;
> > > + //
> > > + // Only support 32bit DMA Descriptor Table
> > > + //
> > > + if ((Data >= 0x100000000ul) || ((Data + DataLen) > 0x100000000ul)) {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > + //
> > > + // Address field shall be set on 32-bit boundary (Lower 2-bit is always
> set
> > > + // to 0) for 32-bit address descriptor table.
> > > + //
> > > + if ((Data & (BIT0 | BIT1)) != 0) {
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "The buffer [0x%x] to construct DMA desc is not aligned to 4
> bytes!\n",
> > > + Data
> > > + ));
> > > + }
> > > +
> > > + Entries = (DataLen + DWMMC_DMA_BUF_SIZE - 1) /
> > DWMMC_DMA_BUF_SIZE;
> > > + TableSize = Entries * sizeof (DW_MMC_HC_DMA_DESC_LINE);
> > > + Blocks = (DataLen + DW_MMC_BLOCK_SIZE - 1) /
> > DW_MMC_BLOCK_SIZE;
> > > +
> > > + Trb->DmaDescPages = (UINT32)EFI_SIZE_TO_PAGES (Entries *
> > DWMMC_DMA_BUF_SIZE);
> > > +/* Status = DevIo->AllocateBuffer (
> > > + DevIo,
> > > + AllocateAnyPages,
> > > + EfiBootServicesData,
> > > + EFI_SIZE_TO_PAGES (TableSize),
> > > + (EFI_PHYSICAL_ADDRESS *)&Trb->DmaDesc
> > > + );*/
> > > + Status = DmaAllocateBuffer (EfiBootServicesData, EFI_SIZE_TO_PAGES
> > (TableSize),
> > > + (VOID *)&Trb->DmaDesc);
> > > + if (EFI_ERROR (Status)) {
> > > + return EFI_OUT_OF_RESOURCES;
> > > + }
> > > +
> > > + ZeroMem (Trb->DmaDesc, TableSize);
> > > + Bytes = TableSize;
> > > +
> > > + Status = DmaMap (MapOperationBusMasterCommonBuffer,
> > > + (EFI_PHYSICAL_ADDRESS *)Trb->DmaDesc,
> > > + &Bytes, &Trb->DmaDescPhy, &Trb->DmaMap);
> > > +/* Status = DevIo->Map (
> > > + DevIo,
> > > + EfiBusMasterCommonBuffer,
> > > + (EFI_PHYSICAL_ADDRESS *)Trb->DmaDesc,
> > > + &Bytes,
> > > + &Trb->DmaDescPhy,
> > > + &Trb->DmaMap
> > > + );*/
> > > +
> > > + if (EFI_ERROR (Status) || (Bytes != TableSize)) {
> > > + //
> > > + // Map error or unable to map the whole RFis buffer into a contiguous
> > > + // region.
> > > + //
> > > +/* DevIo->FreeBuffer (
> > > + DevIo,
> > > + EFI_SIZE_TO_PAGES (TableSize),
> > > + (EFI_PHYSICAL_ADDRESS)Trb->DmaDesc
> > > + );*/
> > > + return EFI_OUT_OF_RESOURCES;
> > > + }
> > > +
> > > + if ((UINT64)(UINTN)Trb->DmaDescPhy > 0x100000000ul) {
> > > + //
> > > + // The DMA doesn't support 64bit addressing.
> > > + //
> > > + DmaUnmap (Trb->DmaMap);
> > > +/* DevIo->Unmap (
> > > + DevIo,
> > > + Trb->DmaMap
> > > + );*/
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > +
> > > + if (DataLen < DW_MMC_BLOCK_SIZE) {
> > > + BlkSize = DataLen;
> > > + BytCnt = DataLen;
> > > + Remaining = DataLen;
> > > + } else {
> > > + BlkSize = DW_MMC_BLOCK_SIZE;
> > > + BytCnt = DW_MMC_BLOCK_SIZE * Blocks;
> > > + Remaining = DW_MMC_BLOCK_SIZE * Blocks;
> > > + }
> > > +
> > > + MmioWrite32 (DevBase + DW_MMC_BLKSIZ, BlkSize);
> > > + MmioWrite32 (DevBase + DW_MMC_BYTCNT, BytCnt);
> > > + DmaDesc = Trb->DmaDesc;
> > > + for (Index = 0; Index < Entries; Index++, DmaDesc++) {
> > > + DmaDesc->Des0 = DW_MMC_IDMAC_DES0_OWN |
> > DW_MMC_IDMAC_DES0_CH |
> > > + DW_MMC_IDMAC_DES0_DIC;
> > > + DmaDesc->Des1 = DW_MMC_IDMAC_DES1_BS1
> > (DWMMC_DMA_BUF_SIZE);
> > > + //
> > > + // Buffer Address
> > > + //
> > > + DmaDesc->Des2 = (UINT32)((UINTN)Trb->DataPhy +
> > > + (DWMMC_DMA_BUF_SIZE * Index));
> > > + //
> > > + // Next Descriptor Address
> > > + //
> > > + DmaDesc->Des3 = (UINT32)((UINTN)Trb->DmaDescPhy +
> > > + sizeof (DW_MMC_HC_DMA_DESC_LINE) * (Index + 1));
> > > + Remaining = Remaining - DWMMC_DMA_BUF_SIZE;
> > > + }
> > > + //
> > > + // First Descriptor
> > > + //
> > > + Trb->DmaDesc[0].Des0 |= DW_MMC_IDMAC_DES0_FS;
> > > + //
> > > + // Last Descriptor
> > > + //
> > > + Trb->DmaDesc[Entries - 1].Des0 &= ~(DW_MMC_IDMAC_DES0_CH |
> > > + DW_MMC_IDMAC_DES0_DIC);
> > > + Trb->DmaDesc[Entries - 1].Des0 |= DW_MMC_IDMAC_DES0_OWN |
> > > + DW_MMC_IDMAC_DES0_LD;
> > > + Trb->DmaDesc[Entries - 1].Des1 = DW_MMC_IDMAC_DES1_BS1
> > (Remaining +
> > > + DWMMC_DMA_BUF_SIZE);
> > > + //
> > > + // Set the next field of the Last Descriptor
> > > + //
> > > + Trb->DmaDesc[Entries - 1].Des3 = 0;
> > > + DmaDescPhy = (UINT32)Trb->DmaDescPhy;
> > > +
> > > + MmioWrite32 (DevBase + DW_MMC_DBADDR, DmaDescPhy);
> > > +
> > > + ArmDataSynchronizationBarrier ();
> > > + ArmInstructionSynchronizationBarrier ();
> > > + //
> > > + // Clear interrupts
> > > + //
> > > + Idsts = ~0;
> > > + MmioWrite32 (DevBase + DW_MMC_IDSTS, Idsts);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +EFI_STATUS
> > > +TransferFifo (
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + UINTN DevBase;
> > > + UINT32 Data;
> > > + UINT32 Received;
> > > + UINT32 Count;
> > > + UINT32 Intsts;
> > > + UINT32 Sts;
> > > + UINT32 FifoCount;
> > > + UINT32 Index; /* count with bytes */
> > > + UINT32 Ascending;
> > > + UINT32 Descending;
> > > +
> > > + DevBase = Trb->Private->DevBase;
> > > + Received = 0;
> > > + Count = 0;
> > > + Index = 0;
> > > + Ascending = 0;
> > > + Descending = ((Trb->DataLen + 3) & ~3) - 4;
> > > + do {
> > > + Intsts = MmioRead32 (DevBase + DW_MMC_RINTSTS);
> > > +
> > > + if (Trb->DataLen && (Intsts & DW_MMC_INT_TXDR) && !Trb->Read) {
> > > + Sts = MmioRead32 (DevBase + DW_MMC_STATUS);
> > > +
> > > + while (!(DW_MMC_STS_FIFO_FULL(Sts))
> > > + && (Received < Trb->DataLen)
> > > + && (Intsts & DW_MMC_INT_TXDR)) {
> > > + if (Trb->UseBE) {
> > > + Data = SwapBytes32 (*(UINT32 *)((UINTN)Trb->Data +
> Descending));
> > > + Descending = Descending - 4;
> > > + } else {
> > > + Data = *(UINT32 *)((UINTN)Trb->Data + Ascending);
> > > + Ascending += 4;
> > > + }
> > > + Index += 4;
> > > + Received += 4;
> > > +
> > > + MmioWrite32 (DevBase + DW_MMC_FIFO_START, Data);
> > > +
> > > + Intsts = DW_MMC_INT_TXDR;
> > > + MmioWrite32 (DevBase + DW_MMC_RINTSTS, Intsts);
> > > +
> > > + Intsts = MmioRead32 (DevBase + DW_MMC_RINTSTS);
> > > + Sts = MmioRead32 (DevBase + DW_MMC_STATUS);
> > > + }
> > > + continue;
> > > + }
> > > +
> > > + if (Trb->DataLen && ((Intsts & DW_MMC_INT_RXDR) ||
> > > + (Intsts & DW_MMC_INT_DTO)) && Trb->Read) {
> > > + Sts = MmioRead32 (DevBase + DW_MMC_STATUS);
> > > + //
> > > + // Convert to bytes
> > > + //
> > > + FifoCount = GET_STS_FIFO_COUNT (Sts) << 2;
> > > + if ((FifoCount == 0) && (Received < Trb->DataLen)) {
> > > + continue;
> > > + }
> > > + Index = 0;
> > > + Count = (MIN (FifoCount, Trb->DataLen) + 3) & ~3;
> > > + while (Index < Count) {
> > > + Data = MmioRead32 (DevBase + DW_MMC_FIFO_START);
> > > +
> > > + if (Trb->UseBE) {
> > > + *(UINT32 *)((UINTN)Trb->Data + Descending) = SwapBytes32
> (Data);
> > > + Descending = Descending - 4;
> > > + } else {
> > > + *(UINT32 *)((UINTN)Trb->Data + Ascending) = Data;
> > > + Ascending += 4;
> > > + }
> > > + Index += 4;
> > > + Received += 4;
> > > + } /* while */
> > > + } /* if */
> > > + } while (((Intsts & DW_MMC_INT_CMD_DONE) == 0) || (Received <
> Trb-
> > >DataLen));
> > > + //
> > > + // Clear RINTSTS
> > > + //
> > > + Intsts = ~0;
> > > + MmioWrite32 (DevBase + DW_MMC_RINTSTS, Intsts);
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Create a new TRB for the SD/MMC cmd request.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command
> > > + to.
> > > + @param[in] Packet A pointer to the SD command data structure.
> > > + @param[in] Event If Event is NULL, blocking I/O is performed. If
> > > + Event is not NULL, then nonblocking I/O is
> > > + performed, and Event will be signaled when the
> > > + Packet completes.
> > > +
> > > + @return Created Trb or NULL.
> > > +
> > > +**/
> > > +DW_MMC_HC_TRB *
> > > +DwMmcCreateTrb (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN UINT8 Slot,
> > > + IN EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet,
> > > + IN EFI_EVENT Event
> > > + )
> > > +{
> > > + DW_MMC_HC_TRB *Trb;
> > > + EFI_STATUS Status;
> > > + EFI_TPL OldTpl;
> > > + EFI_IO_OPERATION_TYPE Flag;
> > > + UINTN MapLength;
> > > +
> > > + Trb = AllocateZeroPool (sizeof (DW_MMC_HC_TRB));
> > > + if (Trb == NULL) {
> > > + return NULL;
> > > + }
> > > +
> > > + Trb->Signature = DW_MMC_HC_TRB_SIG;
> > > + Trb->Slot = Slot;
> > > + Trb->BlockSize = 0x200;
> > > + Trb->Packet = Packet;
> > > + Trb->Event = Event;
> > > + Trb->Started = FALSE;
> > > + Trb->Timeout = Packet->Timeout;
> > > + Trb->Private = Private;
> > > +
> > > + if ((Packet->InTransferLength != 0) && (Packet->InDataBuffer !=
> NULL)) {
> > > + Trb->Data = Packet->InDataBuffer;
> > > + Trb->DataLen = Packet->InTransferLength;
> > > + Trb->Read = TRUE;
> > > + ZeroMem (Trb->Data, Trb->DataLen);
> > > + } else if (Packet->OutTransferLength && (Packet->OutDataBuffer !=
> > NULL)) {
> > > + Trb->Data = Packet->OutDataBuffer;
> > > + Trb->DataLen = Packet->OutTransferLength;
> > > + Trb->Read = FALSE;
> > > + } else if (!Packet->InTransferLength && !Packet->OutTransferLength) {
> > > + Trb->Data = NULL;
> > > + Trb->DataLen = 0;
> > > + } else {
> > > + goto Error;
> > > + }
> > > +
> > > + if (((Private->Slot[Trb->Slot].CardType == EmmcCardType) &&
> > > + (Packet->SdMmcCmdBlk->CommandIndex ==
> > EMMC_SEND_TUNING_BLOCK)) ||
> > > + ((Private->Slot[Trb->Slot].CardType == SdCardType) &&
> > > + (Packet->SdMmcCmdBlk->CommandIndex ==
> > SD_SEND_TUNING_BLOCK))) {
> > > + Trb->Mode = SdMmcPioMode;
> > > + } else {
> > > + if (Trb->Read) {
> > > + Flag = EfiBusMasterWrite;
> > > + } else {
> > > + Flag = EfiBusMasterRead;
> > > + }
> > > +
> > > + if (Private->Slot[Trb->Slot].CardType == SdCardType) {
> > > + Trb->UseFifo = TRUE;
> > > + } else {
> > > + Trb->UseFifo = FALSE;
> > > + if (Trb->DataLen) {
> > > + MapLength = Trb->DataLen;
> > > + Status = DmaMap (Flag, Trb->Data, &MapLength, &Trb->DataPhy,
> > &Trb->DataMap);
> > > +/* Status = DevIo->Map (
> > > + DevIo,
> > > + Flag,
> > > + Trb->Data,
> > > + &MapLength,
> > > + &Trb->DataPhy,
> > > + &Trb->DataMap
> > > + );*/
> > > + if (EFI_ERROR (Status) || (Trb->DataLen != MapLength)) {
> > > + Status = EFI_BAD_BUFFER_SIZE;
> > > + goto Error;
> > > + }
> > > +
> > > + Status = BuildDmaDescTable (Trb);
> > > + if (EFI_ERROR (Status)) {
> > > + DmaUnmap(Trb->DataMap);
> > > + goto Error;
> > > + }
> > > + Status = DwMmcHcStartDma (Private, Trb);
> > > + if (EFI_ERROR (Status)) {
> > > + DmaUnmap(Trb->DataMap);
> > > + goto Error;
> > > + }
> > > + }
> > > + }
> > > + } /* TuningBlock */
> > > +
> > > + if (Event != NULL) {
> > > + OldTpl = gBS->RaiseTPL (TPL_NOTIFY);
> > > + InsertTailList (&Private->Queue, &Trb->TrbList);
> > > + gBS->RestoreTPL (OldTpl);
> > > + }
> > > +
> > > + return Trb;
> > > +
> > > +Error:
> > > + return NULL;
> > > +}
> > > +
> > > +/**
> > > + Free the resource used by the TRB.
> > > +
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > +**/
> > > +VOID
> > > +DwMmcFreeTrb (
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + if (Trb->DmaMap != NULL) {
> > > + DmaUnmap (Trb->DmaMap);
> > > + }
> > > + if (Trb->DataMap != NULL) {
> > > + DmaUnmap (Trb->DataMap);
> > > + }
> > > + FreePool (Trb);
> > > +}
> > > +
> > > +/**
> > > + Check if the env is ready for execute specified TRB.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > + @retval EFI_SUCCESS The env is ready for TRB execution.
> > > + @retval EFI_NOT_READY The env is not ready for TRB execution.
> > > + @retval Others Some erros happen.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcCheckTrbEnv (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Wait for the env to be ready for execute specified TRB.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > + @retval EFI_SUCCESS The env is ready for TRB execution.
> > > + @retval EFI_TIMEOUT The env is not ready for TRB execution in
> time.
> > > + @retval Others Some erros happen.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcWaitTrbEnv (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet;
> > > + UINT64 Timeout;
> > > + BOOLEAN InfiniteWait;
> > > +
> > > + //
> > > + // Wait Command Complete Interrupt Status bit in Normal Interrupt
> > Status
> > > + // Register
> > > + //
> > > + Packet = Trb->Packet;
> > > + Timeout = Packet->Timeout;
> > > + if (Timeout == 0) {
> > > + InfiniteWait = TRUE;
> > > + } else {
> > > + InfiniteWait = FALSE;
> > > + }
> > > +
> > > + while (InfiniteWait || (Timeout > 0)) {
> > > + //
> > > + // Check Trb execution result by reading Normal Interrupt Status
> > register.
> > > + //
> > > + Status = DwMmcCheckTrbEnv (Private, Trb);
> > > + if (Status != EFI_NOT_READY) {
> > > + return Status;
> > > + }
> > > + //
> > > + // Stall for 1 microsecond.
> > > + //
> > > + gBS->Stall (1);
> > > +
> > > + Timeout--;
> > > + }
> > > +
> > > + return EFI_TIMEOUT;
> > > +}
> > > +
> > > +EFI_STATUS
> > > +DwEmmcExecTrb (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet;
> > > + UINTN DevBase;
> > > + UINT32 Cmd;
> > > + UINT32 MmcStatus;
> > > + UINT32 IntStatus;
> > > + UINT32 Argument;
> > > + UINT32 ErrMask;
> > > + UINT32 Timeout;
> > > +
> > > + Packet = Trb->Packet;
> > > + DevBase = Trb->Private->DevBase;
> > > +
> > > + ArmDataSynchronizationBarrier ();
> > > + ArmInstructionSynchronizationBarrier ();
> > > + //
> > > + // Wait until MMC is idle
> > > + //
> > > + do {
> > > + MmcStatus = MmioRead32 (DevBase + DW_MMC_STATUS);
> > > + } while (MmcStatus & DW_MMC_STS_DATA_BUSY);
> > > +
> > > + IntStatus = ~0;
> > > + MmioWrite32 (DevBase + DW_MMC_RINTSTS, IntStatus);
> > > + Cmd = CMD_INDEX (Packet->SdMmcCmdBlk->CommandIndex);
> > > + if ((Packet->SdMmcCmdBlk->CommandType ==
> > SdMmcCommandTypeAc) ||
> > > + (Packet->SdMmcCmdBlk->CommandType ==
> > SdMmcCommandTypeAdtc)) {
> > > + switch (Packet->SdMmcCmdBlk->CommandIndex) {
> > > + case EMMC_SET_RELATIVE_ADDR:
> > > + Cmd |= BIT_CMD_SEND_INIT;
> > > + break;
> > > + case EMMC_SEND_STATUS:
> > > + Cmd |= BIT_CMD_WAIT_PRVDATA_COMPLETE;
> > > + break;
> > > + case EMMC_STOP_TRANSMISSION:
> > > + Cmd |= BIT_CMD_STOP_ABORT_CMD;
> > > + break;
> > > + }
> > > + if (Packet->InTransferLength) {
> > > + Cmd |= BIT_CMD_WAIT_PRVDATA_COMPLETE |
> > BIT_CMD_DATA_EXPECTED |
> > > + BIT_CMD_READ;
> > > + } else if (Packet->OutTransferLength) {
> > > + Cmd |= BIT_CMD_WAIT_PRVDATA_COMPLETE |
> > BIT_CMD_DATA_EXPECTED |
> > > + BIT_CMD_WRITE;
> > > + }
> > > + Cmd |= BIT_CMD_RESPONSE_EXPECT |
> > BIT_CMD_CHECK_RESPONSE_CRC;
> > > + } else {
> > > + switch (Packet->SdMmcCmdBlk->CommandIndex) {
> > > + case EMMC_GO_IDLE_STATE:
> > > + Cmd |= BIT_CMD_SEND_INIT;
> > > + break;
> > > + case EMMC_SEND_OP_COND:
> > > + Cmd |= BIT_CMD_RESPONSE_EXPECT;
> > > + break;
> > > + case EMMC_ALL_SEND_CID:
> > > + Cmd |= BIT_CMD_RESPONSE_EXPECT | BIT_CMD_LONG_RESPONSE
> |
> > > + BIT_CMD_CHECK_RESPONSE_CRC | BIT_CMD_SEND_INIT;
> > > + break;
> > > + }
> > > + }
> > > + switch (Packet->SdMmcCmdBlk->ResponseType) {
> > > + case SdMmcResponseTypeR2:
> > > + Cmd |= BIT_CMD_RESPONSE_EXPECT |
> > BIT_CMD_CHECK_RESPONSE_CRC |
> > > + BIT_CMD_LONG_RESPONSE;
> > > + break;
> > > + case SdMmcResponseTypeR3:
> > > + Cmd |= BIT_CMD_RESPONSE_EXPECT;
> > > + break;
> > > + }
> > > + Cmd |= BIT_CMD_USE_HOLD_REG | BIT_CMD_START;
> > > +
> > > + Argument = Packet->SdMmcCmdBlk->CommandArgument;
> > > + MmioWrite32 (DevBase + DW_MMC_CMDARG, Argument);
> > > +
> > > + ArmDataSynchronizationBarrier ();
> > > + ArmInstructionSynchronizationBarrier ();
> > > +
> > > + MmioWrite32 (DevBase + DW_MMC_CMD, Cmd);
> > > + ArmDataSynchronizationBarrier ();
> > > + ArmInstructionSynchronizationBarrier ();
> > > +
> > > + ErrMask = DW_MMC_INT_EBE | DW_MMC_INT_HLE |
> > DW_MMC_INT_RTO |
> > > + DW_MMC_INT_RCRC | DW_MMC_INT_RE;
> > > + ErrMask |= DW_MMC_INT_DCRC | DW_MMC_INT_DRT |
> > DW_MMC_INT_SBE;
> > > + do {
> > > + Timeout = 10000;
> > > + if (--Timeout == 0) {
> > > + break;
> > > + }
> > > + IntStatus = MmioRead32 (DevBase + DW_MMC_RINTSTS);
> > > + if (IntStatus & ErrMask) {
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > + if (Trb->DataLen && ((IntStatus & DW_MMC_INT_DTO) == 0)) {
> > > + //
> > > + // Transfer Not Done
> > > + //
> > > + MicroSecondDelay (10);
> > > + continue;
> > > + }
> > > + MicroSecondDelay (10);
> > > + } while (!(IntStatus & DW_MMC_INT_CMD_DONE));
> > > + switch (Packet->SdMmcCmdBlk->ResponseType) {
> > > + case SdMmcResponseTypeR1:
> > > + case SdMmcResponseTypeR1b:
> > > + case SdMmcResponseTypeR3:
> > > + case SdMmcResponseTypeR4:
> > > + case SdMmcResponseTypeR5:
> > > + Packet->SdMmcStatusBlk->Resp0 = MmioRead32 (DevBase +
> > DW_MMC_RESP0);
> > > + break;
> > > + case SdMmcResponseTypeR2:
> > > + Packet->SdMmcStatusBlk->Resp0 = MmioRead32 (DevBase +
> > DW_MMC_RESP0);
> > > + Packet->SdMmcStatusBlk->Resp1 = MmioRead32 (DevBase +
> > DW_MMC_RESP1);
> > > + Packet->SdMmcStatusBlk->Resp2 = MmioRead32 (DevBase +
> > DW_MMC_RESP2);
> > > + Packet->SdMmcStatusBlk->Resp3 = MmioRead32 (DevBase +
> > DW_MMC_RESP3);
> > > + break;
> > > + }
> > > +
> > > + //
> > > + // The workaround on EMMC_SEND_CSD is used to be compatible with
> > SDHC.
> > > + //
> > > + if (Packet->SdMmcCmdBlk->CommandIndex == EMMC_SEND_CSD) {
> > > + {
> > > + UINT32 Buf[4];
> > > + ZeroMem (Buf, sizeof (Buf));
> > > + CopyMem (
> > > + (UINT8 *)Buf,
> > > + (UINT8 *)&Packet->SdMmcStatusBlk->Resp0 + 1,
> > > + sizeof (Buf) - 1
> > > + );
> > > + CopyMem (
> > > + (UINT8 *)&Packet->SdMmcStatusBlk->Resp0,
> > > + (UINT8 *)Buf,
> > > + sizeof (Buf) - 1
> > > + );
> > > + }
> > > + }
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +EFI_STATUS
> > > +DwSdExecTrb (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet;
> > > + UINTN DevBase;
> > > + UINT32 Cmd;
> > > + UINT32 MmcStatus;
> > > + UINT32 IntStatus;
> > > + UINT32 Argument;
> > > + UINT32 ErrMask;
> > > + UINT32 Timeout;
> > > + UINT32 Idsts;
> > > + UINT32 BytCnt;
> > > + UINT32 BlkSize;
> > > + EFI_STATUS Status;
> > > +
> > > + Packet = Trb->Packet;
> > > + DevBase = Trb->Private->DevBase;
> > > +
> > > + ArmDataSynchronizationBarrier ();
> > > + ArmInstructionSynchronizationBarrier ();
> > > + //
> > > + // Wait until MMC is idle
> > > + //
> > > + do {
> > > + MmcStatus = MmioRead32 (DevBase + DW_MMC_STATUS);
> > > + } while (MmcStatus & DW_MMC_STS_DATA_BUSY);
> > > +
> > > + IntStatus = ~0;
> > > + MmioWrite32 (DevBase + DW_MMC_RINTSTS, IntStatus);
> > > + Cmd = CMD_INDEX (Packet->SdMmcCmdBlk->CommandIndex);
> > > + if ((Packet->SdMmcCmdBlk->CommandType ==
> > SdMmcCommandTypeAc) ||
> > > + (Packet->SdMmcCmdBlk->CommandType ==
> > SdMmcCommandTypeAdtc)) {
> > > + switch (Packet->SdMmcCmdBlk->CommandIndex) {
> > > + case SD_SET_RELATIVE_ADDR:
> > > + Cmd |= BIT_CMD_SEND_INIT;
> > > + break;
> > > + case SD_STOP_TRANSMISSION:
> > > + Cmd |= BIT_CMD_STOP_ABORT_CMD;
> > > + break;
> > > + case SD_SEND_SCR:
> > > + Trb->UseBE = TRUE;
> > > + break;
> > > + }
> > > + if (Packet->InTransferLength) {
> > > + Cmd |= BIT_CMD_WAIT_PRVDATA_COMPLETE |
> > BIT_CMD_DATA_EXPECTED |
> > > + BIT_CMD_READ;
> > > + } else if (Packet->OutTransferLength) {
> > > + Cmd |= BIT_CMD_WAIT_PRVDATA_COMPLETE |
> > BIT_CMD_DATA_EXPECTED |
> > > + BIT_CMD_WRITE;
> > > + }
> > > + Cmd |= BIT_CMD_RESPONSE_EXPECT |
> > BIT_CMD_CHECK_RESPONSE_CRC |
> > > + BIT_CMD_SEND_AUTO_STOP;
> > > + } else {
> > > + switch (Packet->SdMmcCmdBlk->CommandIndex) {
> > > + case SD_GO_IDLE_STATE:
> > > + Cmd |= BIT_CMD_SEND_INIT;
> > > + break;
> > > + }
> > > + }
> > > + switch (Packet->SdMmcCmdBlk->ResponseType) {
> > > + case SdMmcResponseTypeR2:
> > > + Cmd |= BIT_CMD_RESPONSE_EXPECT |
> > BIT_CMD_CHECK_RESPONSE_CRC |
> > > + BIT_CMD_LONG_RESPONSE;
> > > + break;
> > > + case SdMmcResponseTypeR3:
> > > + Cmd |= BIT_CMD_RESPONSE_EXPECT;
> > > + break;
> > > + case SdMmcResponseTypeR1b:
> > > + case SdMmcResponseTypeR4:
> > > + case SdMmcResponseTypeR6:
> > > + case SdMmcResponseTypeR7:
> > > + Cmd |= BIT_CMD_RESPONSE_EXPECT |
> > BIT_CMD_CHECK_RESPONSE_CRC;
> > > + break;
> > > + }
> > > + Cmd |= BIT_CMD_USE_HOLD_REG | BIT_CMD_START;
> > > +
> > > + if (Trb->UseFifo == TRUE) {
> > > + BytCnt = Trb->Read ? Packet->InTransferLength : Packet-
> > >OutTransferLength;
> > > + MmioWrite32 (DevBase + DW_MMC_BYTCNT, BytCnt);
> > > + if (Trb->Read) {
> > > + if (Packet->InTransferLength > DW_MMC_BLOCK_SIZE) {
> > > + BlkSize = DW_MMC_BLOCK_SIZE;
> > > + } else {
> > > + BlkSize = Packet->InTransferLength;
> > > + }
> > > + }
> > > + else {
> > > + if (Packet->OutTransferLength > DW_MMC_BLOCK_SIZE) {
> > > + BlkSize = DW_MMC_BLOCK_SIZE;
> > > + } else {
> > > + BlkSize = Packet->OutTransferLength;
> > > + }
> > > + }
> > > +
> > > + MmioWrite32 (DevBase + DW_MMC_BLKSIZ, BlkSize);
> > > + }
> > > +
> > > + Argument = Packet->SdMmcCmdBlk->CommandArgument;
> > > + MmioWrite32 (DevBase + DW_MMC_CMDARG, Argument);
> > > + ArmDataSynchronizationBarrier ();
> > > + ArmInstructionSynchronizationBarrier ();
> > > + MmioWrite32 (DevBase + DW_MMC_CMD, Cmd);
> > > + ArmDataSynchronizationBarrier ();
> > > + ArmInstructionSynchronizationBarrier ();
> > > +
> > > + ErrMask = DW_MMC_INT_EBE | DW_MMC_INT_HLE |
> > DW_MMC_INT_RTO |
> > > + DW_MMC_INT_RCRC | DW_MMC_INT_RE;
> > > + ErrMask |= DW_MMC_INT_DRT | DW_MMC_INT_SBE;
> > > + if (Packet->InTransferLength || Packet->OutTransferLength) {
> > > + ErrMask |= DW_MMC_INT_DCRC;
> > > + }
> > > + if (Trb->UseFifo == TRUE) {
> > > + Status = TransferFifo (Trb);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + } else {
> > > + Timeout = 10000;
> > > + do {
> > > + if (--Timeout == 0) {
> > > + break;
> > > + }
> > > + IntStatus = MmioRead32 (DevBase + DW_MMC_RINTSTS);
> > > + if (IntStatus & ErrMask) {
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > + if (Trb->DataLen && ((IntStatus & DW_MMC_INT_DTO) == 0)) {
> > > + //
> > > + // Transfer not Done
> > > + //
> > > + MicroSecondDelay (10);
> > > + continue;
> > > + }
> > > + MicroSecondDelay (10);
> > > + } while (!(IntStatus & DW_MMC_INT_CMD_DONE));
> > > + if (Packet->InTransferLength) {
> > > + do {
> > > + Idsts = MmioRead32 (DevBase + DW_MMC_IDSTS);
> > > + } while ((Idsts & DW_MMC_IDSTS_RI) == 0);
> > > + Status = DwMmcHcStopDma (Private, Trb);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + } else if (Packet->OutTransferLength) {
> > > + do {
> > > + Idsts = MmioRead32 (DevBase + DW_MMC_IDSTS);
> > > + } while ((Idsts & DW_MMC_IDSTS_TI) == 0);
> > > + Status = DwMmcHcStopDma (Private, Trb);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + } /* Packet->InTransferLength */
> > > + } /* UseFifo */
> > > + switch (Packet->SdMmcCmdBlk->ResponseType) {
> > > + case SdMmcResponseTypeR1:
> > > + case SdMmcResponseTypeR1b:
> > > + case SdMmcResponseTypeR3:
> > > + case SdMmcResponseTypeR4:
> > > + case SdMmcResponseTypeR5:
> > > + case SdMmcResponseTypeR6:
> > > + case SdMmcResponseTypeR7:
> > > + Packet->SdMmcStatusBlk->Resp0 = MmioRead32 (DevBase +
> > DW_MMC_RESP0);
> > > + break;
> > > + case SdMmcResponseTypeR2:
> > > + Packet->SdMmcStatusBlk->Resp0 = MmioRead32 (DevBase +
> > DW_MMC_RESP0);
> > > + Packet->SdMmcStatusBlk->Resp1 = MmioRead32 (DevBase +
> > DW_MMC_RESP1);
> > > + Packet->SdMmcStatusBlk->Resp2 = MmioRead32 (DevBase +
> > DW_MMC_RESP2);
> > > + Packet->SdMmcStatusBlk->Resp3 = MmioRead32 (DevBase +
> > DW_MMC_RESP3);
> > > + break;
> > > + }
> > > +
> > > + //
> > > + // The workaround on SD_SEND_CSD is used to be compatible with
> > SDHC.
> > > + //
> > > + if (Packet->SdMmcCmdBlk->CommandIndex == SD_SEND_CSD) {
> > > + {
> > > + UINT32 Buf[4];
> > > + ZeroMem (Buf, sizeof (Buf));
> > > + CopyMem (
> > > + (UINT8 *)Buf,
> > > + (UINT8 *)&Packet->SdMmcStatusBlk->Resp0 + 1,
> > > + sizeof (Buf) - 1
> > > + );
> > > + CopyMem (
> > > + (UINT8 *)&Packet->SdMmcStatusBlk->Resp0,
> > > + (UINT8 *)Buf,
> > > + sizeof (Buf) - 1
> > > + );
> > > + }
> > > + }
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Execute the specified TRB.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > + @retval EFI_SUCCESS The TRB is sent to host controller successfully.
> > > + @retval Others Some erros happen when sending this request to
> > the
> > > + host controller.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcExecTrb (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + EFI_STATUS Status = EFI_SUCCESS;
> > > + UINT32 Slot;
> > > +
> > > + Slot = Trb->Slot;
> > > + if (Private->Slot[Slot].CardType == EmmcCardType) {
> > > + Status = DwEmmcExecTrb (Private, Trb);
> > > + } else if (Private->Slot[Slot].CardType == SdCardType) {
> > > + Status = DwSdExecTrb (Private, Trb);
> > > + } else {
> > > + ASSERT (0);
> > > + }
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Check the TRB execution result.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > + @retval EFI_SUCCESS The TRB is executed successfully.
> > > + @retval EFI_NOT_READY The TRB is not completed for execution.
> > > + @retval Others Some erros happen when executing this request.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcCheckTrbResult (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet;
> > > + UINT32 Idsts;
> > > + UINTN DevBase;
> > > +
> > > + DevBase = Private->DevBase;
> > > + Packet = Trb->Packet;
> > > + if (Trb->UseFifo == TRUE) {
> > > + return EFI_SUCCESS;
> > > + }
> > > + if (Packet->InTransferLength) {
> > > + do {
> > > + Idsts = MmioRead32 (DevBase + DW_MMC_IDSTS);
> > > + } while ((Idsts & BIT1) == 0);
> > > + } else if (Packet->OutTransferLength) {
> > > + do {
> > > + Idsts = MmioRead32 (DevBase + DW_MMC_IDSTS);
> > > + } while ((Idsts & BIT0) == 0);
> > > + } else {
> > > + return EFI_SUCCESS;
> > > + }
> > > + Idsts = ~0;
> > > + MmioWrite32 (DevBase + DW_MMC_IDSTS, Idsts);
> > > +
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Wait for the TRB execution result.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > + @param[in] Trb The pointer to the DW_MMC_HC_TRB instance.
> > > +
> > > + @retval EFI_SUCCESS The TRB is executed successfully.
> > > + @retval Others Some erros happen when executing this request.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +DwMmcWaitTrbResult (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private,
> > > + IN DW_MMC_HC_TRB *Trb
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET *Packet;
> > > + UINT64 Timeout;
> > > + BOOLEAN InfiniteWait;
> > > +
> > > + Packet = Trb->Packet;
> > > + //
> > > + // Wait Command Complete Interrupt Status bit in Normal Interrupt
> > Status
> > > + // Register
> > > + //
> > > + Timeout = Packet->Timeout;
> > > + if (Timeout == 0) {
> > > + InfiniteWait = TRUE;
> > > + } else {
> > > + InfiniteWait = FALSE;
> > > + }
> > > +
> > > + while (InfiniteWait || (Timeout > 0)) {
> > > + //
> > > + // Check Trb execution result by reading Normal Interrupt Status
> > register.
> > > + //
> > > + Status = DwMmcCheckTrbResult (Private, Trb);
> > > + if (Status != EFI_NOT_READY) {
> > > + return Status;
> > > + }
> > > + //
> > > + // Stall for 1 microsecond.
> > > + //
> > > + gBS->Stall (1);
> > > +
> > > + Timeout--;
> > > + }
> > > +
> > > + return EFI_TIMEOUT;
> > > +}
> > > diff --git a/EmbeddedPkg/Drivers/DwMmcHcDxe/EmmcDevice.c
> > b/EmbeddedPkg/Drivers/DwMmcHcDxe/EmmcDevice.c
> > > new file mode 100644
> > > index 000000000000..b7a8688c4d2e
> > > --- /dev/null
> > > +++ b/EmbeddedPkg/Drivers/DwMmcHcDxe/EmmcDevice.c
> > > @@ -0,0 +1,1042 @@
> > > +/** @file
> > > + This file provides some helper functions which are specific for EMMC
> > device.
> > > +
> > > + Copyright (c) 2015 - 2021, Intel Corporation. All rights reserved.<BR>
> > > + Copyright (c) 2018, Linaro. All rights reserved.<BR>
> > > +
> > > + This program and the accompanying materials are licensed and made
> > available
> > > + under the terms and conditions of the BSD License which accompanies
> > this
> > > + distribution. The full text of the license may be found at
> > > + http://opensource.org/licenses/bsd-license.php
> > > +
> > > + THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS"
> > BASIS,
> > > + WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER
> > EXPRESS OR IMPLIED.
> > > +
> > > +**/
> > > +
> > > +#include <IndustryStandard/Emmc.h>
> > > +
> > > +#include <Library/BaseMemoryLib.h>
> > > +#include <Library/DebugLib.h>
> > > +#include <Library/UefiBootServicesTableLib.h>
> > > +
> > > +#include "DwMmcHcDxe.h"
> > > +
> > > +#define EMMC_GET_STATE(x) (((x) >> 9) & 0xf)
> > > +#define EMMC_STATE_IDLE 0
> > > +#define EMMC_STATE_READY 1
> > > +#define EMMC_STATE_IDENT 2
> > > +#define EMMC_STATE_STBY 3
> > > +#define EMMC_STATE_TRAN 4
> > > +#define EMMC_STATE_DATA 5
> > > +#define EMMC_STATE_RCV 6
> > > +#define EMMC_STATE_PRG 7
> > > +#define EMMC_STATE_DIS 8
> > > +#define EMMC_STATE_BTST 9
> > > +#define EMMC_STATE_SLP 10
> > > +
> > > +#define EMMC_CMD1_CAPACITY_LESS_THAN_2GB 0x00FF8080 //
> > Capacity <= 2GB, byte addressing used
> > > +#define EMMC_CMD1_CAPACITY_GREATER_THAN_2GB 0x40FF8080 //
> > Capacity > 2GB, 512-byte sector addressing used
> > > +
> > > +/**
> > > + Send command GO_IDLE_STATE (CMD0 with argument of 0x00000000)
> to
> > the device to
> > > + make it go to Idle State.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Slot The slot number of the SD card to send the
> > command
> > > + to.
> > > +
> > > + @retval EFI_SUCCESS The EMMC device is reset correctly.
> > > + @retval Others The device reset fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcReset (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = EMMC_GO_IDLE_STATE;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeBc;
> > > + SdMmcCmdBlk.ResponseType = 0;
> > > + SdMmcCmdBlk.CommandArgument = 0;
> > > +
> > > + gBS->Stall (1000);
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SEND_OP_COND to the EMMC device to get the data
> of
> > the OCR
> > > + register.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in, out] Argument On input, the argument of
> SEND_OP_COND
> > is to send
> > > + to the device.
> > > + On output, the argument is the value of OCR
> > > + register.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcGetOcr (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN OUT UINT32 *Argument
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = EMMC_SEND_OP_COND;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR3;
> > > + SdMmcCmdBlk.CommandArgument = *Argument;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + if (!EFI_ERROR (Status)) {
> > > + //
> > > + // For details, refer to SD Host Controller Simplified Spec 3.0 Table 2-
> 12.
> > > + //
> > > + *Argument = SdMmcStatusBlk.Resp0;
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Broadcast command ALL_SEND_CID to the bus to ask all the EMMC
> > devices to send
> > > + the data of their CID registers.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcGetAllCid (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = EMMC_ALL_SEND_CID;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR2;
> > > + SdMmcCmdBlk.CommandArgument = 0;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SET_RELATIVE_ADDR to the EMMC device to assign a
> > Relative device
> > > + Address (RCA).
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address to be assigned.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcSetRca (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = EMMC_SET_RELATIVE_ADDR;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > + SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SEND_CSD to the EMMC device to get the data of the
> > CSD register.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.10.4 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address of selected device.
> > > + @param[out] Csd The buffer to store the content of the CSD
> > register.
> > > + Note the caller should ignore the lowest byte of
> > > + this buffer as the content of this byte is
> > > + meaningless even if the operation succeeds.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcGetCsd (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + OUT EMMC_CSD *Csd
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = EMMC_SEND_CSD;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR2;
> > > + SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + if (!EFI_ERROR (Status)) {
> > > + //
> > > + // Copy 128bit data for CSD structure.
> > > + //
> > > + CopyMem ((VOID *)Csd + 1, &SdMmcStatusBlk.Resp0, sizeof
> > (EMMC_CSD) - 1);
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SELECT_DESELECT_CARD to the EMMC device to
> > select/deselect it.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.10.4 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address of selected device.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcSelect (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = EMMC_SELECT_DESELECT_CARD;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > + SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SEND_EXT_CSD to the EMMC device to get the data of
> > the EXT_CSD
> > > + register.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.10.4 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[out] ExtCsd The buffer to store the content of the
> EXT_CSD
> > > + register.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcGetExtCsd (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + OUT EMMC_EXT_CSD *ExtCsd
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = EMMC_SEND_EXT_CSD;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAdtc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > + SdMmcCmdBlk.CommandArgument = 0x00000000;
> > > +
> > > + Packet.InDataBuffer = ExtCsd;
> > > + Packet.InTransferLength = sizeof (EMMC_EXT_CSD);
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SWITCH to the EMMC device to switch the mode of
> > operation of the
> > > + selected Device or modifies the EXT_CSD registers.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.10.4 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Access The access mode of SWTICH command.
> > > + @param[in] Index The offset of the field to be access.
> > > + @param[in] Value The value to be set to the specified field of
> > > + EXT_CSD register.
> > > + @param[in] CmdSet The value of CmdSet field of EXT_CSD register.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcSwitch (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT8 Access,
> > > + IN UINT8 Index,
> > > + IN UINT8 Value,
> > > + IN UINT8 CmdSet
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = EMMC_SWITCH;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1b;
> > > + SdMmcCmdBlk.CommandArgument = (Access << 24) | (Index << 16) |
> \
> > > + (Value << 8) | CmdSet;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SEND_STATUS to the addressed EMMC device to get
> its
> > status
> > > + register.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.10.4 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address of addressed device.
> > > + @param[out] DevStatus The returned device status.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcSendStatus (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + OUT UINT32 *DevStatus
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = EMMC_SEND_STATUS;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > + SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + if (!EFI_ERROR (Status)) {
> > > + *DevStatus = SdMmcStatusBlk.Resp0;
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SEND_TUNING_BLOCK to the EMMC device for HS200
> > optimal sampling
> > > + point detection.
> > > +
> > > + It may be sent up to 40 times until the host finishes the tuning
> > procedure.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.8 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] BusWidth The bus width to work.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcSendTuningBlk (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT8 BusWidth
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > + UINT8 TuningBlock[128];
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = EMMC_SEND_TUNING_BLOCK;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAdtc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > + SdMmcCmdBlk.CommandArgument = 0;
> > > +
> > > + Packet.InDataBuffer = TuningBlock;
> > > + if (BusWidth == 8) {
> > > + Packet.InTransferLength = sizeof (TuningBlock);
> > > + } else {
> > > + Packet.InTransferLength = 64;
> > > + }
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Tunning the clock to get HS200 optimal sampling point.
> > > +
> > > + Command SEND_TUNING_BLOCK may be sent up to 40 times until the
> > host finishes
> > > + the tuning procedure.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.8.
> > > +
> > > + @param[in] DevIo A pointer to the EFI_DEVICE_IO_PROTOCOL
> > instance.
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] BusWidth The bus width to work.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcTuningClkForHs200 (
> > > + IN UINTN DevBase,
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT8 BusWidth
> > > + )
> > > +{
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Switch the bus width to specified width.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.9.
> > > +
> > > + @param[in] DevIo A pointer to the EFI_DEVICE_IO_PROTOCOL
> > instance.
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address to be assigned.
> > > + @param[in] IsDdr If TRUE, use dual data rate data simpling
> method.
> > > + Otherwise use single data rate data simpling method.
> > > + @param[in] BusWidth The bus width to be set, it could be 4 or 8.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcSwitchBusWidth (
> > > + IN UINTN DevBase,
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + IN BOOLEAN IsDdr,
> > > + IN UINT8 BusWidth
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + UINT8 Access;
> > > + UINT8 Index;
> > > + UINT8 Value;
> > > + UINT8 CmdSet;
> > > + UINT32 DevStatus;
> > > +
> > > + //
> > > + // Write Byte, the Value field is written into the byte pointed by Index.
> > > + //
> > > + Access = 0x03;
> > > + Index = OFFSET_OF (EMMC_EXT_CSD, BusWidth);
> > > + if (BusWidth == 1) {
> > > + Value = 0;
> > > + } else {
> > > + if (BusWidth == 4) {
> > > + Value = 1;
> > > + } else if (BusWidth == 8) {
> > > + Value = 2;
> > > + } else {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + if (IsDdr) {
> > > + Value += 4;
> > > + }
> > > + }
> > > +
> > > + CmdSet = 0;
> > > + Status = EmmcSwitch (PassThru, Access, Index, Value, CmdSet);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "EmmcSwitchBusWidth: Switch to bus width %d fails with %r\n",
> > > + BusWidth,
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > +
> > > + do {
> > > + Status = EmmcSendStatus (PassThru, Rca, &DevStatus);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "EmmcSwitchBusWidth: Send status fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > + //
> > > + // Check the switch operation is really successful or not.
> > > + //
> > > + } while ((DevStatus & 0xf) == EMMC_STATE_PRG);
> > > +
> > > + Status = DwMmcHcSetBusWidth (DevBase, IsDdr, BusWidth);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Switch the clock frequency to the specified value.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.
> > > +
> > > + @param[in] DevIo A pointer to the EFI_DEVICE_IO_PROTOCOL
> > instance.
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address to be assigned.
> > > + @param[in] HsTiming The value to be written to HS_TIMING field of
> > > + EXT_CSD register.
> > > + @param[in] ClockFreq The max clock frequency to be set, the unit is
> > MHz.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcSwitchClockFreq (
> > > + IN UINTN DevBase,
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + IN UINT8 HsTiming,
> > > + IN UINT32 ClockFreq
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + UINT8 Access;
> > > + UINT8 Index;
> > > + UINT8 Value;
> > > + UINT8 CmdSet;
> > > + UINT32 DevStatus;
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > +
> > > + Private = DW_MMC_HC_PRIVATE_FROM_THIS (PassThru);
> > > + //
> > > + // Write Byte, the Value field is written into the byte pointed by Index.
> > > + //
> > > + Access = 0x03;
> > > + Index = OFFSET_OF (EMMC_EXT_CSD, HsTiming);
> > > + Value = HsTiming;
> > > + CmdSet = 0;
> > > +
> > > + Status = EmmcSwitch (PassThru, Access, Index, Value, CmdSet);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "EmmcSwitchClockFreq: Switch to hstiming %d fails with %r\n",
> > > + HsTiming,
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > +
> > > + Status = EmmcSendStatus (PassThru, Rca, &DevStatus);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "EmmcSwitchClockFreq: Send status fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > + //
> > > + // Check the switch operation is really successful or not.
> > > + //
> > > + if ((DevStatus & BIT7) != 0) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "EmmcSwitchClockFreq: The switch operation fails as DevStatus
> > 0x%08x\n",
> > > + DevStatus
> > > + ));
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > + //
> > > + // Convert the clock freq unit from MHz to KHz.
> > > + //
> > > + Status = DwMmcHcClockSupply (DevBase, ClockFreq * 1000, Private-
> > >Capability[0]);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Switch to the High Speed timing according to request.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.8.
> > > +
> > > + @param[in] DevIo A pointer to the EFI_DEVICE_IO_PROTOCOL
> > instance.
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address to be assigned.
> > > + @param[in] ClockFreq The max clock frequency to be set.
> > > + @param[in] IsDdr If TRUE, use dual data rate data simpling
> method.
> > > + Otherwise use single data rate data simpling method.
