[Patch][edk2-platforms/devel-MinnowBoard3] Add SATA initialization.

[Patch][edk2-platforms/devel-MinnowBoard3] Add SATA initialization.

[lushifex]

Add additional SATA initialization code.

Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: lushifex <shifeix.a.lu@intel.com>
---
 .../BroxtonSiPkg/SouthCluster/ScInit/Dxe/ScInit.c  |  3 +
 .../BroxtonSiPkg/SouthCluster/ScInit/Dxe/ScSata.c  | 91 +++++++++++++++++++++-
 2 files changed, 93 insertions(+), 1 deletion(-)

diff --git a/Silicon/BroxtonSoC/BroxtonSiPkg/SouthCluster/ScInit/Dxe/ScInit.c b/Silicon/BroxtonSoC/BroxtonSiPkg/SouthCluster/ScInit/Dxe/ScInit.c
index 9620dac..3fb37ea 100644
--- a/Silicon/BroxtonSoC/BroxtonSiPkg/SouthCluster/ScInit/Dxe/ScInit.c
+++ b/Silicon/BroxtonSoC/BroxtonSiPkg/SouthCluster/ScInit/Dxe/ScInit.c
@@ -660,6 +660,9 @@ ScOnEndOfDxe (
   gBS->CloseEvent (Event);
 
   BxtSeries = GetBxtSeries ();
+  if (BxtSeries == BxtP) {
+    ConfigureSataDxe (mScPolicy);
+  }
   AcpiBaseAddr   = (UINT16) PcdGet16 (PcdScAcpiIoPortBaseAddress);
   PmcBase        = PMC_BASE_ADDRESS;
   FuncDisableReg = MmioRead32 (PmcBase + R_PMC_FUNC_DIS);
diff --git a/Silicon/BroxtonSoC/BroxtonSiPkg/SouthCluster/ScInit/Dxe/ScSata.c b/Silicon/BroxtonSoC/BroxtonSiPkg/SouthCluster/ScInit/Dxe/ScSata.c
index 63c2b88..c6d83e9 100644
--- a/Silicon/BroxtonSoC/BroxtonSiPkg/SouthCluster/ScInit/Dxe/ScSata.c
+++ b/Silicon/BroxtonSoC/BroxtonSiPkg/SouthCluster/ScInit/Dxe/ScSata.c
@@ -1,7 +1,7 @@
 /** @file
   Perform related functions for SC Sata in DXE phase.
 
-  Copyright (c) 2014 - 2016, Intel Corporation. All rights reserved.<BR>
+  Copyright (c) 2014 - 2017, Intel Corporation. All rights reserved.<BR>
 
   This program and the accompanying materials
   are licensed and made available under the terms and conditions of the BSD License
@@ -15,4 +15,93 @@
 
 #include <ScInit.h>
 
+/**
+  Perform the remaining configuration on SC SATA to perform device detection
+  at end of Dxe, then set the SATA SPD and PxE corresponding, and set the Register Lock
+
+  @param[in] ScPolicy                   The SC Policy instance
+
+  @retval    EFI_SUCCESS                The function completed successfully
+
+**/
+EFI_STATUS
+ConfigureSataDxe (
+  IN SC_POLICY_HOB     *ScPolicy
+  )
+{
+  EFI_STATUS     Status;
+  SC_SATA_CONFIG *SataConfig;
+  UINTN          PciSataRegBase;
+  UINT16         SataPortsEnabled;
+  UINT32         DwordReg;
+  UINTN          Index;
+
+  DEBUG ((DEBUG_INFO, "ConfigureSataDxe() Start\n"));
+  Status = GetConfigBlock ((VOID *) ScPolicy, &gSataConfigGuid, (VOID *) &SataConfig);
+  ASSERT_EFI_ERROR (Status);
+
+  //
+  // SATA PCS: Enable the port in any of below condition:
+  // i.)   Hot plug is enabled
+  // ii.)  A device is attached
+  // iii.) Test mode is enabled
+  // iv.)  Configured as eSATA port
+  //
+  PciSataRegBase = MmPciBase (
+                     DEFAULT_PCI_BUS_NUMBER_SC,
+                     PCI_DEVICE_NUMBER_SATA,
+                     PCI_FUNCTION_NUMBER_SATA
+                     );
+  SataPortsEnabled = 0;
+  DwordReg = MmioRead32 (PciSataRegBase + 0x94);
+  DEBUG ((DEBUG_INFO, "PCS = 0x%x\n", DwordReg));
+  for (Index = 0; Index < SC_MAX_SATA_PORTS; Index++) {
+    if ((SataConfig->PortSettings[Index].HotPlug == TRUE) ||
+        (DwordReg & (BIT16 << Index)) ||
+        (SataConfig->TestMode == TRUE) ||
+        (SataConfig->PortSettings[Index].External == TRUE)) {
+      SataPortsEnabled |= (SataConfig->PortSettings[Index].Enable << Index);
+    }
+  }
+  DEBUG ((DEBUG_INFO, "SataPortsEnabled = 0x%x\n", SataPortsEnabled));
+
+  //
+  // MAP - Port Mapping Register
+  // PCI Offset:   90h - 93h
+  // Value [23:16] Port Disabled
+  //       [7:0]   Port Clock Disabled
+  //
+  MmioOr32 (PciSataRegBase + R_SATA_MAP, (UINT32) ((~SataPortsEnabled << N_SATA_MAP_SPD) & B_SATA_MAP_SPD));
+  DEBUG ((DEBUG_INFO, "MAP = 0x%x\n", MmioRead32 (PciSataRegBase + R_SATA_MAP)));
+  S3BootScriptSaveMemWrite (
+    S3BootScriptWidthUint32,
+    (UINTN) (PciSataRegBase + R_SATA_MAP),
+    1,
+    (VOID *) (UINTN) (PciSataRegBase + R_SATA_MAP)
+    );
+
+  MmioOr16 (PciSataRegBase + 0x94, SataPortsEnabled);
+  S3BootScriptSaveMemWrite (
+    S3BootScriptWidthUint16,
+    (UINTN) (PciSataRegBase + 0x94),
+    1,
+    (VOID *) (UINTN) (PciSataRegBase + 0x94)
+    );
+
+  //
+  // Step 14
+  // Program SATA PCI offset 9Ch [31] to 1b
+  //
+  MmioOr32 ((UINTN) (PciSataRegBase + R_SATA_SATAGC), BIT31);
+  S3BootScriptSaveMemWrite (
+    S3BootScriptWidthUint32,
+    (UINTN) (PciSataRegBase + R_SATA_SATAGC),
+    1,
+    (VOID *) (UINTN) (PciSataRegBase + R_SATA_SATAGC)
+    );
+  DEBUG ((DEBUG_INFO, "SATAGC = 0x%x\n", MmioRead32 (PciSataRegBase + R_SATA_SATAGC)));
+  DEBUG ((DEBUG_INFO, "ConfigureSataDxe() End\n"));
+
+  return EFI_SUCCESS;
+}
 
-- 
2.7.0.windows.1