Re: [PATCH v1 1/1] ArmPkg/ArmGicDxe: fix writes to GICD_IPRIORITYR<n> when ARE enable

["Ard Biesheuvel" <ard.biesheuvel@arm.com>]

On 10/28/20 2:21 AM, Quan Nguyen wrote:
> According to ARM doc IHI 0069F, section 11.9.18, "Accessing the
> GICD_IPRIORITYR<n>:", "These registers are always used when affinity
> routing is not enabled. When affinity routing is enabled for the
> Security state of an interrupt:
>   * GICR_IPRIORITYR<n> is used instead of GICD_IPRIORITYR<n> where n = 0
> to 7 (that is, for SGIs and PPIs)."
> 
> The current ArmGicV3 code tries to initialize all the IPRIORITYR
> registers to a default state via the Distributor (GICD), so skip
> writes to the first eight IPRIORITYR registers when Affinity Routing
> is Enabled.
> 
> Cc: Leif Lindholm <leif@nuviainc.com>
> Cc: Ard Biesheuvel <ard.biesheuvel@arm.com>
> Signed-off-by: Victor Gallardo <Victor@os.amperecomputing.com>
> Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>

Isn't this already being taken into account in ArmGicDisableInterrupt()?

> ---
>   ArmPkg/Drivers/ArmGic/GicV3/ArmGicV3Dxe.c | 11 +++++++++++
>   1 file changed, 11 insertions(+)
> 
> diff --git a/ArmPkg/Drivers/ArmGic/GicV3/ArmGicV3Dxe.c b/ArmPkg/Drivers/ArmGic/GicV3/ArmGicV3Dxe.c
> index d7da1f198d9e..bc543502481b 100644
> --- a/ArmPkg/Drivers/ArmGic/GicV3/ArmGicV3Dxe.c
> +++ b/ArmPkg/Drivers/ArmGic/GicV3/ArmGicV3Dxe.c
> @@ -378,6 +378,7 @@ GicV3DxeInitialize (
>     UINTN                   RegShift;
>     UINT64                  CpuTarget;
>     UINT64                  MpId;
> +  BOOLEAN                 AffinityRoutingEnabled = FALSE;
>   
>     // Make sure the Interrupt Controller Protocol is not already installed in
>     // the system.
> @@ -391,11 +392,21 @@ GicV3DxeInitialize (
>     // Routing enabled. So ensure that the ARE bit is set.
>     if (!FeaturePcdGet (PcdArmGicV3WithV2Legacy)) {
>       MmioOr32 (mGicDistributorBase + ARM_GIC_ICDDCR, ARM_GIC_ICDDCR_ARE);
> +    // If Affinity Routing is Enabled, the first 32 interrupts (SGI and PPI)
> +    // can be programmed only through Redistributor interface (GICR).
> +    // Initializing the GICD_IPRIORITYR registers for these interrupts can be
> +    // skipped as the Redistributor will be powered up and initialized
> +    // at the appropriate time (e.g. in EL3 by trusted firmware).
> +    AffinityRoutingEnabled = TRUE;
>     }
>   
>     for (Index = 0; Index < mGicNumInterrupts; Index++) {
>       GicV3DisableInterruptSource (&gHardwareInterruptV3Protocol, Index);
>   
> +    if (AffinityRoutingEnabled && Index < 32) {
> +      continue;
> +    }
> +
>       // Set Priority
>       RegOffset = Index / 4;
>       RegShift = (Index % 4) * 8;
>