> > > + @param[in] BusWidth The bus width to be set, it could be 4 or 8.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcSwitchToHighSpeed (
> > > + IN UINTN DevBase,
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + IN UINT32 ClockFreq,
> > > + IN BOOLEAN IsDdr,
> > > + IN UINT8 BusWidth
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + UINT8 HsTiming;
> > > +
> > > + HsTiming = 1;
> > > + Status = EmmcSwitchClockFreq (DevBase, PassThru, Rca, HsTiming,
> > ClockFreq);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + Status = EmmcSwitchBusWidth (DevBase, PassThru, Rca, IsDdr,
> > BusWidth);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Switch to the HS200 timing according to request.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.8.
> > > +
> > > + @param[in] DevIo A pointer to the EFI_DEVICE_IO_PROTOCOL
> > instance.
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address to be assigned.
> > > + @param[in] ClockFreq The max clock frequency to be set.
> > > + @param[in] BusWidth The bus width to be set, it could be 4 or 8.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcSwitchToHS200 (
> > > + IN UINTN DevBase,
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + IN UINT32 ClockFreq,
> > > + IN UINT8 BusWidth
> > > + )
> > > +{
> > > + return EFI_SUCCESS;
> > > +}
> > > +
> > > +/**
> > > + Switch the high speed timing according to request.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.6.8.
> > > +
> > > + @param[in] DevIo A pointer to the EFI_DEVICE_IO_PROTOCOL
> > instance.
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address to be assigned.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcSetBusMode (
> > > + IN UINTN DevBase,
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + EMMC_CSD Csd;
> > > + EMMC_EXT_CSD ExtCsd;
> > > + UINT8 HsTiming;
> > > + BOOLEAN IsDdr;
> > > + UINT32 DevStatus;
> > > + UINT32 ClockFreq;
> > > + UINT8 BusWidth;
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > +
> > > + Private = DW_MMC_HC_PRIVATE_FROM_THIS (PassThru);
> > > + ASSERT (Private->Capability[0].BaseClkFreq != 0);
> > > +
> > > + Status = EmmcGetCsd (PassThru, Rca, &Csd);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((DEBUG_ERROR, "EmmcSetBusMode: GetCsd fails with
> %r\n",
> > Status));
> > > + return Status;
> > > + }
> > > +
> > > + Status = EmmcSelect (PassThru, Rca);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((DEBUG_ERROR, "EmmcSetBusMode: Select fails with %r\n",
> > Status));
> > > + return Status;
> > > + }
> > > +
> > > + do {
> > > + Status = EmmcSendStatus (PassThru, Rca, &DevStatus);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "EmmcSetBusMode: Get Status fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > + } while (EMMC_GET_STATE (DevStatus) != EMMC_STATE_TRAN);
> > > +
> > > + BusWidth = 1;
> > > + Status = EmmcSwitchBusWidth (DevBase, PassThru, Rca, FALSE,
> > BusWidth);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + BusWidth = Private->Capability[0].BusWidth;
> > > + //
> > > + // Get Deivce_Type from EXT_CSD register.
> > > + //
> > > + Status = EmmcGetExtCsd (PassThru, &ExtCsd);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((DEBUG_ERROR, "EmmcSetBusMode: GetExtCsd fails with
> > %r\n", Status));
> > > + return Status;
> > > + }
> > > +
> > > + //
> > > + // Calculate supported bus speed/bus width/clock frequency.
> > > + //
> > > + HsTiming = 0;
> > > + IsDdr = FALSE;
> > > + ClockFreq = 0;
> > > + if (((ExtCsd.DeviceType & (BIT4 | BIT5)) != 0) &&
> > > + (Private->Capability[0].Sdr104 != 0)) {
> > > + HsTiming = 2;
> > > + IsDdr = FALSE;
> > > + ClockFreq = 200;
> > > + } else if (((ExtCsd.DeviceType & (BIT2 | BIT3)) != 0) &&
> > > + (Private->Capability[0].Ddr50 != 0)) {
> > > + HsTiming = 1;
> > > + IsDdr = TRUE;
> > > + ClockFreq = 52;
> > > + } else if (((ExtCsd.DeviceType & BIT1) != 0) &&
> > > + (Private->Capability[0].HighSpeed != 0)) {
> > > + HsTiming = 1;
> > > + IsDdr = FALSE;
> > > + ClockFreq = 52;
> > > + } else if (((ExtCsd.DeviceType & BIT0) != 0) &&
> > > + (Private->Capability[0].HighSpeed != 0)) {
> > > + HsTiming = 1;
> > > + IsDdr = FALSE;
> > > + ClockFreq = 26;
> > > + }
> > > +
> > > + if ((ClockFreq == 0) || (HsTiming == 0)) {
> > > + //
> > > + // Continue using default setting.
> > > + //
> > > + return EFI_SUCCESS;
> > > + }
> > > +
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "EmmcSetBusMode: HsTiming %d ClockFreq %d BusWidth %d Ddr
> > %a\n",
> > > + HsTiming,
> > > + ClockFreq,
> > > + BusWidth,
> > > + IsDdr ? "TRUE" : "FALSE"
> > > + ));
> > > +
> > > + if (HsTiming == 2) {
> > > + //
> > > + // Execute HS200 timing switch procedure
> > > + //
> > > + Status = EmmcSwitchToHS200 (DevBase, PassThru, Rca, ClockFreq,
> > BusWidth);
> > > + } else {
> > > + //
> > > + // Execute High Speed timing switch procedure
> > > + //
> > > + Status = EmmcSwitchToHighSpeed (
> > > + DevBase,
> > > + PassThru,
> > > + Rca,
> > > + ClockFreq,
> > > + IsDdr,
> > > + BusWidth
> > > + );
> > > + }
> > > +
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "EmmcSetBusMode: Switch to %a %r\n",
> > > + (HsTiming == 3) ? "HS400" : ((HsTiming == 2) ? "HS200" : "HighSpeed"),
> > > + Status
> > > + ));
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Execute EMMC device identification procedure.
> > > +
> > > + Refer to EMMC Electrical Standard Spec 5.1 Section 6.4 for details.
> > > +
> > > + @param[in] Private A pointer to the DW_MMC_HC_PRIVATE_DATA
> > instance.
> > > +
> > > + @retval EFI_SUCCESS There is a EMMC card.
> > > + @retval Others There is not a EMMC card.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +EmmcIdentification (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + UINTN DevBase;
> > > + EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru;
> > > + UINT32 Ocr;
> > > + UINT16 Rca;
> > > + UINT32 DevStatus;
> > > + UINT32 Timeout;
> > > +
> > > + DevBase = Private->DevBase;
> > > + PassThru = &Private->PassThru;
> > > +
> > > + Status = EmmcReset (PassThru);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "EmmcIdentification: Executing Cmd0 fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > +
> > > + Timeout = 100;
> > > + do {
> > > + Ocr = EMMC_CMD1_CAPACITY_GREATER_THAN_2GB;
> > > + Status = EmmcGetOcr (PassThru, &Ocr);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "EmmcIdentification: Executing Cmd1 fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > + if (--Timeout <= 0) {
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > + MicroSecondDelay (100);
> > > + } while ((Ocr & BIT31) == 0);
> > > +
> > > + Status = EmmcGetAllCid (PassThru);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "EmmcIdentification: Executing Cmd2 fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > + //
> > > + // valid RCA starts from 1.
> > > + // Here we takes a simple formula to calculate the RCA.
> > > + // Don't support multiple devices on the slot, that is
> > > + // shared bus slot feature.
> > > + //
> > > + Rca = 1;
> > > + Status = EmmcSetRca (PassThru, Rca);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "EmmcIdentification: Executing Cmd3 fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > + //
> > > + // Enter Data Tranfer Mode.
> > > + //
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "EmmcIdentification: Found a EMMC device at RCA [%d]\n",
> > > + Rca
> > > + ));
> > > + Private->Slot[0].CardType = EmmcCardType;
> > > +
> > > + Status = EmmcSetBusMode (DevBase, PassThru, Rca);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + //
> > > + // Exit DATA Mode.
> > > + //
> > > + do {
> > > + Status = EmmcSendStatus (PassThru, Rca, &DevStatus);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "EmmcSwitchBusWidth: Send status fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > + } while ((DevStatus & 0xf) == EMMC_STATE_DATA);
> > > +
> > > + return Status;
> > > +}
> > > diff --git a/EmbeddedPkg/Drivers/DwMmcHcDxe/SdDevice.c
> > b/EmbeddedPkg/Drivers/DwMmcHcDxe/SdDevice.c
> > > new file mode 100644
> > > index 000000000000..63246637b6dd
> > > --- /dev/null
> > > +++ b/EmbeddedPkg/Drivers/DwMmcHcDxe/SdDevice.c
> > > @@ -0,0 +1,1105 @@
> > > +/** @file
> > > + This file provides some helper functions which are specific for SD card
> > > + device.
> > > +
> > > + Copyright (c) 2015 - 2021, Intel Corporation. All rights reserved.<BR>
> > > + Copyright (c) 2018, Linaro. All rights reserved.<BR>
> > > +
> > > + This program and the accompanying materials are licensed and made
> > available
> > > + under the terms and conditions of the BSD License which accompanies
> > this
> > > + distribution. The full text of the license may be found at
> > > + http://opensource.org/licenses/bsd-license.php
> > > +
> > > + THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS"
> > BASIS,
> > > + WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER
> > EXPRESS OR IMPLIED.
> > > +
> > > +**/
> > > +
> > > +#include <IndustryStandard/Sd.h>
> > > +
> > > +#include <Library/BaseMemoryLib.h>
> > > +#include <Library/DebugLib.h>
> > > +
> > > +#include "DwMmcHcDxe.h"
> > > +
> > > +/**
> > > + Send command GO_IDLE_STATE to the device to make it go to Idle
> State.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > +
> > > + @retval EFI_SUCCESS The SD device is reset correctly.
> > > + @retval Others The device reset fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardReset (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_GO_IDLE_STATE;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeBc;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + //Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SEND_IF_COND to the device to inquiry the SD
> Memory
> > Card
> > > + interface condition.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] SupplyVoltage The supplied voltage by the host.
> > > + @param[in] CheckPattern The check pattern to be sent to the device.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardVoltageCheck (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT8 SupplyVoltage,
> > > + IN UINT8 CheckPattern
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_SEND_IF_COND;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR7;
> > > + SdMmcCmdBlk.CommandArgument = (SupplyVoltage << 8) |
> > CheckPattern;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + if (!EFI_ERROR (Status)) {
> > > + if (SdMmcStatusBlk.Resp0 != SdMmcCmdBlk.CommandArgument) {
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SDIO_SEND_OP_COND to the device to see whether it
> is
> > SDIO device.
> > > +
> > > + Refer to SDIO Simplified Spec 3 Section 3.2 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] VoltageWindow The supply voltage window.
> > > + @param[in] S18R The boolean to show if it should switch to 1.8v.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdioSendOpCond (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT32 VoltageWindow,
> > > + IN BOOLEAN S18R
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > + UINT32 Switch;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SDIO_SEND_OP_COND;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR4;
> > > +
> > > + Switch = S18R ? BIT24 : 0;
> > > +
> > > + SdMmcCmdBlk.CommandArgument = (VoltageWindow & 0xFFFFFF) |
> > Switch;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SD_SEND_OP_COND to the device to see whether it is
> > SDIO device.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address of addressed device.
> > > + @param[in] VoltageWindow The supply voltage window.
> > > + @param[in] S18R The boolean to show if it should switch to 1.8v.
> > > + @param[in] Xpc The boolean to show if it should provide 0.36w
> > > + power control.
> > > + @param[in] Hcs The boolean to show if it support host capacity
> > > + info.
> > > + @param[out] Ocr The buffer to store returned OCR register
> value.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardSendOpCond (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + IN UINT32 VoltageWindow,
> > > + IN BOOLEAN S18R,
> > > + IN BOOLEAN Xpc,
> > > + IN BOOLEAN Hcs,
> > > + OUT UINT32 *Ocr
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > + UINT32 Switch;
> > > + UINT32 MaxPower;
> > > + UINT32 HostCapacity;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_APP_CMD;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > + SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_SEND_OP_COND;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR3;
> > > +
> > > + Switch = S18R ? BIT24 : 0;
> > > + MaxPower = Xpc ? BIT28 : 0;
> > > + HostCapacity = Hcs ? BIT30 : 0;
> > > +
> > > + SdMmcCmdBlk.CommandArgument = (VoltageWindow & 0xFFFFFF) |
> > Switch | \
> > > + MaxPower | HostCapacity;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + if (!EFI_ERROR (Status)) {
> > > + *Ocr = SdMmcStatusBlk.Resp0;
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Broadcast command ALL_SEND_CID to the bus to ask all the SD devices
> > to send
> > > + the data of their CID registers.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardAllSendCid (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_ALL_SEND_CID;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR2;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SET_RELATIVE_ADDR to the SD device to assign a
> > Relative device
> > > + Address (RCA).
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[out] Rca The relative device address to assign.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardSetRca (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + OUT UINT16 *Rca
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_SET_RELATIVE_ADDR;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR6;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + if (!EFI_ERROR (Status)) {
> > > + *Rca = (UINT16)(SdMmcStatusBlk.Resp0 >> 16);
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SEND_CSD to the SD device to get the data of the CSD
> > register.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address of selected device.
> > > + @param[out] Csd The buffer to store the content of the CSD
> > register.
> > > + Note the caller should ignore the lowest byte of
> > > + this buffer as the content of this byte is meaning-
> > > + less even if the operation succeeds.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardGetCsd (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + OUT SD_CSD *Csd
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_SEND_CSD;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR2;
> > > + SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + if (!EFI_ERROR (Status)) {
> > > + CopyMem (((UINT8*)Csd) + 1, &SdMmcStatusBlk.Resp0, sizeof
> > (SD_CSD) - 1);
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SEND_CSD to the SD device to get the data of the CSD
> > register.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address of selected device.
> > > + @param[out] Scr The buffer to store the content of the SCR
> > register.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardGetScr (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + OUT SD_SCR *Scr
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_APP_CMD;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > + SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_SEND_SCR;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAdtc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > +
> > > + Packet.InDataBuffer = Scr;
> > > + Packet.InTransferLength = sizeof (SD_SCR);
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SELECT_DESELECT_CARD to the SD device to
> > select/deselect it.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address of selected device.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardSelect (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_SELECT_DESELECT_CARD;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + if (Rca != 0) {
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1b;
> > > + }
> > > + SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command VOLTAGE_SWITCH to the SD device to switch the
> voltage
> > of the
> > > + device.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardVoltageSwitch (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_VOLTAGE_SWITCH;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > + SdMmcCmdBlk.CommandArgument = 0;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SET_BUS_WIDTH to the SD device to set the bus width.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address of addressed device.
> > > + @param[in] BusWidth The bus width to be set, it could be 1 or 4.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardSetBusWidth (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + IN UINT8 BusWidth
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > + UINT8 Value;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_APP_CMD;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > + SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_SET_BUS_WIDTH;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > +
> > > + if (BusWidth == 1) {
> > > + Value = 0;
> > > + } else if (BusWidth == 4) {
> > > + Value = 2;
> > > + } else {
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + SdMmcCmdBlk.CommandArgument = Value & 0x3;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SWITCH_FUNC to the SD device to check switchable
> > function or
> > > + switch card function.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] AccessMode The value for access mode group.
> > > + @param[in] CommandSystem The value for command set group.
> > > + @param[in] DriveStrength The value for drive length group.
> > > + @param[in] PowerLimit The value for power limit group.
> > > + @param[in] Mode Switch or check function.
> > > + @param[out] SwitchResp The return switch function status.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardSwitch (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT8 AccessMode,
> > > + IN UINT8 CommandSystem,
> > > + IN UINT8 DriveStrength,
> > > + IN UINT8 PowerLimit,
> > > + IN BOOLEAN Mode,
> > > + OUT UINT8 *SwitchResp
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > + UINT32 ModeValue;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_SWITCH_FUNC;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAdtc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > +
> > > + ModeValue = Mode ? BIT31 : 0;
> > > + SdMmcCmdBlk.CommandArgument = (AccessMode & 0xF) | \
> > > + ((PowerLimit & 0xF) << 4) | \
> > > + ((DriveStrength & 0xF) << 8) | \
> > > + ((DriveStrength & 0xF) << 12) | \
> > > + ModeValue;
> > > +
> > > + Packet.InDataBuffer = SwitchResp;
> > > + Packet.InTransferLength = 64;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SEND_STATUS to the addressed SD device to get its
> > status
> > > + register.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address of addressed device.
> > > + @param[out] DevStatus The returned device status.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardSendStatus (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + OUT UINT32 *DevStatus
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_SEND_STATUS;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > + SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > + if (!EFI_ERROR (Status)) {
> > > + *DevStatus = SdMmcStatusBlk.Resp0;
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Send command SEND_TUNING_BLOCK to the SD device for HS200
> > optimal sampling
> > > + point detection.
> > > +
> > > + It may be sent up to 40 times until the host finishes the tuning
> > procedure.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardSendTuningBlk (
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru
> > > + )
> > > +{
> > > + EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
> > > + EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
> > > + EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
> > > + EFI_STATUS Status;
> > > + UINT8 TuningBlock[64];
> > > +
> > > + ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
> > > + ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
> > > + ZeroMem (&Packet, sizeof (Packet));
> > > +
> > > + Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
> > > + Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
> > > + Packet.Timeout = DW_MMC_HC_GENERIC_TIMEOUT;
> > > +
> > > + SdMmcCmdBlk.CommandIndex = SD_SEND_TUNING_BLOCK;
> > > + SdMmcCmdBlk.CommandType = SdMmcCommandTypeAdtc;
> > > + SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
> > > + SdMmcCmdBlk.CommandArgument = 0;
> > > +
> > > + Packet.InDataBuffer = TuningBlock;
> > > + Packet.InTransferLength = sizeof (TuningBlock);
> > > +
> > > + Status = PassThru->PassThru (PassThru, 0, &Packet, NULL);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Switch the bus width to specified width.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 and
> > > + SD Host Controller Simplified Spec 3.0 section Figure 3-7 for details.
> > > +
> > > + @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL
> instance.
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address to be assigned.
> > > + @param[in] BusWidth The bus width to be set, it could be 4 or 8.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardSwitchBusWidth (
> > > + IN UINTN DevBase,
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + IN BOOLEAN IsDdr,
> > > + IN UINT8 BusWidth
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + UINT32 DevStatus;
> > > +
> > > + Status = SdCardSetBusWidth (PassThru, Rca, BusWidth);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardSwitchBusWidth: Switch to bus width %d fails with %r\n",
> > > + BusWidth,
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > +
> > > + Status = SdCardSendStatus (PassThru, Rca, &DevStatus);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardSwitchBusWidth: Send status fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > + //
> > > + // Check the switch operation is really successful or not.
> > > + //
> > > + if ((DevStatus >> 16) != 0) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardSwitchBusWidth: The switch operation fails as DevStatus
> > 0x%08x\n",
> > > + DevStatus
> > > + ));
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > +
> > > + Status = DwMmcHcSetBusWidth (DevBase, IsDdr, BusWidth);
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +/**
> > > + Switch the high speed timing according to request.
> > > +
> > > + Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
> > > +
> > > + @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL
> instance.
> > > + @param[in] PassThru A pointer to the
> > EFI_SD_MMC_PASS_THRU_PROTOCOL
> > > + instance.
> > > + @param[in] Rca The relative device address to be assigned.
> > > + @param[in] S18A The boolean to show if it's a UHS-I SD card.
> > > + @param[in] BusWidths The bus width of the SD card.
> > > +
> > > + @retval EFI_SUCCESS The operation is done correctly.
> > > + @retval Others The operation fails.
> > > +
> > > +**/
> > > +EFI_STATUS
> > > +SdCardSetBusMode (
> > > + IN UINTN DevBase,
> > > + IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
> > > + IN UINT16 Rca,
> > > + IN BOOLEAN S18A,
> > > + IN UINT32 BusWidths
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + DW_MMC_HC_SLOT_CAP *Capability;
> > > + UINT32 ClockFreq;
> > > + UINT8 AccessMode;
> > > + UINT8 SwitchResp[64];
> > > + DW_MMC_HC_PRIVATE_DATA *Private;
> > > + BOOLEAN IsDdr;
> > > +
> > > + Private = DW_MMC_HC_PRIVATE_FROM_THIS (PassThru);
> > > +
> > > + Capability = &Private->Capability[0];
> > > +
> > > + if ((Capability->BusWidth == 1) || (Capability->BusWidth == 4)) {
> > > + BusWidths &= Capability[0].BusWidth;
> > > + } else {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardSetBusMode: BusWidths (%d) in capability are wrong\n",
> > > + Capability->BusWidth
> > > + ));
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + if (BusWidths == 0) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardSetBusMode: Get wrong BusWidths:%d\n",
> > > + BusWidths
> > > + ));
> > > + return EFI_INVALID_PARAMETER;
> > > + }
> > > +
> > > + if (Private->Capability[0].Ddr50) {
> > > + IsDdr = TRUE;
> > > + } else {
> > > + IsDdr = FALSE;
> > > + }
> > > +
> > > + Status = SdCardSwitchBusWidth (DevBase, PassThru, Rca, IsDdr,
> > BusWidths);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardSetBusMode: Executing SdCardSwitchBusWidth fails with
> > %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > +
> > > + //
> > > + // Get the supported bus speed from SWITCH cmd return data group
> #1.
> > > + //
> > > + Status = SdCardSwitch (PassThru, 0xF, 0xF, 0xF, 0xF, FALSE,
> SwitchResp);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > + //
> > > + // Calculate supported bus speed/bus width/clock frequency by host
> and
> > device
> > > + // capability.
> > > + //
> > > + ClockFreq = 0;
> > > + if (S18A && (Capability->Sdr104 != 0) && ((SwitchResp[13] & BIT3) != 0))
> {
> > > + ClockFreq = 208;
> > > + AccessMode = 3;
> > > + } else if (S18A && (Capability->Sdr50 != 0) &&
> > > + ((SwitchResp[13] & BIT2) != 0)) {
> > > + ClockFreq = 100;
> > > + AccessMode = 2;
> > > + } else if (S18A && (Capability->Ddr50 != 0) &&
> > > + ((SwitchResp[13] & BIT4) != 0)) {
> > > + ClockFreq = 50;
> > > + AccessMode = 4;
> > > + } else if ((SwitchResp[13] & BIT1) != 0) {
> > > + ClockFreq = 50;
> > > + AccessMode = 1;
> > > + } else {
> > > + ClockFreq = 25;
> > > + AccessMode = 0;
> > > + }
> > > +
> > > + Status = SdCardSwitch (PassThru, AccessMode, 0xF, 0xF, 0xF, TRUE,
> > SwitchResp);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + if ((SwitchResp[16] & 0xF) != AccessMode) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardSetBusMode: Switch to AccessMode %d ClockFreq %d fails!
> > The Switch response is 0x%1x\n",
> > > + AccessMode,
> > > + ClockFreq,
> > > + SwitchResp[16] & 0xF
> > > + ));
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > +
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "SdCardSetBusMode: Switch to AccessMode %d ClockFreq %d \n",
> > > + AccessMode,
> > > + ClockFreq
> > > + ));
> > > +
> > > + Status = DwMmcHcClockSupply (DevBase, ClockFreq * 1000,
> *Capability);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + return Status;
> > > +}
> > > +
> > > +EFI_STATUS
> > > +SdCardIdentification (
> > > + IN DW_MMC_HC_PRIVATE_DATA *Private
> > > + )
> > > +{
> > > + EFI_STATUS Status;
> > > + UINTN DevBase;
> > > + EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru;
> > > + UINT32 Ocr;
> > > + UINT16 Rca;
> > > + BOOLEAN Xpc;
> > > + BOOLEAN S18r;
> > > + UINT64 MaxCurrent;
> > > + SD_SCR Scr;
> > > + SD_CSD Csd;
> > > +
> > > + DevBase = Private->DevBase;
> > > + PassThru = &Private->PassThru;
> > > + //
> > > + // 1. Send Cmd0 to the device
> > > + //
> > > + Status = SdCardReset (PassThru);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "SdCardIdentification: Executing Cmd0 fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > + MicroSecondDelay (10000);
> > > + //
> > > + // 2. Send Cmd8 to the device
> > > + //
> > > + Status = SdCardVoltageCheck (PassThru, 0x1, 0xFF);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "SdCardIdentification: Executing Cmd8 fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > + //
> > > + // 3. Send Acmd41 with voltage window 0 to the device
> > > + //
> > > + Status = SdCardSendOpCond (PassThru, 0, 0, FALSE, FALSE, FALSE,
> &Ocr);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_INFO,
> > > + "SdCardIdentification: Executing SdCardSendOpCond fails with
> %r\n",
> > > + Status
> > > + ));
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > +
> > > + if (Private->Capability[0].Voltage33 != 0) {
> > > + //
> > > + // Support 3.3V
> > > + //
> > > + MaxCurrent = ((UINT32)Private->MaxCurrent[0] & 0xFF) * 4;
> > > + S18r = FALSE;
> > > + } else if (Private->Capability[0].Voltage30 != 0) {
> > > + //
> > > + // Support 3.0V
> > > + //
> > > + MaxCurrent = (((UINT32)Private->MaxCurrent[0] >> 8) & 0xFF) * 4;
> > > + S18r = FALSE;
> > > + } else if (Private->Capability[0].Voltage18 != 0) {
> > > + //
> > > + // Support 1.8V
> > > + //
> > > + MaxCurrent = (((UINT32)Private->MaxCurrent[0] >> 16) & 0xFF) * 4;
> > > + S18r = TRUE;
> > > + } else {
> > > + ASSERT (FALSE);
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > +
> > > + if (MaxCurrent >= 150) {
> > > + Xpc = TRUE;
> > > + } else {
> > > + Xpc = FALSE;
> > > + }
> > > +
> > > + //
> > > + // 4. Repeatly send Acmd41 with supply voltage window to the device.
> > > + // Note here we only support the cards complied with SD physical
> > > + // layer simplified spec version 2.0 and version 3.0 and above.
> > > + //
> > > + do {
> > > + Status = SdCardSendOpCond (PassThru, 0, Ocr, S18r, Xpc, TRUE,
> &Ocr);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardIdentification: SdCardSendOpCond fails with %r Ocr %x, S18r
> > %x, Xpc %x\n",
> > > + Status,
> > > + Ocr,
> > > + S18r,
> > > + Xpc
> > > + ));
> > > + return EFI_DEVICE_ERROR;
> > > + }
> > > + } while ((Ocr & BIT31) == 0);
> > > +
> > > + Status = SdCardAllSendCid (PassThru);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardIdentification: Executing SdCardAllSendCid fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > +
> > > + Status = SdCardSetRca (PassThru, &Rca);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardIdentification: Executing SdCardSetRca fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > +
> > > + Status = SdCardGetCsd (PassThru, Rca, &Csd);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardIdentification: Executing SdCardGetCsd fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > +
> > > + Status = SdCardSelect (PassThru, Rca);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardIdentification: Selecting card fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > +
> > > + Status = SdCardGetScr (PassThru, Rca, &Scr);
> > > + if (EFI_ERROR (Status)) {
> > > + DEBUG ((
> > > + DEBUG_ERROR,
> > > + "SdCardIdentification: Executing SdCardGetScr fails with %r\n",
> > > + Status
> > > + ));
> > > + return Status;
> > > + }
> > > +
> > > + //
> > > + // Enter Data Tranfer Mode.
> > > + //
> > > + DEBUG ((DEBUG_INFO, "SdCardIdentification: Found a SD device\n"));
> > > + Private->Slot[0].CardType = SdCardType;
> > > +
> > > + Status = SdCardSetBusMode (DevBase, PassThru, Rca, S18r,
> > Scr.SdBusWidths);
> > > + if (EFI_ERROR (Status)) {
> > > + return Status;
> > > + }
> > > +
> > > + Private->Slot[0].Initialized = TRUE;
> > > +
> > > + return Status;
> > > +}
> > > --
> > > 2.12.3
next prev parent reply other threads:[~2021-04-27 10:28 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20210322032439.9312-1-tien.hock.loh@intel.com>
2021-03-22 3:24 ` [PATCH V5 1/1] EmbeddedPkg: DwMmcHcDxe: Add support for Designware SDMMC driver Loh, Tien Hock
2021-03-30 4:36 ` Loh, Tien Hock
2021-04-16 5:34 ` Loh, Tien Hock
2021-04-26 17:53 ` Michael D Kinney
2021-04-27 9:08 ` Loh, Tien Hock
2021-04-27 10:27 ` Loh, Tien Hock [this message]
2021-04-27 17:31 ` [edk2-devel] " Andrew Fish
2021-04-27 19:31 ` Michael D Kinney
2021-04-28 13:03 ` Ard Biesheuvel
2021-04-28 14:58 ` Andrew Fish
2021-04-29 0:33 ` Loh, Tien Hock
2021-04-27 21:40 ` Michael Brown
2021-04-27 23:45 ` Andrew Fish
2021-04-28 0:06 ` Michael D Kinney
2021-04-28 0:52 ` Andrew Fish
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-list from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=SJ0PR11MB513626B13059C47EC64D9C89BD419@SJ0PR11MB5136.namprd11.prod.outlook.com \
--to=devel@edk2.groups.io \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox