From: "Antoine Coeur" <Coeur@gmx.fr>
To: edk2-devel@lists.01.org
Subject: [PATCH v2] ArmVirtPkg: Fix various typos
Date: Wed, 6 Feb 2019 16:48:50 +0100 [thread overview]
Message-ID: <trinity-70351b54-dcc4-4fc3-948b-343070d54ebf-1549468130483@3c-app-gmx-bs19> (raw)
Fix various typos in ArmVirtPkg.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Coeur <coeur@gmx.fr>
---
ArmVirtPkg/ArmVirt.dsc.inc | 2 +-
ArmVirtPkg/Library/ArmVirtDxeHobLib/HobLib.c | 2 +-
ArmVirtPkg/Library/BaseCachingPciExpressLib/PciExpressLib.c | 4 ++--
.../FdtPL011SerialPortLib/EarlyFdtPL011SerialPortLib.c | 6 +++---
.../Library/FdtPL011SerialPortLib/FdtPL011SerialPortLib.c | 6 +++---
ArmVirtPkg/Library/PlatformBootManagerLib/PlatformBm.c | 4 ++--
6 files changed, 12 insertions(+), 12 deletions(-)
diff --git a/ArmVirtPkg/ArmVirt.dsc.inc b/ArmVirtPkg/ArmVirt.dsc.inc
index c47955be94..304a4b4d21 100644
--- a/ArmVirtPkg/ArmVirt.dsc.inc
+++ b/ArmVirtPkg/ArmVirt.dsc.inc
@@ -333,7 +333,7 @@
# Values are in EFI Pages (4K). DXE Core will make sure that
# at least this much of each type of memory can be allocated
# from a single memory range. This way you only end up with
- # maximum of two fragements for each type in the memory map
+ # maximum of two fragments for each type in the memory map
# (the memory used, and the free memory that was prereserved
# but not used).
#
diff --git a/ArmVirtPkg/Library/ArmVirtDxeHobLib/HobLib.c b/ArmVirtPkg/Library/ArmVirtDxeHobLib/HobLib.c
index 73a0fbd8a4..758bc91ab1 100644
--- a/ArmVirtPkg/Library/ArmVirtDxeHobLib/HobLib.c
+++ b/ArmVirtPkg/Library/ArmVirtDxeHobLib/HobLib.c
@@ -1,5 +1,5 @@
/** @file
- HOB Library implemenation for Dxe Phase with DebugLib dependency removed
+ HOB Library implementation for Dxe Phase with DebugLib dependency removed
Copyright (c) 2006 - 2017, Intel Corporation. All rights reserved.<BR>
Copyright (c) 2014, Linaro Ltd. All rights reserved.<BR>
diff --git a/ArmVirtPkg/Library/BaseCachingPciExpressLib/PciExpressLib.c b/ArmVirtPkg/Library/BaseCachingPciExpressLib/PciExpressLib.c
index 6479f53b37..a083826bab 100644
--- a/ArmVirtPkg/Library/BaseCachingPciExpressLib/PciExpressLib.c
+++ b/ArmVirtPkg/Library/BaseCachingPciExpressLib/PciExpressLib.c
@@ -1238,7 +1238,7 @@ PciExpressBitFieldAndThenOr32 (
Size into the buffer specified by Buffer. This function only allows the PCI
configuration registers from a single PCI function to be read. Size is
returned. When possible 32-bit PCI configuration read cycles are used to read
- from StartAdress to StartAddress + Size. Due to alignment restrictions, 8-bit
+ from StartAddress to StartAddress + Size. Due to alignment restrictions, 8-bit
and 16-bit PCI configuration read cycles may be used at the beginning and the
end of the range.
@@ -1338,7 +1338,7 @@ PciExpressReadBuffer (
Size from the buffer specified by Buffer. This function only allows the PCI
configuration registers from a single PCI function to be written. Size is
returned. When possible 32-bit PCI configuration write cycles are used to
- write from StartAdress to StartAddress + Size. Due to alignment restrictions,
+ write from StartAddress to StartAddress + Size. Due to alignment restrictions,
8-bit and 16-bit PCI configuration write cycles may be used at the beginning
and the end of the range.
diff --git a/ArmVirtPkg/Library/FdtPL011SerialPortLib/EarlyFdtPL011SerialPortLib.c b/ArmVirtPkg/Library/FdtPL011SerialPortLib/EarlyFdtPL011SerialPortLib.c
index f0924dacbc..16c0e61816 100644
--- a/ArmVirtPkg/Library/FdtPL011SerialPortLib/EarlyFdtPL011SerialPortLib.c
+++ b/ArmVirtPkg/Library/FdtPL011SerialPortLib/EarlyFdtPL011SerialPortLib.c
@@ -234,13 +234,13 @@ SerialPortGetControl (
}
/**
- Sets the baud rate, receive FIFO depth, transmit/receice time out, parity,
+ Sets the baud rate, receive FIFO depth, transmit/receive time out, parity,
data bits, and stop bits on a serial device.
@param BaudRate The requested baud rate. A BaudRate value of 0 will use the
device's default interface speed.
On output, the value actually set.
- @param ReveiveFifoDepth The requested depth of the FIFO on the receive side of the
+ @param ReceiveFifoDepth The requested depth of the FIFO on the receive side of the
serial interface. A ReceiveFifoDepth value of 0 will use
the device's default FIFO depth.
On output, the value actually set.
@@ -253,7 +253,7 @@ SerialPortGetControl (
DefaultParity will use the device's default parity value.
On output, the value actually set.
@param DataBits The number of data bits to use on the serial device. A DataBits
- vaule of 0 will use the device's default data bit setting.
+ value of 0 will use the device's default data bit setting.
On output, the value actually set.
@param StopBits The number of stop bits to use on this serial device. A StopBits
value of DefaultStopBits will use the device's default number of
diff --git a/ArmVirtPkg/Library/FdtPL011SerialPortLib/FdtPL011SerialPortLib.c b/ArmVirtPkg/Library/FdtPL011SerialPortLib/FdtPL011SerialPortLib.c
index 8b736fd11f..2f10fb7b91 100644
--- a/ArmVirtPkg/Library/FdtPL011SerialPortLib/FdtPL011SerialPortLib.c
+++ b/ArmVirtPkg/Library/FdtPL011SerialPortLib/FdtPL011SerialPortLib.c
@@ -156,13 +156,13 @@ SerialPortPoll (
}
/**
- Sets the baud rate, receive FIFO depth, transmit/receice time out, parity,
+ Sets the baud rate, receive FIFO depth, transmit/receive time out, parity,
data bits, and stop bits on a serial device.
@param BaudRate The requested baud rate. A BaudRate value of 0 will use the
device's default interface speed.
On output, the value actually set.
- @param ReveiveFifoDepth The requested depth of the FIFO on the receive side of the
+ @param ReceiveFifoDepth The requested depth of the FIFO on the receive side of the
serial interface. A ReceiveFifoDepth value of 0 will use
the device's default FIFO depth.
On output, the value actually set.
@@ -175,7 +175,7 @@ SerialPortPoll (
DefaultParity will use the device's default parity value.
On output, the value actually set.
@param DataBits The number of data bits to use on the serial device. A DataBits
- vaule of 0 will use the device's default data bit setting.
+ value of 0 will use the device's default data bit setting.
On output, the value actually set.
@param StopBits The number of stop bits to use on this serial device. A StopBits
value of DefaultStopBits will use the device's default number of
diff --git a/ArmVirtPkg/Library/PlatformBootManagerLib/PlatformBm.c b/ArmVirtPkg/Library/PlatformBootManagerLib/PlatformBm.c
index bb07f5e22b..534357eff4 100644
--- a/ArmVirtPkg/Library/PlatformBootManagerLib/PlatformBm.c
+++ b/ArmVirtPkg/Library/PlatformBootManagerLib/PlatformBm.c
@@ -779,11 +779,11 @@ PlatformBootManagerBeforeConsole (
Do the platform specific action after the console is ready
Possible things that can be done in PlatformBootManagerAfterConsole:
> Console post action:
- > Dynamically switch output mode from 100x31 to 80x25 for certain senarino
+ > Dynamically switch output mode from 100x31 to 80x25 for certain scenario
> Signal console ready platform customized event
> Run diagnostics like memory testing
> Connect certain devices
- > Dispatch aditional option roms
+ > Dispatch additional option roms
> Special boot: e.g.: USB boot, enter UI
**/
VOID
--
2.17.2 (Apple Git-113)
next reply other threads:[~2019-02-06 15:48 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-02-06 15:48 Antoine Coeur [this message]
2019-02-06 16:33 ` [PATCH v2] ArmVirtPkg: Fix various typos Laszlo Ersek
2019-02-06 22:33 ` Philippe Mathieu-Daudé
2019-02-07 13:33 ` Laszlo Ersek
2019-02-07 17:13 ` Antoine Coeur
2019-02-07 17:48 ` Philippe Mathieu-Daudé
2019-02-08 8:16 ` Laszlo Ersek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-list from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=trinity-70351b54-dcc4-4fc3-948b-343070d54ebf-1549468130483@3c-app-gmx-bs19 \
--to=devel@edk2.groups.io \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox