Help Required legacy booting from an EFI

Help Required legacy booting from an EFI

[Saqib Khan]

Hello all, this is my first post to this list and i am very new to edk2
development.

I started by building BootManagerMenuApp with following functionality

   - Boot from BootManagerManueApp
   - Run an Helloworld EFI
   - Run windows 7 EFI to boot windows 7

Now i want to develop an EFI which will first run Helloworld EFI then it
will boot windows 7 which is installed on legacy boot (NOT EFI).

I have looked through http://bluestop.org/edk2/docs/trunk/ documentation
thoroughly but i am not able to get any thing for legacy boot from an EFI.


It will be helpful if someone guide me the flow for legacy booting from an
EFI .

-- 
Regards
saqib khan

Re: Help Required legacy booting from an EFI

[Laszlo Ersek]

On 09/19/16 17:00, Saqib Khan wrote:
> Hello all, this is my first post to this list and i am very new to edk2
> development.
> 
> I started by building BootManagerMenuApp with following functionality
> 
>    - Boot from BootManagerManueApp
>    - Run an Helloworld EFI
>    - Run windows 7 EFI to boot windows 7
> 
> Now i want to develop an EFI which will first run Helloworld EFI then it
> will boot windows 7 which is installed on legacy boot (NOT EFI).
> 
> I have looked through http://bluestop.org/edk2/docs/trunk/ documentation
> thoroughly but i am not able to get any thing for legacy boot from an EFI.
> 
> 
> It will be helpful if someone guide me the flow for legacy booting from an
> EFI .

You can add your EFI application to a SysPrep#### load option, then the
legacy-booted Windows OS to a normal Boot#### load option.

See "3.1.7 Required System Preparation Applications" in the UEFI-2.6
spec, about the ordering between SysPrep#### and Boot####.

Furthermore, legacy boot can be triggered by using a BBS (BIOS Boot
Specification) device path in the Boot#### option. This devpath node
type is documented in UEFI-2.6 "Table 98. Device Node Table", and in the
Compatibility Support Module Specification, rev 0.98, "3.2.1 Legacy BIOS
Protocol", near BBS_BBS_DEVICE_PATH.

For legacy boot to work, your platform firmware must of course include a
Compatibility Support Module.

As an example platform, SeaBIOS can be built as a CSM, then embedded
into OVMF with the -D CSM_ENABLE build switch. (Grep
OvmfPkg/OvmfPkg*.{dsc,fdf} for CSM_ENABLE.)

Specifically for Windows 7 though, you don't need a full CSM in order to
boot it under UEFI. You can boot it in UEFI mode just fine, as long as
you have some VBE services installed in the C segment. Windows 7 will
run those functions in its internal real-mode emulator, for setting up
the display:

https://en.wikipedia.org/wiki/Virtual_DOS_machine

That is, the VBE functions will not be executed natively, they will be
interpreted / emulated.

We utilized this fact for booting UEFI Windows 7 without a CSM on QEMU,
on the virtual QXL video card; see OvmfPkg/QemuVideoDxe/VbeShim.*.

Thanks
Laszlo

Re: Help Required legacy booting from an EFI

[Saqib Khan]

On Mon, Sep 19, 2016 at 10:49 PM, Laszlo Ersek <lersek@redhat.com> wrote:

> On 09/19/16 17:00, Saqib Khan wrote:
> > Hello all, this is my first post to this list and i am very new to edk2
> > development.
> >
> > I started by building BootManagerMenuApp with following functionality
> >
> >    - Boot from BootManagerManueApp
> >    - Run an Helloworld EFI
> >    - Run windows 7 EFI to boot windows 7
> >
> > Now i want to develop an EFI which will first run Helloworld EFI then it
> > will boot windows 7 which is installed on legacy boot (NOT EFI).
> >
> > I have looked through http://bluestop.org/edk2/docs/trunk/ documentation
> > thoroughly but i am not able to get any thing for legacy boot from an
> EFI.
> >
> >
> > It will be helpful if someone guide me the flow for legacy booting from
> an
> > EFI .
>
> You can add your EFI application to a SysPrep#### load option, then the
> legacy-booted Windows OS to a normal Boot#### load option.
>

Sysprep is not my option . :-(

>

>
> See "3.1.7 Required System Preparation Applications" in the UEFI-2.6
> spec, about the ordering between SysPrep#### and Boot####.
>
> Furthermore, legacy boot can be triggered by using a BBS (BIOS Boot
> Specification) device path in the Boot#### option. This devpath node
> type is documented in UEFI-2.6 "Table 98. Device Node Table", and in the
> Compatibility Support Module Specification, rev 0.98, "3.2.1 Legacy BIOS
> Protocol", near BBS_BBS_DEVICE_PATH.
>


Booting using BBS is my option,i was already looking for this and I have
attempted to modify EFIBootManagerMenuApp to work with legacy boot used ().

I have system with CSM support so essentially i will be doing all my work
on physical system not on virtual machine.

The detail you provided about BBS device path and then adding it to boot
menu is abstract for me .if you can detail this procedure a bit it will be
helpful, if required I can share the code snippet with you

Apart from this I am facing another issue, i created a boot-able USB with
EFI 2.0 shell in it . I have gabby motherboard(gigabyte h97- hd3) , I am
not able to launch EFI shell with any configuration it directly boots
windows no matter what I do, I attempted all USB port, and all
configuration like "boot from UEFI only" disabling secure boot. when I plug
US
B in another system which support UEFI but not CSM it works fine after
adding shell entry from USB. what might I be missing here?can you guide in
this case?


>
> For legacy boot to work, your platform firmware must of course include a
> Compatibility Support Module.
>
> As an example platform, SeaBIOS can be built as a CSM, then embedded
> into OVMF with the -D CSM_ENABLE build switch. (Grep
> OvmfPkg/OvmfPkg*.{dsc,fdf} for CSM_ENABLE.)
>
> Specifically for Windows 7 though, you don't need a full CSM in order to
> boot it under UEFI. You can boot it in UEFI mode just fine, as long as
> you have some VBE services installed in the C segment. Windows 7 will
> run those functions in its internal real-mode emulator, for setting up
> the display:
>
> https://en.wikipedia.org/wiki/Virtual_DOS_machine
>
> That is, the VBE functions will not be executed natively, they will be
> interpreted / emulated.
>
> We utilized this fact for booting UEFI Windows 7 without a CSM on QEMU,
> on the virtual QXL video card; see OvmfPkg/QemuVideoDxe/VbeShim.*.
>
> Thanks
> Laszlo
>
>


-- 
Regards
Saqib

Re: Help Required legacy booting from an EFI

[Laszlo Ersek]

CC'ing Ray

On 09/20/16 20:38, Saqib Khan wrote:
> 
> 
> On Mon, Sep 19, 2016 at 10:49 PM, Laszlo Ersek <lersek@redhat.com
> <mailto:lersek@redhat.com>> wrote:
> 
>     On 09/19/16 17:00, Saqib Khan wrote:
>     > Hello all, this is my first post to this list and i am very new to edk2
>     > development.
>     >
>     > I started by building BootManagerMenuApp with following functionality
>     >
>     >    - Boot from BootManagerManueApp
>     >    - Run an Helloworld EFI
>     >    - Run windows 7 EFI to boot windows 7
>     >
>     > Now i want to develop an EFI which will first run Helloworld EFI then it
>     > will boot windows 7 which is installed on legacy boot (NOT EFI).
>     >
>     > I have looked through http://bluestop.org/edk2/docs/trunk/
>     <http://bluestop.org/edk2/docs/trunk/> documentation
>     > thoroughly but i am not able to get any thing for legacy boot from an EFI.
>     >
>     >
>     > It will be helpful if someone guide me the flow for legacy booting from an
>     > EFI .
> 
>     You can add your EFI application to a SysPrep#### load option, then the
>     legacy-booted Windows OS to a normal Boot#### load option.
> 
> 
> Sysprep is not my option . :-(
> 
>  
> 
> 
>     See "3.1.7 Required System Preparation Applications" in the UEFI-2.6
>     spec, about the ordering between SysPrep#### and Boot####.
> 
>     Furthermore, legacy boot can be triggered by using a BBS (BIOS Boot
>     Specification) device path in the Boot#### option. This devpath node
>     type is documented in UEFI-2.6 "Table 98. Device Node Table", and in the
>     Compatibility Support Module Specification, rev 0.98, "3.2.1 Legacy BIOS
>     Protocol", near BBS_BBS_DEVICE_PATH.
> 
> 
> 
> Booting using BBS is my option,i was already looking for this and I have
> attempted to modify EFIBootManagerMenuApp to work with legacy boot used ().
> 
> I have system with CSM support so essentially i will be doing all my
> work on physical system not on virtual machine.
> 
> The detail you provided about BBS device path and then adding it to boot
> menu is abstract for me .if you can detail this procedure a bit it will
> be helpful, if required I can share the code snippet with you

It's been some time since I last tried CSM / legacy boot, but I think
when your platform BDS (= PlatformBootManagerLib instance) calls the
UefiBootManagerLib function called EfiBootManagerRefreshAllBootOption(),
that should generate (among other boot options) BBS boot options for all
suitable legacy OSes.

It seems that for this, you should link

IntelFrameworkModulePkg/Library/LegacyBootManagerLib/LegacyBootManagerLib.inf

into all the drivers and modules in your firmware -- via NULL library
resolution -- that consume UefiBootManagerLib. In OVMF's case at least,
the set of affected drivers is:

MdeModulePkg/Application/UiApp/UiApp.inf
MdeModulePkg/Universal/BdsDxe/BdsDxe.inf
MdeModulePkg/Universal/DriverHealthManagerDxe/DriverHealthManagerDxe.inf
NetworkPkg/HttpBootDxe/HttpBootDxe.inf

The important ones from these modules are likely the first two, UiApp
and BdsDxe.

(Theoretically any consumer of UefiBootManagerLib could call
EfiBootManagerRefreshAllBootOption(), and at that point you might want
LegacyBootManagerLib to have registered its "RefreshLegacyBootOption"
callback at construction time.)

In addition,

IntelFrameworkModulePkg/Library/LegacyBootMaintUiLib/LegacyBootMaintUiLib.inf

should likely be linked, via NULL resolution, into

MdeModulePkg/Application/UiApp/UiApp.inf

minimally.

(Example: please see the CSM_ENABLE parts under
"MdeModulePkg/Universal/BdsDxe/BdsDxe.inf" and
"MdeModulePkg/Application/UiApp/UiApp.inf" in OvmfPkg/OvmfPkg*dsc.
You'll find the above NULL library resolutions there.)

> 
> Apart from this I am facing another issue, i created a boot-able USB
> with EFI 2.0 shell in it . I have gabby motherboard(gigabyte h97- hd3) ,
> I am not able to launch EFI shell with any configuration it directly
> boots windows no matter what I do, I attempted all USB port, and all
> configuration like "boot from UEFI only" disabling secure boot. when I
> plug US
> B in another system which support UEFI but not CSM it works fine after
> adding shell entry from USB. what might I be missing here?can you guide
> in this case?

No clue. My take would have been "disable secure boot because your shell
binary is not signed", but you already tried that. Platform BDS is
platform-dependent, as its name says. Get another development board?

Laszlo

Re: Help Required legacy booting from an EFI

[Rod Smith]

On 09/20/2016 02:38 PM, Saqib Khan wrote:
> 
> Booting using BBS is my option,i was already looking for this and I have
> attempted to modify EFIBootManagerMenuApp to work with legacy boot used ().
> 
> I have system with CSM support so essentially i will be doing all my work
> on physical system not on virtual machine.
> 
> The detail you provided about BBS device path and then adding it to boot
> menu is abstract for me .if you can detail this procedure a bit it will be
> helpful, if required I can share the code snippet with you

You may want to look at the relevant bits of code in my rEFInd boot manager:

https://sourceforge.net/projects/refind/

In particular, look at the functions in EfiLib/legacy.c and
refind/legacy.c. One big caveat is that rEFInd includes TWO code paths
for launching BIOS-mode boot loaders -- one it inherits from its
predecessor project, rEFIt, and works only on Macs; and the other was
contributed by John Bressler and works only on UEFI-based PCs. Since I
wrote neither, I can't offer a lot of insight into how either one works.
(The Mac side, in particular, is pretty mysterious to me.) There may be
a better way to do it than what rEFInd does, but at least rEFInd's code
does work. Thus, if you need a concrete example, the rEFInd code might
be helpful.

-- 
Rod Smith
rodsmith@rodsbooks.com
http://www.rodsbooks.com

Re: Help Required legacy booting from an EFI

[Saqib Khan]

okay so i started with "MdeModulePkg\Application\BootManagerMenuApp"
addded follwoing package in inf file

   1. IntelFrameworkModulePkg/IntelFrameworkModulePkg.dec
   2. IntelFrameworkPkg/IntelFrameworkPkg.dec

and follwing libraries

   1. LegacyBootManagerLib
   2. LegacyBootMaintUiLib

and then i added library reference in C:\efi\test\edk2\DuetPkg/DuetPkgX6.dsc

   1.
   LegacyBootManagerLib|IntelFrameworkModulePkg/Library/LegacyBootManagerLib/LegacyBootManagerLib.inf
   2.
   LegacyBootMaintUiLib|IntelFrameworkModulePkg/Library/LegacyBootMaintUiLib/LegacyBootMaintUiLib.inf

Then in included  <Library/LegacyBootMaintUi.h> in
\MdeModulePkg\Application\BootManagerMenuApp\BootManagerMenuApp.h  then i
attempted top call " GetLegacyOptions
"


then i built it with
*Build -a X64 -p DuetPkg/DuetPkgX64.dsc *


It is unable to find LegacyBootMaintUi.h also .i am unable find where i am
wrong ...i have followed build path from

https://github.com/tianocore/tianocore.github.io/wiki/Getting-Started-Writing-Simple-Application


can any one point out where i am wrong?

On Wed, Sep 21, 2016 at 12:13 AM, Laszlo Ersek <lersek@redhat.com> wrote:

> CC'ing Ray
>
> On 09/20/16 20:38, Saqib Khan wrote:
> >
> >
> > On Mon, Sep 19, 2016 at 10:49 PM, Laszlo Ersek <lersek@redhat.com
> > <mailto:lersek@redhat.com>> wrote:
> >
> >     On 09/19/16 17:00, Saqib Khan wrote:
> >     > Hello all, this is my first post to this list and i am very new to
> edk2
> >     > development.
> >     >
> >     > I started by building BootManagerMenuApp with following
> functionality
> >     >
> >     >    - Boot from BootManagerManueApp
> >     >    - Run an Helloworld EFI
> >     >    - Run windows 7 EFI to boot windows 7
> >     >
> >     > Now i want to develop an EFI which will first run Helloworld EFI
> then it
> >     > will boot windows 7 which is installed on legacy boot (NOT EFI).
> >     >
> >     > I have looked through http://bluestop.org/edk2/docs/trunk/
> >     <http://bluestop.org/edk2/docs/trunk/> documentation
> >     > thoroughly but i am not able to get any thing for legacy boot from
> an EFI.
> >     >
> >     >
> >     > It will be helpful if someone guide me the flow for legacy booting
> from an
> >     > EFI .
> >
> >     You can add your EFI application to a SysPrep#### load option, then
> the
> >     legacy-booted Windows OS to a normal Boot#### load option.
> >
> >
> > Sysprep is not my option . :-(
> >
> >
> >
> >
> >     See "3.1.7 Required System Preparation Applications" in the UEFI-2.6
> >     spec, about the ordering between SysPrep#### and Boot####.
> >
> >     Furthermore, legacy boot can be triggered by using a BBS (BIOS Boot
> >     Specification) device path in the Boot#### option. This devpath node
> >     type is documented in UEFI-2.6 "Table 98. Device Node Table", and in
> the
> >     Compatibility Support Module Specification, rev 0.98, "3.2.1 Legacy
> BIOS
> >     Protocol", near BBS_BBS_DEVICE_PATH.
> >
> >
> >
> > Booting using BBS is my option,i was already looking for this and I have
> > attempted to modify EFIBootManagerMenuApp to work with legacy boot used
> ().
> >
> > I have system with CSM support so essentially i will be doing all my
> > work on physical system not on virtual machine.
> >
> > The detail you provided about BBS device path and then adding it to boot
> > menu is abstract for me .if you can detail this procedure a bit it will
> > be helpful, if required I can share the code snippet with you
>
> It's been some time since I last tried CSM / legacy boot, but I think
> when your platform BDS (= PlatformBootManagerLib instance) calls the
> UefiBootManagerLib function called EfiBootManagerRefreshAllBootOption(),
> that should generate (among other boot options) BBS boot options for all
> suitable legacy OSes.
>
> It seems that for this, you should link
>
> IntelFrameworkModulePkg/Library/LegacyBootManagerLib/
> LegacyBootManagerLib.inf
>
> into all the drivers and modules in your firmware -- via NULL library
> resolution -- that consume UefiBootManagerLib. In OVMF's case at least,
> the set of affected drivers is:
>
> MdeModulePkg/Application/UiApp/UiApp.inf
> MdeModulePkg/Universal/BdsDxe/BdsDxe.inf
> MdeModulePkg/Universal/DriverHealthManagerDxe/DriverHealthManagerDxe.inf
> NetworkPkg/HttpBootDxe/HttpBootDxe.inf
>
> The important ones from these modules are likely the first two, UiApp
> and BdsDxe.
>
> (Theoretically any consumer of UefiBootManagerLib could call
> EfiBootManagerRefreshAllBootOption(), and at that point you might want
> LegacyBootManagerLib to have registered its "RefreshLegacyBootOption"
> callback at construction time.)
>
> In addition,
>
> IntelFrameworkModulePkg/Library/LegacyBootMaintUiLib/
> LegacyBootMaintUiLib.inf
>
> should likely be linked, via NULL resolution, into
>
> MdeModulePkg/Application/UiApp/UiApp.inf
>
> minimally.
>
> (Example: please see the CSM_ENABLE parts under
> "MdeModulePkg/Universal/BdsDxe/BdsDxe.inf" and
> "MdeModulePkg/Application/UiApp/UiApp.inf" in OvmfPkg/OvmfPkg*dsc.
> You'll find the above NULL library resolutions there.)
>
> >
> > Apart from this I am facing another issue, i created a boot-able USB
> > with EFI 2.0 shell in it . I have gabby motherboard(gigabyte h97- hd3) ,
> > I am not able to launch EFI shell with any configuration it directly
> > boots windows no matter what I do, I attempted all USB port, and all
> > configuration like "boot from UEFI only" disabling secure boot. when I
> > plug US
> > B in another system which support UEFI but not CSM it works fine after
> > adding shell entry from USB. what might I be missing here?can you guide
> > in this case?
>
> No clue. My take would have been "disable secure boot because your shell
> binary is not signed", but you already tried that. Platform BDS is
> platform-dependent, as its name says. Get another development board?
>
> Laszlo
>



-- 
Regards
Saqib Ahmed Khanzada

Re: Help Required legacy booting from an EFI

[Laszlo Ersek]

On 09/22/16 13:25, Saqib Khan wrote:
> okay so i started with "MdeModulePkg\Application\BootManagerMenuApp" 
> addded follwoing package in inf file
> 
>  1. IntelFrameworkModulePkg/IntelFrameworkModulePkg.dec
>  2. IntelFrameworkPkg/IntelFrameworkPkg.dec
> 
> and follwing libraries
> 
>  1. LegacyBootManagerLib
>  2. LegacyBootMaintUiLib
> 
> and then i added library reference in C:\efi\test\edk2\DuetPkg/DuetPkgX6.dsc
> 
>  1. LegacyBootManagerLib|IntelFrameworkModulePkg/Library/LegacyBootManagerLib/LegacyBootManagerLib.inf
>  2. LegacyBootMaintUiLib|IntelFrameworkModulePkg/Library/LegacyBootMaintUiLib/LegacyBootMaintUiLib.inf
> 
> Then in included  <Library/LegacyBootMaintUi.h> in
> \MdeModulePkg\Application\BootManagerMenuApp\BootManagerMenuApp.h  then
> i attempted top call " GetLegacyOptions
> "
> 
> 
> then i built it with  *Build -a X64 -p DuetPkg/DuetPkgX64.dsc
> *
> 
> 
> It is unable to find LegacyBootMaintUi.h also .i am unable find where i
> am wrong ...i have followed build path from
> 
> https://github.com/tianocore/tianocore.github.io/wiki/Getting-Started-Writing-Simple-Application
> 
> 
> can any one point out where i am wrong?

The header file that you are trying to include, in the source code of
another module, is actually a library-internal header file:

IntelFrameworkModulePkg/Library/LegacyBootMaintUiLib/LegacyBootMaintUi.h

Library class header files that define public APIs always have pathnames
with the pattern

FooPkg/Include/Library/BarLib.h


I'm getting confused about what you want to achieve. You wrote "Now i
want to develop an EFI which will first run Helloworld EFI then it will
boot windows 7 which is installed on legacy boot (NOT EFI)."

To my knowledge, if you have a UEFI boot option for a legacy OS (with
the BBS devpath stuff in it), then EfiBootManagerBoot() in
UefiBootManagerLib can boot it transparently, assuming all the legacy
support has been built in (see my previous email).

Ultimately the legacy OS is booted with the
EFI_LEGACY_BIOS_PROTOCOL.LegacyBoot(), which takes the BBS device path
as a parameter. See LegacyBmBoot() in
"IntelFrameworkModulePkg/Library/LegacyBootManagerLib/LegacyBm.c".

Anyway I think this would be best discussed with Ray, as I'm just
another user of UefiBootManagerLib, through OVMF's PlatformBDS. What you
are trying to do doesn't seem like regular boot manager / Platform BDS
behavior.

Laszlo